IBO OHI 25-60/180 Circulation Pump User Manual

1. ຜະລິດຕະພັນເກີນview

The IBO OHI 25-60/180 circulation pump, also known as a heating pump, facilitates the movement of heating water within a heating system. This pump model features a manual 3-speed regulator, allowing for system adaptation. It is suitable for use in heating and air conditioning systems with fluid temperatures ranging from +2°C to +110°C.

ຄຸນ​ນະ​ສົມ​ບັດ​ທີ່​ສໍາ​ຄັນ​ປະ​ກອບ​ມີ​:

• Manual 3-speed regulator for optimal system adaptation.
• Suitable for heating and air conditioning systems with fluid temperatures from +2°C to +110°C.
• Constructed with a ceramic shaft, graphite radial bearing, stainless steel bearing plate and rear pot, and a grey cast iron pump housing.
• ການອອກແບບທີ່ກະທັດຮັດສໍາລັບການຕິດຕັ້ງງ່າຍ.
• ການດໍາເນີນງານງຽບ.

Image 1: IBO OHI 25-60/180 Circulation Pump. This image displays the orange-colored pump unit with its black control panel, showing the speed selector and technical specifications. Two black rubber seals are visible at the bottom.

2. ຂໍ້ມູນຄວາມປອດໄພ

Read all instructions carefully before installation and operation. Failure to follow these instructions may result in electric shock, fire, or serious injury.

• ຄວາມປອດໄພທາງໄຟຟ້າ: Ensure the power supply is disconnected before any installation, maintenance, or repair work. All electrical connections must be performed by a qualified electrician in accordance with local regulations. The pump requires a 230V, 50Hz power supply.
• ອຸນຫະພູມນ້ໍາ: The pump handles fluid temperatures between +2°C and +110°C. Exercise caution when working with hot water to prevent burns.
• ຄວາມກົດດັນ: The maximum operating pressure is 10 bar. Ensure the system components can withstand this pressure.
• ສະພາບແວດລ້ອມການຕິດຕັ້ງ: Install the pump in a dry, well-ventilated area, protected from frost and direct weather exposure.
• ອຸປະກອນປ້ອງກັນສ່ວນບຸກຄົນ: Always wear appropriate personal protective equipment (e.g., gloves, safety glasses) during installation and maintenance.

3. ຄູ່ມືການຕິດຕັ້ງ

Proper installation is crucial for the pump's efficient and safe operation.

3.1 ການກວດສອບການຕິດຕັ້ງກ່ອນ

• Verify that the pump's specifications (voltage, frequency, pressure) match your system requirements.
• Ensure the installation location provides adequate space for mounting and future maintenance.
• Confirm that the piping system is clean and free of debris.

3.2 ການຕິດຕັ້ງປັ໊ມ

1. The pump has an installation length of 180 mm. Ensure sufficient space between pipe connections.
2. Install the pump in the return line of the heating system, if possible, to extend its lifespan by operating at lower temperatures.
3. Ensure the motor shaft is horizontal to allow for proper lubrication of the bearings.
4. Use the provided seals (gaskets) to ensure a watertight connection to the piping. The connection diameter is 1 1/2"/1".
5. Tighten all connections securely but avoid over-tightening.

3.3 ການເຊື່ອມຕໍ່ໄຟຟ້າ

1. ໃຫ້ແນ່ໃຈວ່າແຫຼ່ງຈ່າຍໄຟຫຼັກຖືກປິດຢູ່ທີ່ເບຣກເກີ.
2. Connect the pump to a 1 x 230 V, 50 Hz power supply.
3. The pump has an IP44 protection rating. Ensure the electrical connections are protected from moisture.
4. Follow the wiring diagram provided on the pump's terminal box cover.
5. ຮັບປະກັນການໃສ່ພື້ນດິນທີ່ເຫມາະສົມ.

3.4 ການຕື່ມ ແລະ ການລະບາຍອາກາດຂອງລະບົບ

1. After installation, fill the heating system with water.
2. Vent the system thoroughly to remove any trapped air. Air in the system can cause noise and reduce pump efficiency.
3. The pump may have a manual vent screw; open it carefully until water flows out, then close it.

4. ຄໍາແນະນໍາການດໍາເນີນງານ

The IBO OHI 25-60/180 pump features a manual 3-speed selector to adjust performance.

4.1 ການເລີ່ມຕົ້ນເບື້ອງຕົ້ນ

1. Ensure the system is filled with water and properly vented.
2. Turn on the main power supply to the pump.
3. Select a speed setting using the rotary switch on the pump's control panel.

4.2 ການຕັ້ງຄ່າຄວາມໄວ

The pump offers three speed levels, each with different power consumption, maximum flow rate (Q max), and maximum head (H max):

• ລະດັບ I: 46 W power consumption, 22 l/min maximum flow, 3 m maximum head.
• ລະດັບ II: 63 W power consumption, 38 l/min maximum flow, 5 m maximum head.
• ລະດັບ III: 93 W power consumption, 55 l/min maximum flow, 6 m maximum head.

Adjust the speed setting based on the heating system's requirements to achieve optimal circulation and energy efficiency.

5. ບໍາລຸງຮັກສາ

Regular maintenance ensures the longevity and efficient operation of your circulation pump.

5.1 ການກວດສອບປົກກະຕິ

• ການກວດກາສາຍຕາ: ກວດສອບປໍ້າເປັນໄລຍະໆ ເພື່ອເບິ່ງວ່າມີຮ່ອງຮອຍຂອງການຮົ່ວໄຫຼ, ການກັດກ່ອນ, ຫຼື ຄວາມເສຍຫາຍຕໍ່ລະບົບສູບນ້ຳຫຼືບໍ່.asing ຫຼື ການເຊື່ອມຕໍ່ໄຟຟ້າ.
• ລະດັບສຽງລົບກວນ: Listen for any unusual noises during operation, which could indicate air in the system or a mechanical issue.
• ອຸນຫະພູມ: Ensure the pump is not overheating.

5.2 ການທໍາຄວາມສະອາດ

ຮັກສາພາຍນອກຂອງປັ໊ມສະອາດແລະບໍ່ມີຝຸ່ນແລະສິ່ງເສດເຫຼືອເພື່ອຮັບປະກັນການກະຈາຍຄວາມຮ້ອນທີ່ເຫມາະສົມ.

5.3 ລະດູໜາວ (ຖ້າມີ)

If the heating system is to be shut down for an extended period in freezing temperatures, ensure the system, including the pump, is drained to prevent frost damage.

6. ການແກ້ໄຂບັນຫາ

ພາກນີ້ໃຫ້ຄໍາແນະນໍາສໍາລັບບັນຫາທົ່ວໄປ. ສໍາລັບບັນຫາທີ່ສັບສົນ, ໃຫ້ປຶກສາກັບຊ່າງເຕັກນິກທີ່ມີຄຸນວຸດທິ.

7. ຂໍ້ກໍານົດດ້ານວິຊາການ

8. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

Information regarding the product warranty is not provided in the available data. For warranty claims, technical support, or spare parts inquiries, please contact the original seller or the manufacturer, 4U-Onlinehandel, directly. Keep your purchase receipt as proof of purchase.