LAUNCH CNC602A Injector Cleaner and Tester User Manual

1. ບົດແນະນຳ

The LAUNCH CNC602A Injector Cleaner and Tester is a professional automotive tool designed for comprehensive maintenance of fuel injectors. It performs simultaneous cleaning and testing of multiple injectors, ensuring optimal engine performance and fuel efficiency. This manual provides detailed instructions for safe and effective operation of the device.

2. ຂໍ້ມູນຄວາມປອດໄພ

• Always operate the unit in a well-ventilated area.
• Do not smoke or use open flames near the cleaning or testing fluids.
• ໃສ່ອຸປະກອນປ້ອງກັນສ່ວນບຸກຄົນທີ່ເຫມາະສົມ, ລວມທັງແວ່ນຕາຄວາມປອດໄພແລະຖົງມື.
• Ensure the unit is properly grounded before operation.
• Use only recommended cleaning and testing fluids.
• Do not place anything on the control panel that could interfere with operation or cause damage.
• In case of a damaged power supply or short circuit, discontinue use immediately.

3. ອົງປະກອບຜະລິດຕະພັນ ແລະ ເນື້ອໃນຊຸດ

The LAUNCH CNC602A comes with a comprehensive set of accessories to facilitate various cleaning and testing procedures.

ຮູບພາບ: Various accessories and cables included with the LAUNCH CNC602A Injector Cleaner and Tester.

ລາຍການແພັກເກດ:

• 105020217 CNC pulse signal connection cable 1, T=0.5
• 105020218 CNC pulse signal connection cable 2, T=0.8
• 103260037 Ultrasonic cleaner assembly 100W
• 106030038 On-vehicle adaptor package (tool kits)
• 107010428 CNC-602A user manual (En&Ch)
• 103250013 Top-supply connector 1
• 103250015 Swiss thread adaptor for fuel top-supply injector
• 103250016 Coarse thread adaptor for fuel top-supply injector
• 103250018 CNC-601/801 Hexangular stopper
• 104990012 CNC-801 BUICK injector adaptor
• 199010019 Injector testing liquid (pick out)
• 307030024 Injector detergent (pick out)

4. ຕັ້ງຄ່າ

Before operating the unit, ensure it is placed on a stable, level surface and connected to a suitable power supply (AC110V±10%, 50/60Hz).

ຮູບພາບ: Power switch and socket for connecting the unit to a 110V AC power supply.

ຂັ້ນຕອນເບື້ອງຕົ້ນ:

1. ເຊື່ອມຕໍ່ພະລັງງານ: Plug the unit into a grounded AC110V power outlet.
2. ຕິດຕັ້ງວາວລະບາຍນ້ຳ: Attach the cleaning/testing agent discharge valve to the designated port.
3. Prepare Ultrasonic Bath: Place the ultrasonic cleaning assembly into its designated slot.
4. Install Signal Wires: Connect the pulse signal connection cables to the unit.

5. ຄໍາແນະນໍາການດໍາເນີນງານ

The CNC602A offers both ultrasonic cleaning and various testing functions for fuel injectors.

ຮູບພາບ: The control panel with function selection, pulse width adjustment, and pressure controls.

5.1. Ultrasonic Cleaning Procedure

1. Pre-clean Injectors: Clean the injector's exterior with gasoline or a suitable cleaning liquid before placing them in the unit.
2. Place Injectors: Position the injectors in the ultrasonic bathtub.
3. Add Cleaning Fluid: Pour cleaning fluid into the ultrasonic bathtub, ensuring injectors are submerged.
4. Connect Pulse Signals: Attach the pulse signal cables to the injectors.
5. Activate Ultrasonic System: Turn on the ultrasonic system. The pulsed energy, combined with the cleaning fluid, will dislodge carbon and impurities from inside the injectors.
6. Heat Mode (Optional): If desired, activate the heating mode for enhanced cleaning.

ຮູບພາບ: Injectors undergoing ultrasonic cleaning in the dedicated bath.

