Gioteck SC3 Wireless Pro Controller User Manual

ແນະນຳ

This manual provides detailed instructions for the setup, operation, and maintenance of your Gioteck SC3 Wireless Pro Controller. Designed for use with Nintendo Switch, PC, and mobile devices, this controller features programmable back buttons, customizable RGB lighting, and changeable magnetic thumb sticks for an enhanced gaming experience.

1. ຕັ້ງຄ່າ

1.1 ເນື້ອໃນຊຸດ

• Gioteck SC3 Wireless Pro Controller
• ສາຍສາກ USB
• Additional Magnetic Thumb Sticks (if included)
• ຄູ່ມືຜູ້ໃຊ້ (ເອກະສານນີ້)

1.2 ການສາກເຄື່ອງຄວບຄຸມ

Before initial use, fully charge the controller. Connect the supplied USB charging cable to the controller's charging port and the other end to a USB power source (e.g., Nintendo Switch dock, PC USB port, or USB wall adapter).

• ຕົວຊີ້ວັດ LED ຈະສະແດງສະຖານະການສາກໄຟ.
• ໂດຍປົກກະຕິການສາກເຕັມຈະໃຊ້ເວລາປະມານ 2-3 ຊົ່ວໂມງ.

ຮູບພາບ: ລຸ່ມ view of the Gioteck SC3 controller, highlighting the USB-C charging port located between the two textured grips.

1.3 ການຈັບຄູ່ກັບ Nintendo Switch

1. ຈາກເມນູ Nintendo Switch HOME, ເລືອກ ຜູ້ຄວບຄຸມ, ແລ້ວ ປ່ຽນ Grip/Order.
2. On the SC3 controller, press and hold the ປຸ່ມຈັບຄູ່ (usually a small button on the top or back) for a few seconds until the LED indicators begin to flash rapidly.
3. Once the controller is recognized by the Switch, the player LED(s) on the controller will illuminate solid, indicating successful pairing.
4. ກົດ ປຸ່ມ ເພື່ອຢືນຢັນ.

Note: For subsequent uses, the controller should automatically reconnect to the last paired Switch console when powered on.

1.4 Connecting to PC/Mobile (Bluetooth)

1. Ensure Bluetooth is enabled on your PC or mobile device.
2. On the SC3 controller, press and hold the ປຸ່ມຈັບຄູ່ for a few seconds until the LED indicators flash rapidly.
3. On your PC/mobile device, navigate to Bluetooth settings and search for new devices.
4. Select "Gioteck SC3" or similar from the list of available devices to pair.
5. The controller's LED will become solid upon successful connection.

1.5 Installing Magnetic Thumb Sticks

The SC3 controller features changeable magnetic thumb sticks. To replace them:

1. Gently pull the existing thumb stick straight up to remove it.
2. Align the desired magnetic thumb stick with the base and gently push it down until it snaps into place.

ຮູບພາບ: ທາງຫນ້າ view of the Gioteck SC3 controller, showcasing the magnetic thumb sticks and button layout.

2. ຄໍາແນະນໍາການດໍາເນີນງານ

2.1 ຮູບແບບປຸ່ມ

The SC3 controller features a traditional button layout. Refer to the image below for button identification.

ຮູບພາບ: ດ້ານຫນ້າເປັນມຸມ view of the Gioteck SC3 controller, displaying the full button layout including face buttons, D-pad, analog sticks, and shoulder buttons.

• ໄມ້ອະນາລັອກຊ້າຍ/ຂວາ: ສໍາລັບການເຄື່ອນໄຫວແລະການຄວບຄຸມກ້ອງຖ່າຍຮູບ.
• D-Pad: ການປ້ອນຂໍ້ມູນທິດທາງ.
• ປຸ່ມ A/B/X/Y: ປຸ່ມປະຕິບັດ.
• ປຸ່ມ L/R/ZL/ZR: ບ່າ ແລະ ປຸ່ມກະຕຸ້ນ.
• +/- ປຸ່ມ: Start/Select equivalents.
• ປຸ່ມຫນ້າທໍາອິດ: ກັບຄືນໄປຫາເມນູຫຼັກຂອງຄອນໂຊນ.
• ປຸ່ມບັນທຶກ: Takes screenshots.

2.2 Programmable Back Buttons

The SC3 controller includes programmable back buttons (M1, M2, M3, M4) for custom assignments.

ຮູບພາບ: ດ້ານຫລັງ view of the Gioteck SC3 controller, clearly showing the four programmable back buttons (M1, M2, M3, M4) and textured grips.

ຂັ້ນຕອນການຂຽນໂປຣແກຣມ:

1. ກົດຄ້າງໄວ້ ປຸ່ມໂຄງການ (refer to diagram if available, usually a small button on the back) until the LED indicator flashes.
2. ກົດ ປຸ່ມກັບຄືນ (M1, M2, M3, or M4) you wish to program. The LED will flash slowly.
3. ກົດ ປຸ່ມປ້ອນ (e.g., A, B, X, Y, L, R, ZL, ZR, D-pad direction) you want to assign to the back button.
4. ກົດ ປຸ່ມໂຄງການ again to save the assignment. The LED will stop flashing.
5. Repeat for other back buttons as desired.

To clear a programmed button, follow steps 1-2, then press the Program Button again without pressing an input button.

2.3 ການປັບແຕ່ງແສງ RGB

The controller features customizable RGB lighting. Specific instructions for changing colors or effects are typically found in the product's quick start guide or by pressing a dedicated button combination (e.g., Function + R3).

Consult the quick start guide included with your controller for precise button combinations to adjust RGB lighting.

