LAUNCH Scan Tool CRP123 OBDII Cable Instruction Manual

1. ບົດແນະນຳ

This manual provides instructions for the LAUNCH CRP123 OBDII Main Cable. This cable is designed to connect compatible LAUNCH diagnostic scan tools, such as the CRP123, CRP129, Creader VII+, and Creader VIII, to a vehicle's On-Board Diagnostics II (OBDII) port for diagnostic purposes.

The cable facilitates communication between the scan tool and the vehicle's Electronic Control Unit (ECU), enabling the retrieval of diagnostic trouble codes (DTCs), live data streams, and other vehicle information.

2. ຕັ້ງຄ່າ

2.1 ເນື້ອໃນຊຸດ

• 1 x LAUNCH CRP123 OBDII Main Cable

2.2 ການເຊື່ອມຕໍ່ສາຍ

1. ຊອກຫາພອດ OBDII: ໂດຍປົກກະຕິແລ້ວ ພອດ OBDII ຈະຕັ້ງຢູ່ໃຕ້ແຜງໜ້າປັດດ້ານຂ້າງຂອງຄົນຂັບຂອງລົດ. ໃຫ້ອ້າງອີງໃສ່ຄູ່ມືເຈົ້າຂອງລົດຂອງທ່ານສຳລັບຕຳແໜ່ງທີ່ແນ່ນອນ.
2. Connect to Scan Tool: Plug the 15-pin connector end of the LAUNCH CRP123 OBDII Main Cable into the corresponding port on your LAUNCH CRP123, CRP129, Creader VII+, or Creader VIII scan tool. Ensure a secure connection.
3. ເຊື່ອມຕໍ່ກັບຍານພາຫະນະ: Plug the OBDII connector end of the cable into the vehicle's OBDII port. Ensure the connection is firm.
4. ເປີດ: Once both ends of the cable are securely connected, power on your LAUNCH scan tool. The tool should automatically establish communication with the vehicle's ECU.

Image 1: The LAUNCH CRP123 OBDII Main Cable, showing its coiled black cable and the 15-pin connector designed to interface with compatible LAUNCH scan tools.

3. ການດໍາເນີນງານ

The LAUNCH CRP123 OBDII Main Cable acts as a conduit for data transfer between your vehicle and the diagnostic scan tool. Its operation is passive; the cable itself does not perform diagnostic functions but enables the scan tool to do so.

3.1 Using with Your Scan Tool

1. ໄຟໄໝ້ລົດ: Ensure the vehicle's ignition is in the "ON" position (engine can be off or running, depending on the diagnostic procedure).
2. Scan Tool Interface: Follow the on-screen prompts and instructions provided by your specific LAUNCH scan tool (CRP123, CRP129, Creader VII+, or Creader VIII) to perform diagnostic tasks.
3. ດຶງຂໍ້ມູນ: The cable will transmit data such as Diagnostic Trouble Codes (DTCs), live sensor data, freeze frame data, and vehicle information to your scan tool for analysis.
4. ກຳລັງຕັດການເຊື່ອມຕໍ່: After completing diagnostic procedures, power off the scan tool, then carefully disconnect the cable from the vehicle's OBDII port and the scan tool.

4. ບໍາລຸງຮັກສາ

Proper care and maintenance will extend the lifespan of your LAUNCH CRP123 OBDII Main Cable.

• ທໍາຄວາມສະອາດ: Wipe the cable and connectors with a soft, dry cloth. Avoid using harsh chemicals or abrasive cleaners.
• ການເກັບຮັກສາ: Store the cable in a cool, dry place, away from direct sunlight and extreme temperatures. Coil the cable loosely to prevent kinks or damage to the internal wires.
• ການຈັດການ: Always grasp the connector housing when plugging or unplugging the cable. Avoid pulling directly on the cable itself, as this can damage the internal wiring or strain relief.
• ການກວດກາ: Periodically inspect the cable and connectors for any signs of wear, cuts, bends, or corrosion. If damage is observed, replace the cable to ensure reliable operation and prevent potential issues with your scan tool or vehicle.

5. ການແກ້ໄຂບັນຫາ

If you encounter issues while using the LAUNCH CRP123 OBDII Main Cable, consider the following troubleshooting steps:

• ບໍ່ມີການສື່ສານກັບຍານພາຫະນະ:
  • Ensure both ends of the cable are securely connected to the scan tool and the vehicle's OBDII port.
  • Verify the vehicle's ignition is in the "ON" position.
  • Check the cable for visible damage (cuts, kinks, bent pins). A damaged cable may prevent communication.
  • Confirm the scan tool is powered on and functioning correctly.
  • Test the cable on a different compatible vehicle or with another known-good scan tool, if available, to isolate the issue.
• ການເຊື່ອມຕໍ່ແບບບໍ່ຢຸດຢັ້ງ:
  • Ensure connectors are clean and free of debris or corrosion.
  • Avoid excessive movement or strain on the cable during use.
  • Check for loose internal wiring by gently flexing the cable near the connectors. If the connection drops, the cable may be faulty.
• Scan Tool Error Messages:
  • Refer to your specific LAUNCH scan tool's manual for error code definitions and troubleshooting steps related to communication issues.

If troubleshooting steps do not resolve the issue, the cable may need replacement. Contact LAUNCH customer support for further assistance.

6. ຂໍ້ມູນຈໍາເພາະ

7. ຂໍ້ມູນການຮັບປະກັນ

The LAUNCH CRP123 OBDII Main Cable comes with a ການຮັບປະກັນຫນຶ່ງປີ ນັບຈາກວັນທີ່ຊື້. ການຮັບປະກັນນີ້ກວມເອົາຂໍ້ບົກຜ່ອງຈາກການຜະລິດ ແລະ ຮັບປະກັນວ່າຜະລິດຕະພັນບໍ່ມີຂໍ້ບົກຜ່ອງດ້ານວັດສະດຸ ແລະ ຝີມືການຜະລິດພາຍໃຕ້ການນໍາໃຊ້ປົກກະຕິ.

The warranty does not cover damage caused by misuse, accident, unauthorized modification, or improper installation. For warranty claims or further details, please contact LAUNCH customer support.

8. ການຊ່ວຍເຫຼືອລູກຄ້າ

For technical assistance, troubleshooting, or warranty inquiries regarding your LAUNCH CRP123 OBDII Main Cable, please contact LAUNCH customer support.

Visit the official LAUNCH webເວັບໄຊທ໌ສໍາລັບຂໍ້ມູນຕິດຕໍ່ແລະຊັບພະຍາກອນເພີ່ມເຕີມ: LAUNCH Official Store