AUTOOL Automotive Multimeter Oscilloscope TRMS Instruction Manual

1. ຜະລິດຕະພັນເກີນview

The AUTOOL DM303 is a versatile automotive diagnostic multimeter and oscilloscope kit designed for comprehensive electrical testing in vehicles. It combines the functions of a digital multimeter with an oscilloscope, offering a wide range of measurement capabilities for both general electrical work and specialized automotive diagnostics.

Figure 1.1: AUTOOL DM303 Multimeter Oscilloscope and its accessories, including various test leads and a carrying case.

ຄຸນ​ນະ​ສົມ​ບັດ​ທີ່​ສໍາ​ຄັນ​:

• ຄວາມສາມາດ Multimeter: ວັດແທກຄວາມດັນ AC/DC ໄດ້ຢ່າງຖືກຕ້ອງtage (0-1000V DC, 0-700V AC), resistance (0-1MΩ), continuity, AC/DC current (0-20A, 0-200mA), capacitance, frequency (1-1MHz), diodes, and duty cycle.
• ໜ້າທີ່ຂອງອອດຊິວໂລສະໂຄບ: Features a 500KHz waveform test bandwidth for measuring slowly changing signals, ideal for automotive circuits such as motor drive signals, ignition signals, camshaft/crankshaft signals, wheel speed sensor signals, and oxygen sensor signals.
• Auto Range & True RMS: Automatically selects appropriate measurement ranges and provides accurate readings for non-sinusoidal waveforms.
• Specialized Wiring Functions: Includes 8 types of wiring lines for diverse applications, such as battery voltage testing, fuel injector/relay testing, K-wire and CAN bus signal testing, and ECU diagnostics.
• Starting Test & Analog Signal Output: Evaluates battery starter systems and outputs 5V square wave and 5Vpp sine wave signals (1Hz-10KHz, 10%-90% duty cycle).
• ຈໍສະແດງຜົນທີ່ເປັນມິດກັບຜູ້ໃຊ້: Equipped with a 2.8-inch colorful screen with backlight, adjustable brightness, button sound, and sleep time for enhanced readability and convenience in various working environments.

2. ການຕິດຕັ້ງແລະອົງປະກອບ

2.1 ເນື້ອໃນຊຸດ

The AUTOOL DM303 kit includes the main multimeter unit, various test leads, and a carrying case. Refer to the diagram below for a detailed view of the included wiring lines and their functions.

ຮູບ 2.1: ເກີນview of the 8 specialized wiring lines and their applications.

2.2 Device Layout and Connections

Familiarize yourself with the main components and connection points of the DM303 unit.

ຮູບ 2.2: ດ້ານຫນ້າແລະດ້ານຫລັງ view of the DM303 with key components labeled.

2.3 ການຕິດຕັ້ງເບື້ອງຕົ້ນ

To begin using the DM303, ensure the device is powered on and test probes are correctly connected.

1. ເປີດ: Press the power button to turn on the device. The screen will display the AUTOOL logo during startup.
2. Connect Test Probes: Insert the red test probe into the VΩA jack (red) and the black test probe into the COM jack (black). For current measurements, connect the red probe to the mA/µA jack (green) for small currents or the 10A jack (yellow) for larger currents, and the black probe to the COM jack.
3. ການ​ຕິດ​ຕັ້ງ​ຫມໍ້​ໄຟ​: The device uses AAA cells but has a socket for Li-Ion rechargeable batteries. Ensure batteries are correctly installed if not using the internal rechargeable option.

3. ຄໍາແນະນໍາການດໍາເນີນງານ

The AUTOOL DM303 offers various measurement modes accessible via the main menu. Use the directional keys and OK button to navigate and select functions.

3.1 Multimeter Functions

The DM303 functions as a comprehensive digital multimeter with auto-ranging capabilities.

ຮູບທີ 3.1: ຕົວຢ່າງamples ຂອງ voltage, current, and resistance measurements on the DM303 display.

ສະບັບທີ 3.1.1tage ການວັດແທກ (AC/DC)

ການ​ວັດ​ແທກ voltage, select the "Voltmeter" (V) function from the main menu. The device will automatically detect AC or DC voltage. For AC voltage, press the Fn key to switch to AC measurement mode.

3.1.2 ການວັດແທກກະແສໄຟຟ້າ (AC/DC)

Select the "Ammeter" (A) function. For small currents (mA/µA), connect the red probe to the green jack. For larger currents (up to 20A), connect the red probe to the yellow jack. Press F2 to switch between mA and 20A measurement modes.

3.1.3 ການວັດແທກຄວາມຕ້ານທານ

Select the "Ohmmeter" (Ω) function to measure resistance. The device supports continuity circuit tests and diode tests.

3.2 ໜ້າທີ່ຂອງອອດຊິວໂລສະໂຄບ

The oscilloscope function allows for waveform analysis of various automotive signals.

Figure 3.2: Oscilloscope display showing a waveform.

3.2.1 OBD Interface Testing

Use the oscilloscope function to test the OBD interface. Connect the test probes to the corresponding ports and observe the waveform while interacting with the vehicle (e.g., pressing the accelerator pedal) to identify abnormalities.

