EasyMote Universal Big Button TV Remote

2.1 ລັກສະນະທີ່ສໍາຄັນ

• ການຄວບຄຸມອຸປະກອນຄູ່: Controls both your TV and Cable Box (IR) with a single remote.
• ການ​ອອກ​ແບບ​ງ່າຍ​ດາຍ​: Features 6 large, bright, backlit buttons for basic TV control.
• Clear Text: Buttons have clear and big text for easy visibility, even in low light conditions.
• ສາຍແຂນ: Includes a strong, comfortable wrist strap to prevent misplacement.
• Universal Library: Equipped with a 'Quick Search' function to scan for TV codes quickly.
• ຮູບແບບການຮຽນຮູ້: Allows programming of each button to a custom command from your original TV or Cable Box remote.

2.2 ອົງປະກອບ

• EasyMote DT-R08W Remote Control
• Wrist Strap (pre-attached)
• ຄູ່ມືແນະ ນຳ (ເອກະສານນີ້)

Note: 2 AA batteries are required and not included.

2.3 ຜະລິດຕະພັນ Views

ດ້ານໜ້າ view of the EasyMote remote, showing the large, green backlit buttons and attached wrist strap.

ຫຼາຍ views of the EasyMote remote, illustrating its ergonomic design and battery compartment on the back.

Close-up of a hand holding the EasyMote, highlighting the bright, green backlit buttons for enhanced visibility.

3.1 ການຕິດຕັ້ງຫມໍ້ໄຟ

1. Locate the battery compartment on the back of the EasyMote remote.
2. ເລື່ອນຝາປິດແບັດເຕີຣີລົງລຸ່ມເພື່ອເປີດ.
3. ໃສ່ແບັດເຕີຣີ AA 2 ກ້ອນ, ຮັບປະກັນວ່າຂົ້ວ (+ ແລະ -) ຖືກຕ້ອງຕາມທີ່ລະບຸໄວ້ພາຍໃນຊ່ອງ.
4. ເລື່ອນຝາປິດແບັດເຕີຣີຄືນໃສ່ບ່ອນເກົ່າຈົນກວ່າມັນຈະກົດຢ່າງປອດໄພ.

3.2 Programming the EasyMote

The EasyMote can be programmed using two methods: Quick Search (Auto-Scan) or Learning Mode (from your original remote).

Method 1: Quick Search (Auto-Scan)

This method allows the EasyMote to automatically scan for compatible TV codes.

1. Ensure your TV is turned ON.
2. On the EasyMote, press and hold the ປິດສຽງ ແລະ CH+ buttons simultaneously for approximately 5 seconds until the red indicator light stays on. This indicates programming mode.
3. While in programming mode, repeatedly press the CH- button. The remote will cycle through pre-programmed codes. Observe your TV screen.
4. When your TV changes channels, immediately press the ປິດສຽງ button on the EasyMote to lock in the code. The red indicator light will turn off.
5. Test all buttons (ON/OFF, VOL+, VOL-, CH+, CH-, MUTE) to verify full functionality. If some buttons do not work, repeat the process as the remote may have found a partial match.

Method 2: Learning Mode (from Original Remote)

This method is ideal for programming specific functions from your existing TV or Cable Box remote, especially for cable box channel control.

1. Place the EasyMote and your original remote control on a flat surface, pointing their IR emitters directly at each other, about 2 inches apart.
2. On the EasyMote, press and hold the ປິດສຽງ ແລະ VOL+ buttons simultaneously for approximately 5 seconds until the red indicator light stays on. This indicates learning mode.
3. Press the button on the EasyMote that you wish to program (e.g., ON/OFF). The red indicator light will start blinking slowly.
4. On your original remote, press and hold the corresponding button (e.g., ON/OFF). The EasyMote's red indicator light will blink rapidly, then stay solid, indicating successful learning.
5. Repeat steps 3 and 4 for all other buttons you wish to program (VOL+, VOL-, CH+, CH-, MUTE).
6. Once all desired buttons are programmed, press and hold the ປິດສຽງ ແລະ VOL- buttons simultaneously on the EasyMote until the red indicator light turns off. This saves the learned commands and exits learning mode.
7. Test all programmed buttons to ensure they function correctly.