IBO S-150 Central Heating Pump Controller User Manual

1. ຜະລິດຕະພັນເກີນview

The IBO S-150 is an electronic control unit designed for managing the circulation pump in a central heating system. Its primary function is to activate the pump when the water temperature exceeds a preset value and deactivate it when the temperature falls below that value. This intelligent control helps to optimize energy consumption and extend the operational lifespan of the pump.

ຄຸນ​ນະ​ສົມ​ບັດ​ທີ່​ສໍາ​ຄັນ​:

• Integrated Thermostat Function: Allows setting specific temperature thresholds for pump activation and deactivation.
• ຟັງຊັນຕ້ານການ freeze: Automatically activates the pump if the ambient temperature drops below 5 °C (41 °F) to prevent freezing within the system.
• ການປະຫຍັດພະລັງງານ: Prevents unnecessary pump operation, leading to reduced energy consumption.
• Extended Pump Lifespan: Reduces wear and tear on the pump by operating it only when required.
• ຕົວຊີ້ວັດ LED: Two LED displays show current temperature and set stop temperature.
• ການໂຕ້ຕອບຜູ້ເປັນມິດ: Simple button controls for setting parameters.

2. ຂໍ້ມູນຄວາມປອດໄພ

ກະລຸນາອ່ານຄໍາແນະນໍາດ້ານຄວາມປອດໄພທັງໝົດຢ່າງລະມັດລະວັງກ່ອນການຕິດຕັ້ງ ແລະການດໍາເນີນງານ. ການບໍ່ປະຕິບັດຕາມຄໍາແນະນໍາເຫຼົ່ານີ້ອາດຈະເຮັດໃຫ້ໄຟຟ້າຊ໊ອກ, ໄຟໄຫມ້, ຫຼືບາດເຈັບສາຫັດ.

• ຄວາມປອດໄພທາງໄຟຟ້າ: Installation and maintenance should only be performed by qualified personnel in accordance with local electrical codes and regulations.
• ການຕັດການເຊື່ອມຕໍ່ໄຟຟ້າ: Always disconnect the power supply to the central heating system and the controller before performing any installation, wiring, or maintenance.
• ນ​້​ໍ​າ​ແລະ​ຄວາມ​ຊຸ່ມ​: Do not expose the controller to water, excessive moisture, or extreme temperatures. Ensure the installation location is dry and protected.
• ການ​ຕັ້ງ​ພື້ນ​ທີ່​ເຫມາະ​ສົມ​: Ensure the device is properly grounded to prevent electrical hazards.
• ຄວາມສົມບູນຂອງສາຍ: Regularly inspect all cables for damage. Do not use the device if any cables are frayed or damaged.
• ການ​ນໍາ​ໃຊ້​ຈຸດ​ປະ​ສົງ​: Use the controller only for its intended purpose as a central heating pump controller.

3. ຂໍ້ກໍານົດດ້ານວິຊາການ

4. ການຕິດຕັ້ງແລະການຕິດຕັ້ງ

Before proceeding with installation, ensure the main power supply to your central heating system is turned off at the circuit breaker.

4.1. ການຕິດຕັ້ງຕົວຄວບຄຸມ

Select a suitable, dry location for mounting the controller, away from direct heat sources or excessive moisture. The controller can be mounted on a wall using appropriate fasteners (not included). Ensure sufficient space for cable connections.

4.2. ການເຊື່ອມຕໍ່ສາຍໄຟ

The IBO S-150 controller comes with three main connections:

1. ສາຍໄຟ: This cable supplies power to the controller. Plug it into a standard 230V, 50Hz electrical outlet.
2. Pump Power Cable: This cable connects the controller to your central heating circulation pump. Ensure the pump is compatible with the controller's specifications (Max load: 6A).
3. Temperature Sensor Cable: The ohmic temperature sensor should be placed in a location where it can accurately measure the water temperature of the central heating system. Typically, this is on the return pipe or a designated sensor pocket. Ensure good thermal contact for accurate readings.

