CITADEL MESH
MIDI TOWER CASE
ຄູ່ມືຜູ້ໃຊ້
ເນື້ອໃນ
ເຊື່ອງ
ເນື້ອໃນຊຸດອຸປະກອນເສີມ
ການເອົາແຜງອອກ
ການຖອດແຜງໜ້າ/ຂ້າງ
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
ການຕິດຕັ້ງມໍເຕີ
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
ການຕິດຕັ້ງການສະຫນອງພະລັງງານ
ການຕິດຕັ້ງການສະຫນອງພະລັງງານ
- Place PSU in the bottom rear of the case, within the PSU shroud
- ຈັດວາງຮູແລະຮັບປະກັນດ້ວຍ screws
ການຕິດຕັ້ງບັດກາຟິກ/ບັດ PCI-E
ການຕິດຕັ້ງບັດກາຟິກ/ບັດ PCI-E
- ຖອດຝາປິດສະລັອດຕິງ PCI-E ດ້ານຫຼັງອອກຕາມຄວາມຈໍາເປັນ (ຂຶ້ນກັບຂະໜາດຂອງບັດຂອງເຈົ້າ)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
ການຕິດຕັ້ງ SSD 2.5″ (ທາງຫນ້າ)
- Align your drive over the screw holes and secure with screws from the rear
2.5″ ການຕິດຕັ້ງ SDD (R)
2.5″ ການຕິດຕັ້ງ SSD (ດ້ານຫລັງ)
Place your SSD on top of the HDD bracket and secure with screws
ການຕິດຕັ້ງ HDD 3.5″
ການຕິດຕັ້ງ HDD 3.5″
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
ການຕິດຕັ້ງພັດລົມສູງສຸດ
ການຕິດຕັ້ງພັດລົມສູງສຸດ
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
ການຕິດຕັ້ງພັດລົມດ້ານໜ້າ/ຫລັງ
ການຕິດຕັ້ງພັດລົມດ້ານໜ້າ/ຫລັງ
- Align your fan to the screw holes on the chassis and secure with screws
ການຕິດຕັ້ງລັງສີນ້ຳເຢັນ
ການຕິດຕັ້ງລັງສີນ້ຳເຢັນ
- ຍຶດພັດລົມໃສ່ລັງສີ, ຈາກນັ້ນຍຶດລັງສີພາຍໃນຕົວເຄື່ອງໂດຍການຍຶດດ້ວຍສະກູຈາກພາຍນອກ.
ການຕິດຕັ້ງ I/O Panel
ການຕິດຕັ້ງ I/O Panel
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
ເອກະສານ / ຊັບພະຍາກອນ
 |
KOLINK ANL-INT Citadel Mesh Midi Tower Case [pdf] ຄູ່ມືຜູ້ໃຊ້ ANL-INT, ANL-INT Citadel Mesh Midi Tower Case, Citadel Mesh Midi Tower Case, Mesh Midi Tower Case, Midi Tower Case, Tower Case |