User Manual: Vacuum Tube Preamplifier Switching Power Supply Transformer

ແນະນຳ

This manual provides essential information for the safe and effective use of your GODIYMODULES Vacuum Tube Preamplifier Switching Power Supply Transformer. This power supply is designed to provide stable filament (6.3V 5A) and high voltage (300V 300mA) outputs from an AC input range of 100-265V. It is suitable for various vacuum tube applications, including medium-power single-ended amplifiers (e.g., FU-7, 6P3P, EL34) and low-power push-pull machines (e.g., 6P1, 6P14, 6V6, 6P6P, 6L6).

The unit features independent filament and high voltage outputs and includes built-in over-current, over-voltage, and short-circuit protection for reliable operation.

ເນື້ອໃນຊຸດ

• 1 x Vacuum Tube Preamplifier Switching Power Supply Transformer

ຂໍ້ມູນຈໍາເພາະ

ຂໍ້ມູນຄວາມປອດໄພ

• ຖອດສາຍໄຟອອກສະເໝີກ່ອນທີ່ຈະເຮັດການເຊື່ອມຕໍ່ ຫຼື ການປັບແຕ່ງໃດໆ.
• ອຸປະກອນນີ້ເຮັດວຽກດ້ວຍແຮງດັນສູງtages. Exercise extreme caution to avoid electric shock.
• Ensure proper ventilation to prevent overheating. Do not operate in a sealed enclosure without adequate airflow.
• Do not attempt to modify the power supply. Refer all servicing to qualified personnel.
• ຮັກສາໃຫ້ໄກຈາກເດັກນ້ອຍ.

ຄໍາແນະນໍາການຕິດຕັ້ງ

1. ການຕິດຕັ້ງ: Securely mount the power supply in your chassis. Consider the dimensions (10.3 cm length, 6.6 cm width, 3.5 cm height) and ensure it is installed close to a metal chassis for assisted heat dissipation, especially for power consumption exceeding 80W.
2. ການເຊື່ອມຕໍ່ພະລັງງານຂາເຂົ້າ: Connect your AC 100-265V power source to the designated input terminals. Ensure correct polarity if applicable, though AC input is typically non-polarized.
3. Filament Output Connection: Connect your vacuum tube's filament (heater) circuit to the 6.3V 5A output terminals. The filament output is independent.
4. ສູງtage Output Connection: Connect your vacuum tube's anode (plate) circuit to the 300V 300mA high voltage output terminals. This output is also independent.
5. Rectifier Filter Note: The power supply has its own built-in rectifier filter. If integrating into an existing circuit, remove any original filter capacitors and inductors to avoid redundancy or potential issues.
6. ການລະບາຍອາກາດ: Ensure the installation provides sufficient ventilation. Avoid placing the unit in a very small, sealed enclosure, as this can lead to overheating.

Image: GODIYMODULES Vacuum Tube Preamplifier Switching Power Supply Transformer with labeled dimensions (103mm length, 66mm width, 35mm height) and connection points for 220V input and ground wire. This illustrates the physical layout and connection terminals.

ຮູບພາບ: ເທິງລົງລຸ່ມ view of the power supply circuit board, showing the two yellow transformers, capacitors, and terminal blocks for connections.

ຄໍາແນະນໍາການດໍາເນີນງານ

1. ເປີດ: Once all connections are secure and verified, apply AC power to the unit.
2. Warm-up Delay: ສູງ voltage output will typically become active after a delay of approximately 30 seconds from power-on. This is a normal operational characteristic.
3. ຄວາມເຂົ້າກັນໄດ້ຂອງທໍ່: This power supply is compatible with a range of vacuum tubes, including FU-7, 6P3P, EL34 for medium-power single-ended configurations, and 6P1, 6P14, 6V6, 6P6P, 6L6 for low-power push-pull configurations. It can also support other small power single-ended tubes.
4. ປະສິດທິພາບສຽງ: When properly integrated, this power supply contributes to a robust bass, clear midrange, and detailed treble, with an ultra-low noise floor.

ບໍາລຸງຮັກສາ

• ທໍາຄວາມສະອາດ: ຮັກສາເຄື່ອງໃຫ້ປອດຈາກຂີ້ຝຸ່ນ ແລະສິ່ງເສດເຫຼືອ. ໃຊ້ຜ້າອ່ອນໆ, ແຫ້ງເພື່ອເຮັດຄວາມສະອາດ. ຢ່າໃຊ້ນໍ້າສະອາດ.
• ການລະບາຍອາກາດ: Regularly check that ventilation openings are not obstructed to ensure proper heat dissipation.
• ການເຊື່ອມຕໍ່: Periodically inspect all electrical connections to ensure they remain tight and secure.
• ເງື່ອນໄຂສິ່ງແວດລ້ອມ: Operate the power supply within its specified temperature and humidity ranges.

ການແກ້ໄຂບັນຫາ

• ບໍ່ມີ Output Voltage:
  • Verify the AC input power is connected and active (100-265V).
  • Check all output connections for proper wiring and shorts.
  • Allow approximately 30 seconds after power-on for the high voltage output to stabilize.
  • The unit has over-current, over-voltage, and short-circuit protection. If a fault occurs, the unit may shut down. Disconnect power, resolve the fault, and then reapply power.
• Lower Than Expected High Voltage ຜົນໄດ້ຮັບ:
  • Ensure the load current does not exceed the specified 300mA. Exceeding this limit can cause voltage sag or trigger protection.
  • ກວດສອບການປ້ອນຂໍ້ມູນ voltage ຢູ່ໃນລະດັບ 100-265V.
  • Allow the unit to warm up fully, as voltage may stabilize after some operating time.
• ຄວາມຮ້ອນເກີນ:
  • Ensure adequate ventilation. The power supply requires sufficient airflow, especially when operating above 80W.
  • Confirm the unit is mounted to a metal chassis to assist with heat dissipation.
  • Reduce the load if it consistently operates at its maximum specified current.

ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

For warranty information or technical support, please contact GODIYMODULES directly through their official channels or the retailer from whom the product was purchased. Please have your purchase details and product model information available when contacting support.