ຄູ່ມືການໃຊ້ງານຄອມພິວເຕີລົດຖີບ Lixada VZI0506850041571VY

ແນະນຳ

This manual provides detailed instructions for the Lixada Bicycle Cycling Computer, Model VZI0506850041571VY. This digital device is designed to track various cycling metrics, featuring a rechargeable battery and backlight for enhanced visibility. Please read thoroughly before use to ensure proper installation and optimal operation.

ມີຫຍັງແດ່

ຊຸດປະກອບມີອົງປະກອບດັ່ງຕໍ່ໄປນີ້:

• ຄອມພິວເຕີລົດຖີບ
• ວົງເລັບ
• ເຊັນເຊີ
• ແມ່ເຫຼັກ
• Type-c USB Cable
• ຄູ່ມື

ຕັ້ງຄ່າ

1. ການຕິດຕັ້ງຫມໍ້ໄຟ

The Lixada Bicycle Cycling Computer and its wireless sensor require CR2032 batteries for operation. Ensure correct polarity (+ side facing upwards) when inserting the batteries.

2. ການຕັ້ງຄ່າວົງມົນລໍ້

Accurate wheel circumference setting is crucial for precise speed and distance readings. You can find your tire size in the table below or measure it manually.

To manually measure, mark a spot on your tire and roll the wheel one full revolution, then measure the distance. Input this value into the computer. For example, if your tire is 26" x 1.95", input 2055.

3. Unit Setting (KM/H or M/H)

After setting the wheel circumference, you can select your preferred unit of measurement (kilometers per hour or miles per hour) using the right button and confirming with the left button.

4. ການຕັ້ງໂມງ

Set the clock to either 12-hour or 24-hour format, then adjust the hour and minute using the right and left buttons respectively.

5. Handlebar Mount Installation

Attach the bracket to your bicycle's handlebar using the provided zip ties. Ensure it is securely fastened and positioned for optimal viewing.

6. Sensor and Magnet Installation

Install the wireless sensor on the front fork and the magnet on a spoke of the front wheel. The distance between the sensor and magnet should be less than 1.5mm for accurate readings. Use the provided zip ties to secure the sensor.

7. Signal Test

After installation, spin the front wheel to verify that the speed readings appear on the computer. If no readings are displayed, check the sensor and magnet alignment and distance. Ensure the distance between the computer and the sensor is less than 60cm.

ຄໍາແນະນໍາການດໍາເນີນງານ

The Lixada Bicycle Cycling Computer offers 16 functions to monitor your cycling performance. Use the buttons on the device to navigate through different modes and settings.

ໂໝດສະແດງຜົນ

• SPD (Speedometer): ສະແດງຄວາມໄວໃນປະຈຸບັນ.
• ODO (ເຄື່ອງວັດໄລຍະທາງ): Records total distance traveled (0.001-99999km/m).
• DST (Trip Distance): Shows distance covered in the current trip.
• MXS (Maximum Speed): Records the highest speed achieved.
• AVS (Average Speed): Calculates the average speed of the current trip.
• TM (Elapsed Time): Tracks the duration of the current trip.
• CLK (Clock): ສະແດງເວລາໃນຮູບແບບ 12 ຊົ່ວໂມງ ຫຼື 24 ຊົ່ວໂມງ.
• ແສງຫຼັງ: ເຮັດໃຫ້ມີແສງຈໍສະແດງຜົນສໍາລັບການເບິ່ງເຫັນໃນສະພາບແສງສະຫວ່າງຕ່ໍາ.
• ສະແກນ: Cycles through various display modes automatically.

ຣີເຊັດຂໍ້ມູນ

To reset trip-specific data (DST, TM, MXS, AVS), press and hold the left button for 3 seconds while in the respective mode. This will clear the current trip data.

ບໍາລຸງຮັກສາ

ການປ່ຽນແບັດ

The computer and sensor use CR2032 batteries. When the display becomes dim or erratic, it's time to replace the batteries. Ensure correct polarity during installation.

ການປະເມີນກັນນ້ໍາ

The device has an International Protection Rating of IP4, indicating it is protected against splashing water from any direction. It is not designed for submersion.

Sensor and Magnet Distance

Regularly check that the distance between the wireless sensor and the magnet on the spoke remains less than 1.5mm. If the distance increases, readings may become inaccurate or stop altogether. Adjust as needed.

ການແກ້ໄຂບັນຫາ

• ບໍ່​ມີ​ການ​ອ່ານ​ຄວາມ​ໄວ​: Check the distance between the sensor and magnet. Ensure it is less than 1.5mm. Verify batteries are correctly installed and charged.
• Screen Difficult to Read in Daylight: Some users report screen reflectivity issues in bright sunlight. Adjust the viewing angle or consider using the backlight in shaded conditions.
• ໄຟພື້ນຫຼັງບໍ່ເປີດຢູ່: The backlight may require frequent recharging or manual activation depending on the mode. Refer to the operating instructions for backlight settings.
• ການອ່ານທີ່ບໍ່ຖືກຕ້ອງ: Re-verify the wheel circumference setting. Ensure the sensor and magnet are securely mounted and their distance is optimal.
• ອົງປະກອບທີ່ຂາດຫາຍໄປ: If any essential part (e.g., magnet) is missing upon arrival, contact the seller for support.

ຂໍ້ມູນຈໍາເພາະ

ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

For warranty information or technical support, please refer to the product packaging or contact the manufacturer directly. Keep your purchase receipt for any warranty claims.