XTOOL XTS500 Wireless Diagnostics Module User Manual

XTOOL XTS500 Wireless Diagnostics Module

ຂໍ້ມູນຈໍາເພາະ

• Operating temperature： 0~40℃
• Dimensions (W x H x D)：50 × 86.28× 25.50（mm）

ຄໍາແນະນໍາການນໍາໃຊ້ຜະລິດຕະພັນ

ການເຊື່ອມຕໍ່ໄຮ້ສາຍ

1. Connect OBDII-16 port of VCI Box to the vehicle’s DLC port.
2. Plug the USB wireless receiver into the USB port of the PC.
3. Go to the Wi-Fi selection page of your PC. Select WLAN 2 and search for the Wi-Fi hotspot with the same name as the SN of the device.
4. Once connected, your PC has established a connection with the device.

ການເຊື່ອມຕໍ່ສາຍໄຟ

1. Connect OBDII-16 port of VCI Box to the vehicle’s DLC port.
2. Connect the VCI and the diagnostic PC with a USB Type-C cable.

ຂໍ້ຄວນລະວັງໃນການວິນິດໄສ

• Ensure proper connections are made and follow safety protocols while performing diagnostics on vehicles.

About J2534 Toolbox
To install J2534 Toolbox:

1. ສະແກນລະຫັດ QR ຫຼືເຂົ້າໄປເບິ່ງ
   https://www.xtooltech.com/english/DownloadCenter.html to find the installation pack.
2. Unzip ດາວໂຫຼດ file and run Setup.exe. Follow the installation process.
3. After installation, restart your PC for changes to take effect.

ວິທີການນໍາໃຊ້
To use J2534 Toolbox:

• For wired connection: Directly connect the VCI to the diagnostic PC via USB cable. The Toolbox will detect the device automatically.
• If not detected, click the Refresh button to try again.
• For wireless connection: Plug in the WiFi Receiver, click the WiFi button, select WLAN 2, find the matching hotspot, and connect.
• Ensure a stable connection before proceeding with diagnostics.

ເຄື່ອງໝາຍການຄ້າ
XTOOL is a trademark of Shenzhen Xtooltech Intelligent Co., Ltd. Copyright, registered in China, the United States, and other countries. All other marks are trademarks or registered trademarks of their respective holders.

ການປະຕິເສດການຮັບປະກັນແລະການຈໍາກັດຄວາມຮັບຜິດຊອບ
All information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Xtool reserves the right to make changes at any time without notice. While information of this manual has been carefully checked for accuracy, no guarantee is given for the completeness and correctness of the contents, including but not limited to the product specifications, functions, and illustrations. Xtool will not be liable for any direct, special, incidental, or indirect damages, or for any economic consequential damages (including the loss of profits) as a result of using this product.

• Before operating or maintaining this unit, please read this manual carefully, please pay extra attention to the safety warnings and precautions.

ສະຫນັບສະຫນູນ & ບໍລິການ

• ທາງການ Webເວັບໄຊ: www.xtooltech.com
• ອີເມລ: xtoolinplusus@outlook.com

ແນະນໍາທົ່ວໄປ

Outlook & Ports

1. OBDII-16 port: Connect to vehicle’s DLC port.
2. Nameplate: Show device information.
3. Type-C Port: Connect the device to diagnosis PC via wire.
4. Indicator Light: Show device status.

ການເລີ່ມຕົ້ນ

 ການເຊື່ອມຕໍ່ຍານພາຫະນະ

ການເຊື່ອມຕໍ່ໄຮ້ສາຍ

1. Connect OBDII-16 port of VCI Box to vehicle’s DLC port.
2. Plug the USB wireless receiver into the USB port of the PC.
3. Go to Wi-Fi selection page of your PC. Select “WLAN 2”, and search for the Wi-Fi hotspot that has the same name as the SN of the device.
4. Once the hotspot is connected, your PC has established connection with the device.

ການເຊື່ອມຕໍ່ສາຍໄຟ

1. Connect OBDII-16 port of VCI Box to vehicle’s DLC port.
2. Connect the VCI and the diagnostic PC with a USB Type-C cable.

