AVI-8 P-51 Mustang Blakeslee AV-4077 Chronograph Pilot Watch Instruction Manual

1. ບົດແນະນຳ

This manual provides essential instructions for the setup, operation, and maintenance of your AVI-8 P-51 Mustang Blakeslee AV-4077 Chronograph Pilot Watch. Please read this manual thoroughly to ensure proper use and longevity of your timepiece.

The AVI-8 P-51 Mustang Blakeslee watch features a 43mm stainless steel case with a black PVD finish and a scratch-resistant mineral crystal lens with anti-reflective coating. It is powered by a Japanese Meca-Quartz chronograph movement, offering precise timekeeping with luminous hands and markers for readability. The watch is water-resistant up to 50 meters and comes with a genuine black leather strap with a classic buckle closure.

ຮູບພາບ 1.1: ດ້ານຫນ້າ view of the AVI-8 P-51 Mustang Blakeslee AV-4077 Chronograph Pilot Watch.

2. ຄຸນສົມບັດ ແລະ ອົງປະກອບຂອງຜະລິດຕະພັນ

• ວັດສະດຸກໍລະນີ: ສະແຕນເລດ
• ຂອບ: Fixed Bezel
• ເລນ: Mineral Lens with Anti-Reflective Coating
• ແຖບ: 22mm Genuine Leather Strap
• ການເຄື່ອນໄຫວ: Japanese Meca-Quartz Chronograph
• ເຮືອນຍອດ: ດຶງອອກ
• ເສັ້ນຜ່າສູນກາງຂອງກໍລະນີ: 43ມມ
• ຄວາມຕ້ານທານນ້ໍາ: 50M

Image 2.1: Detailed diagram illustrating the key features and components of the Blakeslee Chronograph.

Image 2.2: The watch dial showcasing its luminous hands and markers for enhanced visibility in low-light conditions.

3. ຕັ້ງຄ່າ

3.1 ການຕັ້ງຄ່າເບື້ອງຕົ້ນ ແລະ ການຕັ້ງເວລາ

1. Before setting the time, ensure any plastic tab protecting the crown is removed.
2. Gently pull the crown (located on the right side of the watch case) out to its outermost position. This will stop the second hand.
3. ໝຸນມົງກຸດຕາມເຂັມໂມງ ຫຼື ທວນເຂັມໂມງເພື່ອຕັ້ງໂມງ ແລະ ນາທີເປັນເວລາທີ່ຕ້ອງການ.
4. ເມື່ອເວລາຖືກກໍານົດ, ຍູ້ເຮືອນຍອດກັບຄືນສູ່ຕໍາແຫນ່ງເດີມ. ມືທີສອງຈະສືບຕໍ່ການເຄື່ອນໄຫວ.

3.2 ການ ກຳ ນົດວັນທີ

1. Pull the crown out to the first click position (if applicable, otherwise use the outermost position).
2. Rotate the crown to adjust the date. Avoid setting the date between 9 PM and 3 AM, as this may interfere with the automatic date change mechanism.
3. Once the date is set, push the crown back into its original position.

4. ການໃຊ້ໂມງຈັບເວລາ

Your AVI-8 AV-4077 watch features a chronograph function for measuring elapsed time. The chronograph typically uses dedicated pushers on the side of the watch case.

4.1 ການເລີ່ມຕົ້ນ ແລະ ການຢຸດໂມງຈັບເວລາ

1. Press the top pusher (usually located at the 2 o'clock position) to start the chronograph. The chronograph second hand will begin to move.
2. To stop the chronograph, press the top pusher again. The chronograph hands will stop, indicating the elapsed time.

4.2 ການຕັ້ງຄ່າໂມງຈັບເວລາຄືນໃໝ່

1. After stopping the chronograph, press the bottom pusher (usually located at the 4 o'clock position) to reset the chronograph hands to their zero positions.

5. ບໍາລຸງຮັກສາ

5.1 ການຕໍ່ຕ້ານນ້ໍາ

Your AVI-8 AV-4077 watch is water-resistant up to 50 meters (5 ATM). This means it is suitable for short periods of recreational swimming, showering, or washing hands. It is NOT suitable for diving, snorkeling, or prolonged water exposure. Always ensure the crown is fully pushed in before any contact with water.

5.2 ການທໍາຄວາມສະອາດ

To maintain the appearance of your watch, wipe the case and crystal with a soft, dry cloth. For the leather strap, avoid excessive moisture and harsh chemicals. Clean with a damp cloth and allow to air dry naturally.

5.3 ການດູແລສາຍແອວ

The genuine leather strap may show signs of wear over time. To prolong its life, avoid prolonged exposure to direct sunlight, extreme temperatures, and moisture. If the strap becomes wet, dry it thoroughly before wearing.

6. ການແກ້ໄຂບັນຫາ

6.1 Watch Not Running or Intermittent Operation

• Check if the crown is fully pushed in. If it is pulled out, the watch will not run.
• The Meca-Quartz movement requires a battery. If the watch stops completely, the battery may need replacement. Contact a qualified watch technician for battery replacement.

6.2 ເຂັມໂມງໂຄຣໂນກຣາບບໍ່ໄດ້ຕັ້ງຄ່າໃໝ່ເປັນສູນ

If the chronograph hands do not return precisely to the 12 o'clock (zero) position after resetting, they may need calibration. This can sometimes occur after a battery change or impact.

1. Pull the crown out to the outermost position (time setting position).
2. Press the top pusher repeatedly to advance the chronograph second hand until it aligns with the 12 o'clock position.
3. If other chronograph sub-dials are misaligned, use the bottom pusher to adjust them to their zero positions.
4. Once all chronograph hands are aligned, push the crown back into its normal operating position.

7. ຂໍ້ມູນຈໍາເພາະ

8. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

For warranty information and customer support, please refer to the documentation included with your product packaging or visit the official AVI-8 webເວັບໄຊ. ຮັກສາຫຼັກຖານການຊື້ຂອງທ່ານສໍາລັບການຮຽກຮ້ອງການຮັບປະກັນໃດໆ.