ຮູບ 1: ເກີນview of the IBO S-150 controller with its connected power, pump, and sensor cables.

ຮູບທີ 2: ດ້ານລຸ່ມ view of the controller, illustrating the connection points for the power and pump cables.

After all connections are securely made, restore power to the central heating system.

5. ການດໍາເນີນງານ

The IBO S-150 controller features a simple interface with two LED displays and three control buttons.

Figure 3: Front panel of the IBO S-150 controller, showing the LED displays and control buttons.

5.1. ການເປີດເຄື່ອງເບື້ອງຕົ້ນ

Upon initial power-on, the upper LED display will show the current temperature measured by the sensor. The lower LED display will show the currently set 'stop temperature'.

5.2. ປຸ່ມຄວບຄຸມ

• ປຸ່ມເມນູ: Used to cycle through and select different settings (stop temperature, start temperature, anti-freeze function). Pressing this button allows you to enter the setting mode for each parameter.
• UP Arrow Button (▲): Used to increase the value of a selected parameter.
• DOWN Arrow Button (▼): Used to decrease the value of a selected parameter.

5.3. Setting Temperature Parameters

1. ກົດ ເມນູ button to enter the setting mode. The lower display will start flashing, indicating you can adjust the 'stop temperature'.
2. ໃຊ້ ຂຶ້ນ (▲) ແລະ ລົງ (▼) arrow buttons to set the desired temperature at which the pump should stop.
3. ກົດ ເມນູ button again to confirm the 'stop temperature' and move to the 'start temperature' setting. The lower display will flash again.
4. ໃຊ້ ຂຶ້ນ (▲) ແລະ ລົງ (▼) arrow buttons to set the desired temperature at which the pump should start. This is typically a few degrees higher than the stop temperature to prevent rapid cycling.
5. ກົດ ເມນູ button a third time to confirm the 'start temperature' and exit the setting mode. The controller will return to displaying the current and stop temperatures.

5.4. ໜ້າທີ່ຕ້ານການແຂງຕົວ

The anti-freeze function is automatically engaged. If the temperature measured by the sensor drops below 5 °C (41 °F), the pump will activate regardless of other settings to circulate water and prevent freezing. This function cannot be manually disabled.

6. ບໍາລຸງຮັກສາ

The IBO S-150 controller requires minimal maintenance to ensure optimal performance and longevity.

• ທໍາຄວາມສະອາດ: Periodically wipe the exterior of the controller with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure no liquids enter the device.
• ການກວດສອບສາຍ: Regularly check all connected cables (power, pump, sensor) for any signs of wear, damage, or loose connections. Replace damaged cables immediately.
• ການຈັດວາງເຊັນເຊີ: Ensure the temperature sensor remains securely in its intended position and maintains good thermal contact with the heating system pipe.
• ເງື່ອນໄຂສິ່ງແວດລ້ອມ: Verify that the controller's operating environment remains within the specified ambient temperature and humidity ranges.

7. ການແກ້ໄຂບັນຫາ

If you encounter issues with your IBO S-150 controller, refer to the following troubleshooting guide:

If the problem persists after attempting these solutions, please contact a qualified technician or the product support.

8. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

ສຳລັບຂໍ້ມູນການຮັບປະກັນ ແລະ ການຊ່ວຍເຫຼືອດ້ານເຕັກນິກ, ກະລຸນາອ້າງອີງເອກະສານທີ່ມາພ້ອມກັບການຊື້ຂອງທ່ານ ຫຼື ຕິດຕໍ່ຮ້ານຄ້າປີກຂອງທ່ານ. ເກັບຫຼັກຖານການຊື້ຂອງທ່ານໄວ້ສຳລັບການຮຽກຮ້ອງການຮັບປະກັນໃດໆ.

Manufacturer: IBO

ຈໍານວນສິນຄ້າ: S-150