2.4 ການຄວບຄຸມການເຄື່ອນໄຫວ

The SC3 controller supports motion controls, allowing for immersive gameplay in compatible Nintendo Switch titles. No special setup is usually required; motion controls activate automatically when supported by the game.

2.5 Audio Headset Jack

A 3.5mm audio headset jack is located on the controller for connecting compatible headsets. It includes dedicated mute and volume control buttons.

• ປະລິມານຂຶ້ນ/ລົງ: ປັບສຽງອອກ.
• ປິດສຽງ: Mute/unmute microphone input.

ຮູບພາບ: ເທິງ view of the Gioteck SC3 controller, highlighting the 3.5mm audio jack, volume controls, and mute button.

3. ບໍາລຸງຮັກສາ

3.1 ການທໍາຄວາມສະອາດ

ເພື່ອເຮັດຄວາມສະອາດເຄື່ອງຄວບຄຸມຂອງທ່ານ, ໃຫ້ໃຊ້ຜ້າອ່ອນໆ, ແຫ້ງ. ສໍາລັບຝຸ່ນ stubborn, ເລັກນ້ອຍ dampen ຜ້າ​ທີ່​ມີ​ນ​້​ໍ​າ​. ຫຼີກເວັ້ນການໃຊ້ສານເຄມີທີ່ຮຸນແຮງ, ເຄື່ອງເຮັດຄວາມສະອາດຂັດ, ຫຼືສານລະລາຍ, ເພາະວ່າສິ່ງເຫຼົ່ານີ້ສາມາດທໍາລາຍເຄື່ອງຄວບຄຸມແລະອົງປະກອບພາຍໃນ.

• Do not immerse the controller in water or any other liquid.
• Ensure all ports are dry before charging or connecting devices.

3.2 ການເກັບຮັກສາ

ເກັບຮັກສາເຄື່ອງຄວບຄຸມໄວ້ໃນບ່ອນທີ່ເຢັນ, ແຫ້ງ, ຫ່າງຈາກແສງແດດໂດຍກົງແລະອຸນຫະພູມທີ່ສຸດ. ຫຼີກເວັ້ນການວາງວັດຖຸຫນັກໃສ່ເຄື່ອງຄວບຄຸມເພື່ອປ້ອງກັນຄວາມເສຍຫາຍ.

3.3 ການດູແລຫມໍ້ໄຟ

The controller contains a rechargeable battery. To prolong battery life:

• ຫຼີກ​ລ້ຽງ​ການ​ປະ​ຈຸ​ຫມໍ້​ໄຟ​ຢ່າງ​ເຕັມ​ທີ່​ເລື້ອຍໆ​.
• Charge the controller regularly, even if not in use for extended periods (e.g., once every 3-6 months).
• Do not expose the controller to temperatures above 60°C (140°F).

4. ການແກ້ໄຂບັນຫາ

4.1 ຕົວຄວບຄຸມບໍ່ໄດ້ເຊື່ອມຕໍ່/ການຈັບຄູ່

• ກວດ​ສອບ​ຫມໍ້​ໄຟ​: ຮັບປະກັນວ່າຕົວຄວບຄຸມມີການສາກໄຟພຽງພໍ.
• ຄູ່ໃໝ່: Follow the pairing instructions in Section 1.3 or 1.4.
• ແຊກແຊງ: Move closer to the console/device and away from potential sources of wireless interference (e.g., Wi-Fi routers, other Bluetooth devices).
• ຣີເຊັດຕົວຄວບຄຸມ: Locate a small reset button (often a pinhole) on the back of the controller. Use a paperclip to press and hold it for a few seconds. Then attempt to re-pair.
• Update Console/Device Software: Ensure your Nintendo Switch, PC, or mobile device's operating system is up to date.

4.2 Buttons/Sticks Not Responding

• Re-sync: ຕັດການເຊື່ອມຕໍ່ ແລະເຊື່ອມຕໍ່ຕົວຄວບຄຸມຄືນໃໝ່.
• ສະອາດ: ໃຫ້ແນ່ໃຈວ່າບໍ່ມີສິ່ງເສດເຫຼືອຕິດຢູ່ອ້ອມປຸ່ມ ຫຼື ໄມ້.
• Test in another game/menu: Determine if the issue is specific to a game or system-wide.
• ຣີເຊັດຕົວຄວບຄຸມ: Perform a hard reset as described above.

4.3 Motion Controls Not Working

• ຄວາມເຂົ້າກັນໄດ້ຂອງເກມ: Verify that the game you are playing supports motion controls.
• Recalibrate: On Nintendo Switch, you can recalibrate motion controls in the system settings.
• ຣີເຊັດຕົວຄວບຄຸມ: ປະຕິບັດການປັບຍາກ.

5. ຂໍ້ມູນຈໍາເພາະ

6. ຂໍ້ມູນການຮັບປະກັນ

The Gioteck SC3 Wireless Pro Controller comes with a manufacturer's warranty. For specific details regarding warranty coverage, duration, and claims process, please refer to the warranty card included with your product or visit the official Gioteck webເວັບໄຊ.

ກະລຸນາຮັກສາຫຼັກຖານການຊື້ຂອງທ່ານໄວ້ເພື່ອຈຸດປະສົງການຮັບປະກັນ.

7. ການຊ່ວຍເຫຼືອລູກຄ້າ

If you encounter any issues or have questions not covered in this manual, please contact Gioteck customer support. Contact information can typically be found on the product packaging or the official Gioteck webເວັບໄຊ.

Gioteck Official Webເວັບໄຊ: www.gioteck.com