ຂໍ້ຄວນລະວັງໃນການວິນິດໄສ

1. ປະລິມານtage ຊ່ວງໃນລົດ: +9 ~ + 36V DC;
2. When testing some special functions, the operator must operate according to the prompts and meet the test conditions. In some cases, the conditions that need to be met are: engine water temperature 80 ℃~105 ℃, turn off headlights and air conditioners, keep the accelerator pedal in the released position, etc.;
3. ລະບົບການຄວບຄຸມເອເລັກໂຕຣນິກຂອງຮູບແບບທີ່ແຕກຕ່າງກັນແມ່ນສັບສົນຫຼາຍ. ຖ້າທ່ານພົບສະຖານະການທີ່ບໍ່ສາມາດທົດສອບໄດ້ຫຼືຂໍ້ມູນການທົດສອບຈໍານວນຫຼວງຫຼາຍແມ່ນຜິດປົກກະຕິ, ທ່ານສາມາດຄົ້ນຫາ ECU ຂອງຍານພາຫະນະແລະເລືອກເມນູສໍາລັບຕົວແບບໃນ nameplate ECU;
4. ສະເພາະສາຍສາຍໄຟທີ່ສະໜອງໃຫ້ໂດຍ XTOOL ແລະ ອອກແບບມາສໍາລັບອຸປະກອນທີ່ອະນຸຍາດໃຫ້ໃຊ້ກັບອຸປະກອນນີ້ເພື່ອຫຼີກເວັ້ນຄວາມເສຍຫາຍຕໍ່ຍານພາຫະນະ ຫຼື ອຸປະກອນ;
5. When running a diagnostics session, DO NOT shut down the device directly. You should cancel the task before returning to the main interface and then shutting down the device.

About J2534 Toolbox
J2534 Toolbox is a PC application that manage the updates and operation logs for all VCIs that supports J2534 function. Before you start working on diagnostics with your PC, make sure you have the J2534 Toolbox installed.

ການຕິດຕັ້ງ

• Scan the QR code on the right, or go to:https://www.xtooltech.com/english/DownloadCenter.html
• And find “J2534 Toolbox” for the installation pack.
• After the download is completed, unzip it and click “Setup.exe”, then follow the installation process. We suggest you to restart your PC after installation.

ວິທີການນໍາໃຊ້

• The picture on the right shows the main screen of the J2534 Toolbox when the VCI is not connected to the diagnostic PC.

Device Connection – Wired

• Directly connect the VCI to the diagnostic PC via USB cable. The Toolbox will automatically detect the device when you connect it.
• If the status has not been refreshed after you connect the VCI via wire, click the Refresh button to try again.

Device Connection – Wireless

1. Plug in the WiFi Receiver that comes with the VCI box.
2. Click the WiFi button on the bottom-left corner and select “WLAN 2” (or other numbers)
3. Find the hotspot that names the same as the SN of the VCI box and click “Connect”.
4. When the connection is ready, you are OK to go.

ໜ້າຈໍຫຼັກ
When the VCI is connected, you will see this screen:

• SN: Shows the SN of the current VCI.
• Firmware Version: Shows current firmware version that is installed on the VCI.
• Driver Version: Shows current driver version that is installed on the VCI.
• J2534 Authorization: Shows the VCI authorization status of current VCI.

• Log Record: Turn on/off the J2534 communication logs recording.
• Feedback: Send feedback to XTool customer service team when you meet any issues regarding the J2534 connection.

Firmware/Driver Update

• If there is an update for the firmware or the driver, you will see a red dot beside the version number. Click the Update button on the right to check updates.
• You can choose the version first, and click “Upgrade” button on the right to start updates.
• DO NOT DISCONNECT THE VCI WHEN THE UPDATE IS IN PROGRESS!

ການຕັ້ງຄ່າ

• Click the “Settings” button on the top-right corner and go to the Toolbox settings.
• Languages: Click to change language shown on the Toolbox.
• Version Number: Check the updates of the Toolbox.
• Log Cache: Show the size of the log folder. You can click the button on the right to clear all logs.
• Save Location: This shows the location of the log folder. You can click this to get into the folder.