5.2. Fuel Injector Testing Procedure

1. Mount Injectors: Secure the cleaned injectors onto the main machine's test bench.
2. Add Test Fluid: Pour the dedicated testing fluid into the fuel tank (4700ml capacity). Ensure the fluid level is within the specified range.
3. Connect Power and Signal: Ensure all injectors are correctly connected for power and pulse signals.
4. Select Test Function: Use the control panel to select the desired test function (e.g., Idle Speed Test, Leakage Test, Sprayability Test).
5. ປັບຕົວກໍານົດການ: Set simulated RPM, time, and pulse width as required for the selected test.
6. ເລີ່ມການທົດສອບ: Initiate the test and observe injector performance in the graduated cylinders.
7. ປັບ​ຄວາມ​ກົດ​ດັນ​: Use the pressure adjustment knob to modify system pressure during testing as needed.

Available Testing Functions:

• ທໍາ​ຄວາມ​ສະ​ອາດ Ultrasonic​: Removes carbon deposits and impurities using ultrasonic vibration.
• Idle Speed Test (0-20ms): Simulates engine idling speed to test injector state.
• Medium Speed Test (0-7.5ms): Simulates medium engine speed to test injector state.
• High-Speed Test (0-4ms): Simulates high engine speed to test injector state.
• ການທົດສອບເລັ່ງ: Simulates vehicle acceleration to test injector performance.
• Shift Speed Test: Simulates vehicle shifting state to test injector working performance.
• ການທົດສອບການຮົ່ວໄຫລ: Checks the sealing condition of the fuel injector.
• Idle Speed Sprayability Test: Tests spray performance at engine idling state.
• Medium Speed Sprayability Test: Tests spray performance at medium engine speed.
• High-Speed Sprayability Test: Tests spray performance at high engine speed.
• Reverse Flush: Cleans injectors by flowing test liquid from outlet to inlet, removing internal dirt or strainers (for top fuel supply injectors).
• No-Disassembly Cleaning: Direct cleaning without disassembling injectors (requires special adapters).

6. ບໍາລຸງຮັກສາ

Regular maintenance ensures the longevity and accuracy of your LAUNCH CNC602A unit.

1. ການຄຸ້ມຄອງຂອງແຫຼວ: After each use, drain all cleaning and testing fluids from the unit. Store fluids properly according to their safety data sheets.
2. ໜ່ວຍງານທີ່ສະອາດ: ເຊັດດ້ານນອກຂອງເຄື່ອງໃຫ້ອ່ອນໆ, ງamp cloth. Avoid using harsh chemicals that may damage the surface or internal components.
3. ກວດກາອົງປະກອບ: Regularly check all hoses, connections, and adapters for wear, damage, or leaks. Replace any damaged parts immediately.
4. ການເກັບຮັກສາ: Store the unit in a clean, dry environment away from direct sunlight and extreme temperatures.

ຮູບພາບ: Fuel intake port and warning label, emphasizing proper fluid handling.

7. ການແກ້ໄຂບັນຫາ

ພາກສ່ວນນີ້ແກ້ໄຂບັນຫາທົ່ວໄປທີ່ທ່ານອາດຈະພົບໃນລະຫວ່າງການປະຕິບັດງານ.

• ຫນ່ວຍບໍລິການບໍ່ເປີດ: Check power cable connection and ensure the power switch is in the 'ON' position. Verify the power outlet is functional.
• No ultrasonic cleaning action: Ensure the ultrasonic cleaning function is selected and the cleaning fluid level is adequate. Check connections to injectors.
• Inconsistent spray pattern/flow: Verify that injectors are clean and free of blockages. Check for proper seating of injectors and adapters. Ensure correct pressure settings.
• ການຮົ່ວໄຫຼຂອງນ້ໍາ: Inspect all connections, hoses, and O-rings for proper sealing. Tighten any loose fittings.
• Pressure gauge not responding: Check the oil supply hose connection and ensure the pressure adjustment knob is functioning correctly.

8. ຂໍ້ມູນຈໍາເພາະ

9. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

The LAUNCH CNC602A Injector Cleaner and Tester comes with a ຮັບປະກັນ 1 ປີ for damages caused by non-human factors. For any needs or support, please contact customer service. We aim to respond within 24 hours.