Lepro LE 50ft RGB 5050 LED Strip Lights ຄູ່ມືຄໍາແນະນໍາ

ແນະນຳ

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Lepro LE 50ft RGB 5050 LED Strip Lights. Please read this manual thoroughly before installation and use to ensure proper function and safety. Keep this manual for future reference.

ຄໍາແນະນໍາຄວາມປອດໄພ

• ໃຫ້ແນ່ໃຈວ່າການປິດການສະຫນອງພະລັງງານກ່ອນທີ່ຈະຕິດຕັ້ງຫຼືບໍາລຸງຮັກສາ.
• ຜະລິດຕະພັນນີ້ຖືກອອກແບບມາສໍາລັບການນໍາໃຊ້ພາຍໃນເຮືອນເທົ່ານັ້ນ. ຫຼີກເວັ້ນການສໍາຜັດກັບນ້ໍາຫຼືຄວາມຊຸ່ມຊື່ນສູງ.
• Do not connect the LED strip to the power supply while it is still coiled on the reel. Unroll the strip completely before powering on to prevent overheating.
• Use only the provided 12V ETL-listed power adapter. Using an incompatible power supply may damage the product and void the warranty.
• Do not bend the LED strip at sharp angles (less than 90 degrees) to avoid damaging the circuit board or LEDs.
• ຮັກສາໃຫ້ໄກຈາກເດັກນ້ອຍ.
• If any damage is observed on the strip or power adapter, discontinue use immediately and contact customer support.

ເນື້ອໃນຊຸດ

Image: The complete package contents including two rolls of LED strip lights, a remote control, a power adapter, and fixing clips with screws.

ກະ​ລຸ​ນາ​ກວດ​ສອບ​ວ່າ​ລາຍ​ການ​ທັງ​ຫມົດ​ທີ່​ລະ​ບຸ​ໄວ້​ຂ້າງ​ລຸ່ມ​ນີ້​ແມ່ນ​ລວມ​ຢູ່​ໃນ​ຊຸດ​ຂອງ​ທ່ານ​:

• 2 x 24.6ft (total 50ft) RGB 5050 LED Strip Lights
• 1 x IR Remote Controller (44-key)
• 1 x 12V ETL-listed Power Adapter
• 1 x ກ່ອງຄວບຄຸມ
• ການແກ້ໄຂຄລິບແລະ screws
• ຄູ່ມືຜູ້ໃຊ້ (ເອກະສານນີ້)

ຂໍ້ມູນຈໍາເພາະ

ການຕິດຕັ້ງ & ການຕິດຕັ້ງ

Follow these steps for proper installation of your LED strip lights:

1. ການ​ກະ​ກຽມ​ຫນ້າ​ດິນ​:

   Before attaching the LED strip, ensure the installation surface is clean, dry, and smooth. Wipe the surface with a clean cloth to remove dust or debris. This ensures optimal adhesion of the 3M adhesive backing.

   

   Image: A hand wiping a wooden surface with a cloth, illustrating the first step of surface preparation.

2. ເຊື່ອມ​ຕໍ່​ອົງ​ປະ​ກອບ​:

   Connect the 4-pin connector from the LED strip to the control box. Ensure the arrow mark on the strip's connector aligns with the arrow mark on the control box. Then, connect the DC wire from the power adapter to the control box. Finally, plug the power adapter into a standard electrical outlet.

   

   Image: A visual guide demonstrating how to connect the DC wire to the control box and the 4-pin connector to the LED strip, emphasizing arrow alignment.

   ສຳຄັນ: Ensure the "arrow" mark on the LED strip connector and the "12V" mark on the control box are on the same side for correct polarity.

   

   Image: Detail of the RGB light strip, highlighting the 10mm 4-pin connector and the strong 3M self-adhesive backing for installation.

3. ຕິດແຖບ LED:

   Peel off the protective backing from the 3M adhesive on the back of the LED strip. Carefully press the strip onto the prepared surface, applying firm and even pressure along its entire length. For added security, use the included fixing clips and screws at regular intervals, especially around corners or areas with less adhesion.

   

   Image: A hand demonstrating how to peel and attach the LED strip to a surface, showing the adhesive backing.

4. ການກະກຽມການຄວບຄຸມໄລຍະໄກ:

   Before using the remote control, pull out the transparent plastic chip from the battery compartment. This activates the battery.

   

   Image: A close-up showing a hand pulling the transparent plastic chip from the remote control, indicating battery activation.

ວິດີໂອສາທິດການຕິດຕັ້ງ

ການດໍາເນີນງານ

Your LED strip lights are controlled by the included 44-key IR remote control. Point the remote directly at the IR receiver on the control box for optimal response.

ຮູບພາບ: A ລາຍລະອຽດ view of the 44-key remote control, showing buttons for power, brightness adjustment, RGB color selection, 6 DIY color buttons, and various dynamic modes like Jump, Fade, Quick, Slow, and Auto.

• ເປີດ/ປິດ: ກົດ red power button to turn the lights on or off.
• ການປັບຄວາມສະຫວ່າງ: ໃຊ້ ປຸ່ມລູກສອນຂຶ້ນ ແລະ ລົງ (above the R, G, B, W buttons) to increase or decrease brightness.
• ການເລືອກສີ: ກົດອັນໃດອັນນຶ່ງ 20 color buttons to select a static color.
• ສີ DIY:
  1. ກົດປຸ່ມ ໜຶ່ງ ໃນ DIY1-DIY6 buttons.
  2. ໃຊ້ RGB up/down arrows to adjust the intensity of Red, Green, and Blue to create your desired custom color.
  3. Press the same DIY button again to save the custom color.
• ໂໝດໄດນາມິກ:
  • JUMP3 / JUMP7: ໝຸນວຽນຜ່ານ 3 ຫຼື 7 ສີດ້ວຍຜົນກະທົບການກະໂດດ.
  • ຈາງລົງ3 / ຈາງລົງ7: ຈາງລົງລະຫວ່າງ 3 ຫຼື 7 ສີ.
  • ໄວ / ຊ້າ: Adjusts the speed of dynamic modes.
  • ອັດຕະໂນມັດ: Cycles through all available dynamic modes.
  • ກະແສໄຟຟ້າ: Flashes through colors.

ບໍາລຸງຮັກສາ

• ທໍາຄວາມສະອາດ: Ensure the power is off and unplugged before cleaning. Gently wipe the LED strip with a dry, soft cloth. Do not use liquid cleaners or abrasive materials.
• ການເກັບຮັກສາ: If storing the lights for an extended period, ensure they are clean and dry. Store in a cool, dry place away from direct sunlight.
• ການຍຶດຕິດ: If the adhesive begins to lose its stickiness, you can reinforce the strip with additional fixing clips or a suitable adhesive tape (not included).

ການແກ້ໄຂບັນຫາ

ການຮັບປະກັນ & ສະຫນັບສະຫນູນ

Lepro products are designed for quality and reliability. For warranty information, technical support, or any questions regarding your LED strip lights, please contact Lepro customer service through the retailer where the product was purchased or visit the official Lepro webເວັບໄຊ.

Please have your model number (410105-RGB-US) and purchase details ready when contacting support.