ຄູ່ມືການໃຊ້ງານ Kia Mobility KIT-TIRE (ລຸ້ນ 52933-2Y000)

ແນະນຳ

This manual provides essential instructions for the safe and effective operation, maintenance, and troubleshooting of your Kia Mobility KIT-TIRE (Model 52933-2Y000) tire compressor. Please read this manual thoroughly before using the product and retain it for future reference. Always refer to your vehicle's owner's manual for specific tire pressure recommendations and emergency procedures.

ຂໍ້ມູນຄວາມປອດໄພທີ່ສໍາຄັນ

• Do not use for sidewall punctures: This device is designed for temporary repair of tread punctures only. It is not suitable for punctures on the tire sidewall or for significant tire damage.
• ຫຼີກ​ລ້ຽງ​ການ​ຮ້ອນ​ເກີນ​ໄປ​: Continuous operation can cause the compressor to overheat. Allow the unit to cool down if it becomes excessively hot during use.
• ປະລິມານທີ່ເຫມາະສົມtage: Ensure the compressor is connected to a 12-volt DC power source, typically your vehicle's accessory outlet.
• ເດັກ​ນ້ອຍ​ແລະ​ສັດ​ລ້ຽງ​: Keep the compressor and its components away from children and pets.
• ການປົກປ້ອງຕາ: ໃສ່ເຄື່ອງປ້ອງກັນຕາທີ່ເໝາະສົມໃນເວລາເປີດເຄື່ອງອັດ.
• Vehicle stability: Ensure your vehicle is parked on a level surface with the parking brake engaged before attempting any tire inflation.
• ຄວາມດັນຢາງລົດ: Always inflate tires to the pressure specified in your vehicle's owner's manual or on the tire placard. Over-inflation can be dangerous.

For detailed visual instructions, refer to the diagram below:

ຮູບພາບ 1: ດ້ານຫນ້າ view of the Kia Mobility KIT-TIRE compressor, illustrating connection points, power switch, and operational steps.

ຕັ້ງຄ່າ

1. Prepare the vehicle: ຈອດລົດຂອງທ່ານໄວ້ເທິງພື້ນຜິວທີ່ຮາບພຽງ ແລະ ໝັ້ນຄົງ. ຢຽບເບກມື ແລະ ດັບເຄື່ອງຈັກ.
2. Locate the compressor: Remove the Kia Mobility KIT-TIRE compressor from its storage location.
3. Connect to tire valve: Unscrew the valve cap from the tire. Firmly screw the compressor's air hose connector onto the tire valve stem until secure.
4. ເຊື່ອມຕໍ່ກັບພະລັງງານ: Insert the compressor's power plug into your vehicle's 12V accessory outlet (cigarette lighter socket). Ensure the vehicle's ignition is in the "ACC" or "ON" position, or the engine is running, as required by your vehicle.

ຄໍາແນະນໍາການດໍາເນີນງານ

1. Initial Pressure Check: Before turning on the compressor, observe the current tire pressure reading on the integrated gauge.
2. ອັດຕາເງິນເຟີ້ເລີ່ມຕົ້ນ: Flip the power switch on the compressor to the "ON" position. The compressor will begin to inflate the tire.
3. ຕິດຕາມຄວາມກົດດັນ: Continuously monitor the pressure gauge. Inflate the tire to the recommended pressure (e.g., 2.0-2.8 bar / 30-40 psi, or as specified in your vehicle's manual).
4. ຢຸດອັດຕາເງິນເຟີ້: Once the desired pressure is reached, immediately switch the compressor to the "OFF" position.
5. ຕັດການເຊື່ອມຕໍ່: Unscrew the air hose connector from the tire valve and replace the valve cap. Disconnect the power plug from the vehicle's 12V outlet.
6. Post-Inflation Driving (for temporary sealant use): If using the compressor with tire sealant for a temporary repair, drive the vehicle immediately for a short distance (e.g., 10 km / 6 miles) at a moderate speed (e.g., 20-80 km/h or 15-50 mph) to allow the sealant to distribute evenly.
7. Re-check Pressure: After driving, re-check the tire pressure. If the pressure has dropped significantly, the repair may not be effective, and professional assistance is required.

ບໍາລຸງຮັກສາ

• ທໍາຄວາມສະອາດ: Wipe the exterior of the compressor with a damp ຜ້າ. ຫ້າມໃຊ້ສານເຄມີທີ່ຮຸນແຮງ ຫຼືຈຸ່ມຫົວໜ່ວຍໃນນ້ຳ.
• ການເກັບຮັກສາ: Store the compressor in a cool, dry place, away from direct sunlight and extreme temperatures. Ensure the hose and power cord are neatly coiled to prevent damage.
• ການກວດກາ: Periodically inspect the air hose, power cord, and connectors for any signs of wear, cracks, or damage. Do not use the unit if any components are damaged.

ການແກ້ໄຂບັນຫາ

• ເຄື່ອງອັດອາກາດບໍ່ເປີດ:
  • Ensure the power plug is fully inserted into the 12V outlet.
  • Check the vehicle's 12V outlet fuse.
  • Verify the vehicle's ignition is in the correct position (ACC or ON).
• Slow inflation or no inflation:
  • Ensure the air hose connector is securely attached to the tire valve.
  • Check for leaks in the air hose or connections.
  • Verify the tire valve stem is not damaged.
  • If the tire has a large puncture or sidewall damage, the compressor may not be able to inflate it.
• Compressor overheats:
  • Allow the unit to cool down for at least 10-15 minutes before resuming operation.
  • Avoid continuous operation for extended periods.
• ການອ່ານຄວາມກົດດັນທີ່ບໍ່ຖືກຕ້ອງ:
  • Ensure the compressor is on a stable surface.
  • Compare the reading with a known accurate tire pressure gauge if available.

ຂໍ້ມູນຈໍາເພາະ

For additional technical details, refer to the product label shown below:

ຮູບພາບ 2: ກັບຄືນໄປບ່ອນ view of the Kia Mobility KIT-TIRE compressor, showing model, power, and manufacturing details.

ຂໍ້ມູນການຮັບປະກັນ

Specific warranty details for the Kia Mobility KIT-TIRE (Model 52933-2Y000) are not provided in this manual. Please refer to the warranty documentation included with your purchase or contact your authorized Kia dealer or the product seller for comprehensive warranty information.

ການຊ່ວຍເຫຼືອລູກຄ້າ

For technical assistance, service, or inquiries regarding your Kia Mobility KIT-TIRE, please contact your authorized Kia service center or the retailer from whom you purchased the product. Provide your model number (52933-2Y000) when seeking support to ensure accurate assistance.