ຕິດຕັ້ງຄູ່ມື
CSEN1
CSEN1 Combo Sensor Controller
Part Numbers: CSEN1-H-W-ZHA (white enclosure) and CSEN1-H-G-ZHA (gray enclosure)
ລາຍລະອຽດ
The CSEN1 is a low voltage Networked Lighting Controller with an integrated passive infrared sensor and a photocell. It is powered via the AUX power from the LED driver. The CSEN1 autodetects both 0-10V Drivers and D4i Drivers to simplify the installation. The product is DLC certified for both indoor and outdoor applications.
ຂໍ້ມູນຈໍາເພາະ
- ຄວາມຖີ່ວິທະຍຸ: 2.4 GHz (IEEE 802.15.4)
- ພະລັງງານສົ່ງສັນຍານ RF: +20dBM
- ອຸນຫະພູມການເຮັດວຽກ: -40 ° C ເຖິງ +70 ° C
- ຄວາມຊຸ່ມຊື່ນໃນການເຮັດວຽກ: 10 ຫາ 95%, ບໍ່ condensing
- ການຫຸ້ມຫໍ່ທີ່ມີການຈັດອັນດັບ IP66
- ຂະໜາດ: 3.1" D x 1.6" H (80mm D x 42mm H)
- Input Power: 12-24VDC, 35mA max, 840mW
- ຈຸດປະສົງຂອງການຄວບຄຸມ: ການດໍາເນີນງານ
- Environmental: Indoor/Outdoor
- ລະດັບມົນລະພິດ: 3
- ຈັດອັນດັບ Volulse Voltage: 330V
ການພິຈາລະນາການອອກແບບ
Below are some recommendations for successful analog dimming using the CSEN1. The analog dimming control wires are referenced as DALI+/DIM+ and Common Ground/DALI-. The dimming signals have a Maximum voltage ຂອງ 10V ຊິງຕັນດີຊີ.
- Do not ground the Common Ground/DALI- wire to chassis ground; this is a return signal and is critical for proper dimming.
- ວາງສາຍໄຟອ່ອນໆໃຫ້ຫ່າງຈາກສາຍ AC ຖ້າເປັນໄປໄດ້.
- ສູງສຸດຂອງ 4 DALI-2/D4i LED Drivers ຕໍ່ຕົວຄວບຄຸມ, ປຶກສາ Synapse Support ຖ້າຕ້ອງການອັດຕາສ່ວນຫຼາຍກວ່າເກົ່າ.
- Maximum of 8 DIM to OFF LED Drivers for DIM to OFF Designs.
- ຢ່າຕິດໃສ່ເຄື່ອງເຮັດຄວາມຮ້ອນ ຫຼືໃສ່ໄດເວີ LED.
ໝາຍເຫດ: ໄດເວີ LED ຕ້ອງຮອງຮັບການທໍາງານຂອງ DIM ເພື່ອປິດ.
ຄຳເຕືອນ ແລະຂໍ້ຄວນລະວັງ
- TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
- The CSEN1 should only be installed in a fixture with a Zhaga Book 18 receptacle.
- ການບໍ່ປະຕິບັດຕາມຄໍາແນະນໍາ ແລະຄໍາເຕືອນເຫຼົ່ານີ້ອາດຈະເຮັດໃຫ້ການຮັບປະກັນເປັນໂມຄະ.
- This product must be installed in accordance with national, state, and local electrical codes and requirements.
- If you are unsure about any part of these instructions, consult an electrician; qualified personnel should perform all work.
ລາຍລະອຽດສາຍໄຟຂອງປື້ມ ZHAGA 18 SOCKET
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
For fixtures with an existing Zhaga socket, prior to installation, verify the wiring per the details below. (See Figure 1) If the fixture does not have a Zhaga socket, use the appropriate Wired Adapter accessory based on the knockout size: CSEN1-ZHA-ADPT-22 for 22mm knockouts, or CSEN1-ZHA-ADPT-33 for 33mm knockouts. The specifications for the signal wires are:
- 12-24VDC POWER: Brown
- Common Ground/DALI-: Pink with White Stripe
- DALI+/DIM+: Violet with White Stripe
- Solid Conductor, 105°C, Rated for 600VAC, AWG 20, 15” Length
ຮູບ 1 
ຄໍາແນະນໍາການຕິດຕັ້ງ
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
- ຖ້າເປັນໄປໄດ້, ໃຫ້ຖອດຝາປິດປະທັບຕາ ຫຼືອຸປະກອນຄວບຄຸມແສງໄຟທີ່ຕິດຕັ້ງຢູ່ໃນກ່ອງຮັບອຸປະກອນ.
- Align the CSEN1 such that the contacts pins are positioned at the appropriate the receptacle contacts.
- After alignment, push until the CSEN1 is fully seated within the receptacle.
- While pushing against the device, twist the CSEN1 housing clockwise until it locks into place. The CSEN1 includes a latching key or notch that will lock into position with an audible “click”. (See Figure 2)
ໝາຍເຫດ: ເພື່ອເຮັດວຽກຢ່າງຖືກຕ້ອງ, ໃຫ້ແນ່ໃຈວ່າໃສ່ຕົວຄວບຄຸມເຂົ້າໄປໃນເຕົ້າຮັບຢ່າງສົມບູນແລະບິດເຂົ້າໄປໃນຕໍາແຫນ່ງທີ່ລັອກ.
ຄຳເຕືອນ: The Zhaga receptacle should not turn during installation. Turning the receptacle could damage the internal fixture wiring by pulling it loose.
