1. ບົດແນະນຳ
This manual provides essential information for the safe and effective use of Alpha WS-809 Water-Soluble Solder Paste. Please read this manual thoroughly before use to ensure optimal performance and safety.
2. ຜະລິດຕະພັນເກີນview
The Alpha WS-809 is a high-quality water-soluble solder paste, specifically formulated with Sn63Pb37 alloy. It is designed for use in the assembly of Printed Circuit Boards (PCBs) across various applications, including handheld electronic devices, computers, consumer electronics, network servers, automotive systems, medical equipment, and military equipment.
Figure 1: Alpha WS-809 Water-Soluble Solder Paste, showing both jar and tube packaging options. The jar is labeled "ALPHA Solder Paste" with "NO-CLEAN" visible, and the tube also has similar branding.
2.1 ລັກສະນະທີ່ສໍາຄັນ
- Alloy Composition: Sn63Pb37 (Tin 63%, Lead 37%)
- ປະເພດ: Water-Soluble
- ການຫຸ້ມຫໍ່: Available in 500g Jar (as per product details)
- ຄໍາຮ້ອງສະຫມັກ: Suitable for a wide range of PCB assembly processes.
3. ການເກັບຮັກສາແລະການຈັດການ
Proper storage and handling are crucial for maintaining the quality and performance of WS-809 solder paste.
3.1 ຄໍາແນະນໍາການເກັບຮັກສາ
- Store in a cool, dry environment, ideally refrigerated at 0-10°C (32-50°F).
- Keep containers tightly sealed to prevent moisture absorption and solvent evaporation.
- Do not freeze the solder paste.
3.2 ຂໍ້ຄວນລະວັງໃນການຈັດການ
- Allow the solder paste to reach room temperature (20-25°C / 68-77°F) for at least 4 hours before use. Do not force warm.
- Stir the paste gently before use to ensure homogeneity, especially after prolonged storage.
- Use appropriate personal protective equipment (PPE), including gloves and eye protection, when handling.
- Avoid direct skin contact and inhalation of fumes. Work in a well-ventilated area.
4. ຄໍາແນະນໍາການດໍາເນີນງານ
Follow these guidelines for optimal application and reflow of WS-809 solder paste.
4.1 ຄໍາຮ້ອງສະຫມັກ
WS-809 solder paste is typically applied using stencil printing. Ensure the stencil is clean and properly aligned with the PCB pads.
- Stencil Type: Stainless steel or nickel stencils are recommended.
- Squeegee Speed: Adjust speed based on stencil aperture size and paste viscosity, typically 25-100 mm/sec.
- Print Pressure: Apply sufficient pressure to ensure clean wipe of the stencil, avoiding excessive pressure that can cause paste bleed.
- ເງື່ອນໄຂສະພາບແວດລ້ອມ: Maintain a controlled environment with temperature between 20-25°C (68-77°F) and relative humidity between 40-60%.
4.2 Reflow Profile
A proper reflow profile is critical for achieving strong solder joints and minimizing defects. The following is a general guideline; specific profiles may vary based on oven type, PCB design, and component mass.
- Preheat Zone: Gradually increase temperature from room temperature to 150-180°C (302-356°F) over 60-120 seconds. This activates the flux and evaporates solvents.
- Soak Zone: Maintain temperature between 180-200°C (356-392°F) for 60-90 seconds. This allows temperature equalization across the PCB.
- Reflow Zone: Peak temperature should be 215-225°C (419-437°F) for 20-40 seconds above liquidus (183°C for Sn63Pb37).
- ເຂດຄວາມເຢັນ: Rapid cooling is recommended to achieve fine grain structure and strong joints, typically 3-6°C/second.
5. Post-Reflow Cleaning
As a water-soluble solder paste, WS-809 residues are designed to be easily removed with deionized water.
- ວິທີທໍາຄວາມສະອາດ: Spray or immersion cleaning with deionized water at 40-60°C (104-140°F).
- ເວລາລ້າງ: Typically 2-5 minutes, depending on residue amount and cleaning equipment.
- ການອົບແຫ້ງ: Ensure PCBs are thoroughly dried after cleaning to prevent corrosion.
6. ການບໍາລຸງຮັກສາແລະການກໍາຈັດ
6.1 ການບໍາລຸງຮັກສາອຸປະກອນ
Regular cleaning of stencil printing equipment and reflow ovens is essential to prevent contamination and ensure consistent performance. Clean stencils immediately after use to prevent paste drying in apertures.
6.2 ການຖິ້ມຂີ້ເຫຍື້ອ
Dispose of unused solder paste and contaminated materials in accordance with local, state, and federal environmental regulations. Consult the product's Safety Data Sheet (SDS) for specific disposal information.
7. ການແກ້ໄຂບັນຫາ
Common issues and their potential solutions when working with solder paste:
| ບັນຫາ | ສາເຫດທີ່ເປັນໄປໄດ້ | ການແກ້ໄຂ |
|---|---|---|
| Solder Balls | Excessive preheat, too rapid heating, insufficient drying, poor stencil release. | Adjust preheat profile, ensure proper drying, optimize stencil printing parameters. |
| Bridging/Shorts | Too much paste deposition, paste slump, misalignment, insufficient cooling. | Reduce aperture size, optimize print pressure, ensure proper alignment, increase cooling rate. |
| Insufficient Wetting | Contaminated pads, incorrect reflow profile (too low peak temp or insufficient time above liquidus). | Ensure clean PCBs, adjust reflow profile to achieve proper peak temperature and time. |
| Voiding | Excessive flux, trapped volatiles, improper reflow profile. | Optimize reflow profile, especially preheat and soak zones, to allow proper volatile escape. |
8. ຂໍ້ມູນຈໍາເພາະ
| ຄຸນລັກສະນະ | ມູນຄ່າ |
|---|---|
| ຊື່ຜະລິດຕະພັນ | WS-809 Water-Soluble Solder Paste |
| ໂລຫະປະສົມ | Sn63Pb37 |
| ໝາຍເລກຕົວແບບ | 89.8-3-M18 |
| ນ້ຳໜັກ | 500g (Jar) / 1 Pound (as per product data) |
| ຜູ້ຜະລິດ | HISCO (as per product data) |
| ວັນທີທີ່ມີໃຫ້ທໍາອິດ | ວັນທີ 23 ມິຖຸນາ 2022 |
| ASIN | B072XSMZ1M |
9. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ
Alpha products are manufactured to high-quality standards. For specific warranty information, please refer to the official Alpha webເວັບໄຊ ຫຼືຕິດຕໍ່ຜູ້ຈັດຈໍາໜ່າຍທີ່ໄດ້ຮັບອະນຸຍາດຂອງທ່ານ.
For technical support, product inquiries, or to report issues, please contact Alpha customer service or your local representative. Always provide the product model number (89.8-3-M18) and lot number (found on the product packaging) when seeking support.
