ຄູ່ມືຜູ້ໃຊ້ເຄື່ອງສັງເຄາະສຽງເບສແບບອະນາລັອກ Behringer TD-3-MO-AM

ແຜນຜັງດ້ານ ໜ້າ

Below is an image illustrating the front panel controls and connections of the TD-3-MO-AM synthesizer. Familiarize yourself with these components before operation.

ຮູບທີ 1: Front panel of the Behringer TD-3-MO-AM Analog Bass Line Synthesizer. This image displays all knobs, buttons, and input/output jacks, including controls for Tune, Cutoff, Resonance, Envelope, Decay, Accent, Tempo, Wave, Track/Pattern Group, Mode, Gate, Slide Time, Sweep Speed, Filter FM, Volume, and various input/output ports.

2.1 ການຫຸ້ມຫໍ່ແລະການກວດກາ

Carefully remove the synthesizer from its packaging. Inspect the unit for any signs of damage during transit. Retain the original packaging for future transport or storage.

2.2 ການເຊື່ອມຕໍ່ພະລັງງານ

Connect the provided power adapter to the DC IN port on the rear panel of the TD-3-MO-AM. Plug the adapter into a suitable power outlet. Ensure the power switch is in the OFF position before connecting power.

2.3 ສຽງອອກ

Connect the AUDIO OUT jack (typically a 1/4" TS or TRS jack, though not explicitly listed in specs, common for synths) on the rear panel to your mixer, audio interface, or amplifier using a standard audio cable. For headphone monitoring, use the PHONES output.

2.4 ການເຊື່ອມຕໍ່ MIDI ແລະ USB

The TD-3-MO-AM supports MIDI and USB connectivity for integration with other musical equipment or a computer.

• ກາງ/ອອກ: Use standard 5-pin DIN MIDI cables to connect to other MIDI devices for sequencing or control.
• USB: Connect the USB-A port (as per specifications) to your computer for MIDI over USB and firmware updates.

2.5 ການເຊື່ອມຕໍ່ CV/ປະຕູ

The synthesizer features various CV (Control Voltage) and Gate inputs/outputs for integration with modular synthesizers and other analog gear.

• ACCENT IN, SLIDE IN, GATE IN, CV IN: These inputs allow external control over corresponding parameters.
• SYNC IN, ACCENT OUT, GATE OUT, CV OUT, FILTER OUT: These outputs provide control signals to other devices.

3.1 ການເປີດ/ປິດ

To power on, ensure all connections are secure, then flip the power switch to the ON position. To power off, flip the switch to the OFF position and disconnect the power adapter.

3.2 Sound Generation Basics

The TD-3-MO-AM generates sound using an analog oscillator. Adjust the ປບັ, ຕັດ, ຄວາມຮັບຜິດຊອບ, ບໍລິສັດຜະລິດໄຟຟ້າ ENVachinE, ເສື່ອມໂຊມ, ແລະ ACCENT knobs to shape the sound. The ຄື້ນ switch selects between sawtooth and square waveforms.

3.3 ການປະຕິບັດລໍາດັບ

The built-in 16-step sequencer allows for programming bass lines. Use the ໂໝດ switch to select between WRITE and PLAY modes. In WRITE mode, you can input notes and parameters for each step. In PLAY mode, the sequencer will playback the programmed pattern.

• ຂຽນ: For creating and editing patterns.
• ຫຼິ້ນ: For playing back patterns.
• TRK/PATT: Selects between Track and Pattern modes for sequencing.

ປັບ TEMPO knob to control the playback speed of the sequencer.

3.4 ໂຕແທນ

The arpeggiator can generate rhythmic patterns from held notes. Refer to the detailed manual for specific arpeggiator modes and controls.

3.5 Filter and Overdrive

The 4-pole resonant lowpass filter is a key component of the TD-3-MO-AM's sound. Use the ຕັດ ແລະ ຄວາມຮັບຜິດຊອບ knobs to sculpt the tone. The ຫຼາຍເກີນໄປ control adds distortion and grit to the sound.

4.1 ການທໍາຄວາມສະອາດ

To clean the unit, use a soft, dry cloth. Do not use abrasive cleaners, waxes, or solvents. Avoid spraying liquids directly onto the unit.

4.2 ການເກັບຮັກສາ

When not in use for extended periods, store the synthesizer in a cool, dry place, away from direct sunlight and extreme temperatures. It is recommended to use the original packaging for storage.

4.3 ການອັບເດດເຟີມແວ

ກວດເບິ່ງ Behringer ເປັນໄລຍະ website for firmware updates. Updates can provide new features, bug fixes, and performance improvements. Follow the instructions provided with the firmware update package carefully.

5.1 ບໍ່ມີສຽງອອກ

• ກວດໃຫ້ແນ່ໃຈວ່າອະແດັບເຕີໄຟເຊື່ອມຕໍ່ຢ່າງປອດໄພ ແລະ ໜ່ວຍດັ່ງກ່າວເປີດຢູ່.
• Check all audio cable connections from the TD-3-MO-AM to your mixer/interface/ampມີຊີວິດຊີວາ.
• Verify that the VOLUME knob on the TD-3-MO-AM is turned up.
• Confirm that your mixer/interface/amplifier is powered on and its input levels are correctly set.
• If using headphones, ensure they are properly plugged into the PHONES jack and the volume is adequate.

5.2 ລໍາດັບບໍ່ໄດ້ຫຼິ້ນ

• ຮັບປະກັນ ໂໝດ switch is set to PLAY.
• Verify that a pattern has been programmed and is selected.
• ກວດເບິ່ງ TEMPO knob; it might be set too low.
• If syncing externally, ensure the SYNC IN connection is active and receiving a valid clock signal.

5.3 ບັນຫາການເຊື່ອມຕໍ່ MIDI/USB

• Ensure correct MIDI cable connections (MIDI OUT to MIDI IN, MIDI IN to MIDI OUT).
• For USB, verify the USB cable is securely connected to both the synthesizer and your computer.
• Check your computer's device manager or audio/MIDI settings to confirm the TD-3-MO-AM is recognized.
• Install any necessary drivers if prompted by your operating system (usually class-compliant, but check Behringer support).

7.1 ການຮັບປະກັນຜະລິດຕະພັນ

Behringer products typically come with a limited warranty covering manufacturing defects. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Behringer webເວັບໄຊ. ຮັກສາຫຼັກຖານການຊື້ຂອງທ່ານສໍາລັບການຮ້ອງຂໍການຮັບປະກັນ.

7.2 ສະຫນັບສະຫນູນລູກຄ້າ

For technical assistance, troubleshooting beyond this manual, or service inquiries, please contact Behringer customer support. You can find contact information and additional resources on the official Behringer webເວັບໄຊ: www.behringer.com.

For protection plans, refer to the options available at the point of purchase, such as those offered by Amazon:

• ແຜນການປົກປ້ອງ 3 ປີ
• ແຜນການປົກປ້ອງ 4 ປີ
• ສໍາເລັດການປົກປ້ອງ (ແຜນການປະຈໍາເດືອນ)