ຮູບ 2
ໄຟ LED ສະຖານະ
| ພະລັງງານໄຟ LED | ສະຖານະ |
| ສີຟ້າ | On for 3 seconds at Startup, then Off |
| ສະຖານະພາບ LED | ສະຖານະ |
| ສີແດງ | No script on the device |
| ກະພິບສີແດງ | ການສື່ສານຜິດພາດ |
| ກະພິບສີຟ້າ | Communication, No Config |
| ກະພິບສີຂຽວ | Normal Operation with Motion |
| ປິດ | Normal Operation, no Motion |
ຂໍ້ມູນລະບຽບການແລະການຢັ້ງຢືນ
RF Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
ການຢັ້ງຢືນອຸດສາຫະກໍາການາດາ (IC): ເຄື່ອງດິຈິຕອນນີ້ບໍ່ເກີນຂອບເຂດຈໍາກັດຂອງ Class B ສໍາລັບການປ່ອຍສຽງວິທະຍຸຈາກອຸປະກອນດິຈິຕອນທີ່ກໍານົດໄວ້ໃນກົດລະບຽບການແຊກແຊງທາງວິທະຍຸຂອງກົມການສື່ສານການາດາ.
ການຢັ້ງຢືນ FCC ແລະຂໍ້ມູນກົດລະບຽບ (ສະຫະລັດເທົ່ານັ້ນ)
FCC Part 15 Class B: ອຸປະກອນນີ້ປະຕິບັດຕາມພາກທີ 15 ຂອງກົດລະບຽບ FCC. ການດໍາເນີນງານແມ່ນຂຶ້ນກັບສອງເງື່ອນໄຂຕໍ່ໄປນີ້: (1) ອຸປະກອນເຫຼົ່ານີ້ອາດຈະບໍ່ເຮັດໃຫ້ເກີດການລົບກວນທີ່ເປັນອັນຕະລາຍ, ແລະ (2) ອຸປະກອນເຫຼົ່ານີ້ຕ້ອງຍອມຮັບການແຊກແຊງໃດໆທີ່ໄດ້ຮັບ, ລວມທັງການລົບກວນທີ່ອາດຈະເຮັດໃຫ້ເກີດອັນຕະລາຍຕໍ່ການດໍາເນີນງານ.
RADIO FREQUENCY INTERFERENCE (RFI) (FCC 15.105): This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Re-orient or relocate the receiving antenna; (2) Increase the separation between the equipment and the receiver; (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; (4) Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity (FCC 96-208 & 95-19): Synapse Wireless, Inc. declares that the product name CSEN1 to which this declaration relates, meet the requirements specified by the Federal Communications Commission as detailed in the following specifications:
- ສ່ວນທີ 15, ສ່ວນຍ່ອຍ B, ສໍາລັບອຸປະກອນຊັ້ນ B
- FCC 96-208 ຍ້ອນວ່າມັນໃຊ້ກັບຄອມພິວເຕີສ່ວນບຸກຄົນ Class B ແລະອຸປະກອນຕໍ່ພ່ວງ
- ຜະລິດຕະພັນນີ້ໄດ້ຖືກທົດສອບຢູ່ໃນຫ້ອງທົດລອງພາຍນອກທີ່ໄດ້ຮັບການຢັ້ງຢືນຕາມກົດລະບຽບ FCC ແລະໄດ້ຖືກພົບເຫັນວ່າຕອບສະຫນອງ FCC, Part 15, ຂອບເຂດຈໍາກັດການປ່ອຍອາຍພິດ. ເອກະສານເປີດຢູ່ file ແລະສາມາດໃຊ້ໄດ້ຈາກ Synapse Wireless, Inc.
ຖ້າ FCC ID ສໍາລັບໂມດູນພາຍໃນກ່ອງຫຸ້ມຜະລິດຕະພັນນີ້ບໍ່ເຫັນເມື່ອຕິດຕັ້ງຢູ່ໃນອຸປະກອນອື່ນ, ຫຼັງຈາກນັ້ນ, ພາຍນອກຂອງອຸປະກອນທີ່ຜະລິດຕະພັນນີ້ຖືກຕິດຕັ້ງຕ້ອງສະແດງປ້າຍຊື່ທີ່ອ້າງອີງໃສ່ໂມດູນ FCC ID. ການແກ້ໄຂ (FCC 15.21):
ການປ່ຽນແປງຫຼືການປັບປຸງອຸປະກອນນີ້ບໍ່ໄດ້ຮັບການອະນຸມັດຢ່າງຈະແຈ້ງໂດຍ Synapse Wireless, Inc., ອາດຈະຂາດສິດອໍານາດຂອງຜູ້ໃຊ້ໃນການປະຕິບັດອຸປະກອນນີ້.
ສິດທິບັດ – ເຄື່ອງໝາຍສະເໝືອນຢູ່ https://www.synapsewireless.com/about/patents
ເພື່ອຮຽນຮູ້ເພີ່ມເຕີມ: synapsewireless.com
ໃບຢັ້ງຢືນ
| ຕົວແບບ | CSEN1-H-W-ZHA (white enclosure) or CSEN1-H-G-ZHA (gray enclosure) |
| ປະກອບດ້ວຍບັດປະ ຈຳ ຕົວຂອງ FCC | QOQ-GM240P |
| ປະກອບມີ IC | 5123A-GM240P |
| ROHS 3 | 2011/65/EU (2015/863) |
| ການເຂົ້າເຖິງ EU | (EC) ເລກທີ 1907/2006 |
DALI-2 Certified Application Controller
ເອກະສານ / ຊັບພະຍາກອນ
 |
Synapse CSEN1 Combo Sensor Controller [pdf] ຄູ່ມືການຕິດຕັ້ງ CSEN1-H-W-ZHA, CSEN1-H-G-ZHA, CSEN1 Combo Sensor Controller, CSEN1, Combo Sensor Controller, Sensor Controller, Controller |