• DoIP Mode Switch: When there are cases that the vehicle asks for a DoIP connection, please turn on the switch to enable DoIP mode. Please note that the DoIP mode can only be enabled in wired connection.

ຄໍາຕິຊົມ

If you meet any issues regarding J2534 connection, please record the logs (turn on the log recording switch) and send the logs to XTool customer service team. To better locate your problems, we need the following information in the report:

• ທີ່ຢູ່ອີເມວຂອງເຈົ້າ
• ບັນທຶກ files, recorded when the issues happened
• Vehicle information (brand, model, MY)
• Firmware/Driver version info
• A brief description on what is going on (you can also attach images & screenshots)

Our customer service team will handle this and reply to you via email.

ການປະຕິບັດຕາມ FCC

• FCC ID: 2AW3IV01W2

ອຸປະກອນນີ້ປະຕິບັດຕາມພາກທີ 15 ຂອງກົດລະບຽບ FCC. ການດໍາເນີນງານແມ່ນຂຶ້ນກັບສອງເງື່ອນໄຂດັ່ງຕໍ່ໄປນີ້:

1. ອຸປະກອນນີ້ອາດຈະບໍ່ເຮັດໃຫ້ເກີດການລົບກວນທີ່ເປັນອັນຕະລາຍ
2. ອຸ​ປະ​ກອນ​ນີ້​ຕ້ອງ​ຍອມ​ຮັບ​ການ​ແຊກ​ແຊງ​ໃດໆ​ທີ່​ໄດ້​ຮັບ​, ລວມ​ທັງ​ການ​ແຊກ​ແຊງ​ທີ່​ອາດ​ຈະ​ເຮັດ​ໃຫ້​ເກີດ​ການ​ດໍາ​ເນີນ​ງານ​ທີ່​ບໍ່​ຕ້ອງ​ການ​.

ຄຳເຕືອນ
ການ​ປ່ຽນ​ແປງ​ຫຼື​ການ​ດັດ​ແກ້​ທີ່​ບໍ່​ໄດ້​ຮັບ​ອະ​ນຸ​ມັດ​ຢ່າງ​ຊັດ​ເຈນ​ໂດຍ​ພາກ​ສ່ວນ​ທີ່​ຮັບ​ຜິດ​ຊອບ​ສໍາ​ລັບ​ການ​ປະ​ຕິ​ບັດ​ສາ​ມາດ​ເຮັດ​ໃຫ້​ສິດ​ທິ​ຂອງ​ຜູ້​ໃຊ້​ໃນ​ການ​ດໍາ​ເນີນ​ງານ​ອຸ​ປະ​ກອນ​ເປັນ​ໂມ​ຄະ​.

ໝາຍເຫດ
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient ຫຼືຍ້າຍເສົາອາກາດຮັບ.
• ເພີ່ມການແຍກຕ່າງຫາກລະຫວ່າງອຸປະກອນແລະເຄື່ອງຮັບ.
• ເຊື່ອມຕໍ່ອຸປະກອນກັບເຕົ້າສຽບຢູ່ໃນວົງຈອນທີ່ແຕກຕ່າງຈາກທີ່ເຄື່ອງຮັບແມ່ນເຊື່ອມຕໍ່.
• ປຶກສາຕົວແທນຈໍາໜ່າຍ ຫຼື ຊ່າງວິທະຍຸ/ໂທລະພາບທີ່ມີປະສົບການເພື່ອຂໍຄວາມຊ່ວຍເຫຼືອ.