3.2.2 Camshaft Detection

The oscilloscope can be used to detect camshaft signals. Start the engine and insert the red test probe into the power circuit, touching the contact parts to be tested. Use the up/down keys to adjust voltage display per grid and left/right keys to switch frequency for detailed waveform analysis.

3.3 Automotive Specific Tests

3.3.1 ການທົດສອບ Cranking

Perform a cranking test to evaluate the battery's starter system. Connect the device to the battery terminals and initiate the engine start sequence. The DM303 will display current, minimum voltage, and starting voltage to assess battery health and starting power.

Figure 3.3: Cranking test in progress, showing the device connected to the car battery.

3.3.2 ການທົດສອບຫົວສີດ

The injector test function allows you to simulate engine speed to test fuel injectors. Connect the appropriate test lines to the injector and the DM303, then set the desired RPM to observe injector operation.

Figure 3.4: Injector test setup, simulating engine speed for diagnostic purposes.

ການທົດສອບການສົ່ງຕໍ່ 3.3.3

Test automotive relays by connecting them to the DM303 using the appropriate wiring. The device can check the contact status and resistance of the relay.

Figure 3.5: Relay test in progress, part of a composite image demonstrating multiple automotive diagnostic functions.

3.3.4 Ignition Pulse Signal Test

Measure ignition pulse signals to diagnose ignition system issues. Connect the ignition pulse signal test line and observe the waveform on the oscilloscope display.

3.3.5 K-line & CAN Bus Signal Test

The DM303 can test K-line and CAN bus signals, providing data for network communication diagnostics in vehicles.

3.3.6 Automotive Lamp Circuit Simulation Testing

Simulate and test automotive lamp circuits to check for functionality and identify damaged components. Use the red test probe to touch the car lights circuit and output voltage to drive the electrical component.

3.3.7 Analog Signal Output

The multimeter can output 5V square wave and 5Vpp sine wave signals with adjustable frequency (1Hz-10KHz) and duty cycle (10%-90%). This function is useful for testing various sensors and components that require a specific input signal.

Figure 3.6: Analog signal test in progress, part of a composite image demonstrating multiple automotive diagnostic functions.

4. ບໍາລຸງຮັກສາ

• ທໍາຄວາມສະອາດ: ເຊັດອຸປະກອນດ້ວຍຜ້າອ່ອນໆ, ແຫ້ງ. ຢ່າໃຊ້ເຄື່ອງເຮັດຄວາມສະອາດຂັດຫຼືສານລະລາຍ.
• ການເກັບຮັກສາ: Store the DM303 in its carrying case in a cool, dry place away from direct sunlight and extreme temperatures.
• ການດູແລຫມໍ້ໄຟ: If the device uses removable batteries, remove them if the unit will not be used for an extended period to prevent leakage. For the internal rechargeable battery, ensure it is charged periodically to maintain its health.
• Probe Care: Inspect test leads and probes regularly for any signs of wear, damage, or frayed insulation. Replace damaged components immediately to ensure accurate and safe operation.
• ອັບເດດຊອບແວ: ກວດເບິ່ງຜູ້ຜະລິດ webເວັບໄຊທ໌ສໍາລັບການອັບເດດເຟີມແວທີ່ມີຢູ່ເພື່ອຮັບປະກັນການປະຕິບັດທີ່ດີທີ່ສຸດແລະການເຂົ້າເຖິງຄຸນສົມບັດໃຫມ່.

5. ການແກ້ໄຂບັນຫາ

If you encounter issues with your AUTOOL DM303, refer to the following common troubleshooting steps:

• ອຸປະກອນບໍ່ເປີດ:
  • Ensure the battery is charged or correctly installed.
  • ກວດ​ສອບ​ວ່າ​ປຸ່ມ​ເປີດ​ປິດ​ໄດ້​ຖືກ​ກົດ​ດັນ​ຢ່າງ​ຫນັກ​ແຫນ້ນ​.
• ການອ່ານທີ່ບໍ່ຖືກຕ້ອງ:
  • Check that test probes are securely connected to the correct input jacks for the selected measurement type.
  • Ensure the probes are making good contact with the circuit or component being tested.
  • Verify the correct measurement mode is selected (e.g., AC vs. DC voltage, mA vs. 20A current).
  • Clean the probe tips if they appear dirty or corroded.
• ບໍ່ມີຈໍສະແດງຜົນ ຫຼືບໍ່ມີແສງ:
  • Adjust the screen brightness setting in the device menu.
  • ໃຫ້ແນ່ໃຈວ່າແບັດເຕີຣີມີຄ່າພຽງພໍ.
• Function Not Responding:
  • ປິດເປີດອຸປະກອນຄືນໃໝ່.
  • Ensure the correct accessory cable (e.g., C04 Multi-functional Test Cable) is properly connected for specialized tests.

If troubleshooting steps do not resolve the issue, please contact AUTOOL customer support for further assistance.

6. ຂໍ້ມູນຈໍາເພາະ

Figure 6.1: Visual representation of product dimensions and key specifications.

7. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

AUTOOL provides a ຮັບປະກັນສາມປີ for the DM303 against any quality problems. If the product has any defect, AUTOOL will provide a new replacement or solutions without delay. Lifetime technical support is also provided.

For any needs or technical assistance, you are welcome to contact AUTOOL customer support. They aim to respond within 24 hours.