ຕິດຕັ້ງ Cisco Catalyst Network Interface Module
ພາກນີ້ໃຫ້ຂໍ້ມູນກ່ອນ ແລະໃນລະຫວ່າງການຕິດຕັ້ງ Cisco Catalyst Network Interface Modules (NIMs) ເທິງເວທີ Cisco Catalyst 8200 Series Edge.
ເກີນview ຂອງໂມດູນການໂຕ້ຕອບເຄືອຂ່າຍ
The Cisco Catalyst Network Interface Module (NIM) is supported on Cisco Catalyst 8200 Series Edge Platforms.
These are the steps to install a NIM:
1. ຊອກຫາຊ່ອງໃສ່ NIM ຢູ່ແຖບດ້ານໜ້າ.
2. Loosen the screws to remove NIM blank cover.
3. ສຽບ NIM ເຂົ້າໄປໃນຊ່ອງສຽບ.
4. ຮັດສະກູເພື່ອຍຶດ NIM ໃນຊ່ອງສຽບ.
These are the steps to remove a NIM:
1. If the NIM is up and running, issue the following command to shut down the NIM gracefully before removing it:
hw-module subslot slot 0/2 stop
ຂໍ້ຄວນລະວັງ If you do not shut down the NIM gracefully before removing it, the NIM card could get damaged.
2. ຊອກຫາຊ່ອງໃສ່ NIM ຢູ່ແຖບດ້ານໜ້າ.
3. ຖອດສະກູທີ່ຮັບປະກັນ NIM.
4. ຄ່ອຍໆດຶງ NIM ອອກຈາກຊ່ອງສຽບ.
All module slots must have a module or blank installed for the product to work thermally and for safety purposes.
ສໍາລັບຂໍ້ມູນເພີ່ມເຕີມ, ເບິ່ງແຜ່ນຂໍ້ມູນຂອງ Cisco Catalyst 8200 Series Edge Platforms ຢູ່ໃນ cisco.com ສໍາລັບບັນຊີລາຍຊື່ຂອງ NIM ທີ່ຮອງຮັບໃນເວທີຕ່າງໆ.
ເອົາອອກ ແລະຕິດຕັ້ງໂມດູນການໂຕ້ຕອບເຄືອຂ່າຍ
Keep the following tools and equipment while working with the Network Interface Modules (NIM)s:
- ເບີ 1 ໄຂຄອດ Phillips ຫຼື screwdriver ໃບແປຂະຫນາດນ້ອຍ
- ສາຍແຂນປ້ອງກັນ ESD
ເອົາໂມດູນການໂຕ້ຕອບເຄືອຂ່າຍ
ຂັ້ນຕອນທີ 1 Shut down the electrical power to the slot in the device, turn off the electrical power to the device. Leave the power cable plugged-in to channel ESD voltages ກັບດິນ.
ຂັ້ນຕອນທີ 2 Remove all network cables from the rear panel of the device. Using a number 1 Phillips screwdriver, loosen the captive screws on the network interface module.
ຂັ້ນຕອນທີ 3 Slide the network interface module out.
ຂັ້ນຕອນທີ 4 If you are not replacing the module, install a blank faceplate over the empty slot to ensure proper air flow.
ຕິດຕັ້ງໂມດູນການໂຕ້ຕອບເຄືອຂ່າຍ Cisco Catalyst
ຂັ້ນຕອນທີ 1 Shut down the electrical power to the slot in the router by turning off the electrical power to the router. Leave the power cable plugged in to channel ESD voltages ກັບດິນ.
ຂັ້ນຕອນທີ 2 Remove all network cables from the rear panel of the device.
ຂັ້ນຕອນທີ 3 Remove the blank faceplates installed over the network interface module slot that you intend to use.
ໝາຍເຫດ Save blank faceplates for future use.
ຂັ້ນຕອນທີ 4 Align the module with the guides in the chassis walls or slot divider and slide it gently into the NIM slot on the device.
ຂັ້ນຕອນທີ 5 Push the module into place until you feel the edge connector seat securely into the connector on the router backplane. The module faceplate should contact the chassis rear panel.
ຂັ້ນຕອນທີ 6 Using a number 1 Phillips screwdriver, tighten the captive screws on the network interface module.
ຂັ້ນຕອນທີ 7 Connect the module to the network and re-enable the power to the slot in the device.
ຕິດຕັ້ງ Cisco Catalyst Network Interface Module
ເອກະສານ / ຊັບພະຍາກອນ
 |
CISCO 8200 Series Catalyst Network Interface Module [pdf] ຄູ່ມືຜູ້ໃຊ້ 8200 Series, 8200 Series Catalyst Network Interface Module, Catalyst Network Interface Module, Network Interface Module, Interface Module |