ພາກສ່ວນທີ່ຮັບຜິດຊອບ

• ຊື່ບໍລິສັດ: FCC US Agent, LLC
• ທີ່ຢູ່: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA
• ອີເມວ: Support@FCCUSAgent.com

ຖະແຫຼງການ ISED

• IC: 29441-V01W2
• Model: XTS500
• PMN: V120，XTS500
• HVIN: V01W2A

ອຸ​ປະ​ກອນ​ນີ້​ປະ​ກອບ​ດ້ວຍ​ເຄື່ອງ​ສົ່ງ​ຂໍ້​ຍົກ​ເວັ້ນ​ໃບ​ອະ​ນຸ​ຍາດ / ຜູ້​ຮັບ​ທີ່​ປະ​ຕິ​ບັດ​ຕາມ​ນະ​ວັດ​ຕະ​ກໍາ​, ວິ​ທະ​ຍາ​ສາດ​ແລະ​ການ​ພັດ​ທະ​ນາ​ເສດ​ຖະ​ກິດ​ກາ​ນາ​ດາ​ການ​ຍົກ​ເວັ້ນ​ໃບ​ອະ​ນຸ​ຍາດ RSS​. ການດໍາເນີນງານແມ່ນຂຶ້ນກັບສອງເງື່ອນໄຂດັ່ງຕໍ່ໄປນີ້:

1. ອຸປະກອນນີ້ອາດຈະບໍ່ເຮັດໃຫ້ເກີດການລົບກວນ.
2. ອຸ​ປະ​ກອນ​ນີ້​ຕ້ອງ​ຍອມ​ຮັບ​ການ​ແຊກ​ແຊງ​ໃດ​ຫນຶ່ງ​, ລວມ​ທັງ​ການ​ແຊກ​ແຊງ​ທີ່​ອາດ​ຈະ​ເຮັດ​ໃຫ້​ການ​ເຮັດ​ວຽກ​ທີ່​ບໍ່​ຕ້ອງ​ການ​ຂອງ​ອຸ​ປະ​ກອນ​.

CE

• ປະກາດຄວາມສອດຄ່ອງ
• ດັ່ງນັ້ນ, ບໍລິສັດ Shenzhen XTOOLtech Intelligent Co., Ltd ປະກາດວ່າໂມດູນການວິນິດໄສແບບໄຮ້ສາຍນີ້ແມ່ນສອດຄ່ອງກັບຄວາມຕ້ອງການທີ່ຈໍາເປັນແລະຂໍ້ກໍານົດທີ່ກ່ຽວຂ້ອງອື່ນໆຂອງຄໍາສັ່ງ 2014/53/EU. ອີງຕາມມາດຕາ 10(2) ແລະມາດຕາ 10(10), ຜະລິດຕະພັນນີ້ອະນຸຍາດໃຫ້ນໍາໃຊ້ໃນທຸກປະເທດສະມາຊິກ EU.

UKCA

• ທີ່ນີ້, Shenzhen XTOOLtech Intelligent Co., Ltd ປະກາດວ່າໂມດູນການວິນິດໄສໄຮ້ສາຍນີ້ຕອບສະຫນອງກົດລະບຽບດ້ານວິຊາການທັງຫມົດທີ່ນໍາໃຊ້ກັບຜະລິດຕະພັນພາຍໃນຂອບເຂດຂອງກົດລະບຽບອຸປະກອນວິທະຍຸອັງກິດ (SI 2017/1206); ກົດລະບຽບອຸປະກອນໄຟຟ້າຂອງອັງກິດ (ຄວາມປອດໄພ) (SI 2016/1101); ແລະກົດລະບຽບການເຂົ້າກັນໄດ້ຂອງແມ່ເຫຼັກໄຟຟ້າຂອງອັງກິດ (SI 2016/1091) ແລະປະກາດວ່າຄໍາຮ້ອງສະຫມັກດຽວກັນບໍ່ໄດ້ຢູ່ໃນຫ້ອງອື່ນໆທີ່ໄດ້ຮັບອະນຸມັດຈາກອັງກິດ.
• Shenzhen Xtooltech Intelligent Co., Ltd.
• ເພີ່ມ: 17&18/F, A2 Building, Creative City, Liuxian Avenue, Nanshan District, Shenzhen, ຈີນ
• Shenzhen HQ ໂທ: +86 755 2399608
• ອີເມລ: marketing@xtooltech.com

FAQs