ຄູ່ມືຜູ້ໃຊ້ປໍ້າກອງ Steinbach SPS 100-1T ແບບ Self-Submitting

1. ຜະລິດຕະພັນເກີນview

The Steinbach SPS 100-1T self-priming filter pump is designed to be the central component of your pool's circulation system. This robust pump features a pre-filter and an integrated timer, making it suitable for pools up to approximately 40,000 liters (10,567 gallons) in volume. It operates on 230V/550W power and offers a pumping capacity of 9,480 liters per hour (158 l/min) with a maximum pump height of 10 meters.

The pump is designed for durability and efficiency, ensuring clean and clear pool water. It is compatible with hose connections of Ø 32/38 mm and can operate with water temperatures up to 35 °C.

ຮູບ 1: ເກີນview of the Steinbach SPS 100-1T Self-Priming Filter Pump. This image shows the complete pump unit, including the motor, pump housing, and pre-filter basket.

2. ຄໍາແນະນໍາຄວາມປອດໄພ

• ສະເຫມີຖອດປັ໊ມຈາກການສະຫນອງພະລັງງານກ່ອນທີ່ຈະດໍາເນີນການບໍາລຸງຮັກສາຫຼືເຮັດຄວາມສະອາດໃດໆ.
• ໃຫ້ແນ່ໃຈວ່າປັ໊ມຖືກຕິດຕັ້ງຢູ່ເທິງໜ້າດິນທີ່ໝັ້ນຄົງ ແລະ ລະດັບເພື່ອປ້ອງກັນການສັ່ນສະເທືອນ ແລະ ການເຄື່ອນໄຫວ.
• Do not operate the pump dry. Ensure it is always filled with water before starting.
• ຮັກສາເດັກນ້ອຍ ແລະສັດລ້ຽງຢູ່ຫ່າງຈາກປໍ້າໃນລະຫວ່າງການປະຕິບັດງານ.
• Only use the pump for its intended purpose (pool water filtration).
• Regularly inspect the power cable for damage. Do not use if damaged.
• Ensure all electrical connections are properly sealed and protected from water.

3. ການຕິດຕັ້ງແລະການຕິດຕັ້ງ

3.1 ການຫຸ້ມຫໍ່

ເອົາສ່ວນປະກອບທັງໝົດອອກຈາກການຫຸ້ມຫໍ່ຢ່າງລະມັດລະວັງ. ກວດສອບວ່າທຸກຊິ້ນສ່ວນມີຢູ່ ແລະ ບໍ່ເສຍຫາຍ. ອ້າງອີງເຖິງລາຍການການຫຸ້ມຫໍ່ສຳລັບສິນຄ້າຄົງຄັງທີ່ຄົບຖ້ວນ.

3.2 ການຈັດວາງ

Position the pump on a firm, level surface, preferably below the water level of the pool for optimal self-priming. Ensure adequate ventilation around the pump to prevent overheating. The pump should be placed in a location protected from direct sunlight and adverse weather conditions.

3.3 ທໍ່ເຊື່ອມຕໍ່

Connect the pool's suction line to the inlet of the pump (the side with the pre-filter) and the return line to the outlet. The pump is designed for Ø 32/38 mm hose connections. Secure all hose connections with appropriate clamps ເພື່ອປ້ອງກັນການຮົ່ວໄຫຼ.

ຮູບທີ 2: ໄລຍະໃກ້ view of the pre-filter inlet with a hose connected. This shows the transparent pre-filter housing and the connection point for the pool's suction hose.

ຮູບທີ 3: ໄລຍະໃກ້ view of the pump outlet with a hose connected. This illustrates the connection point for the pool's return hose.

3.4 Priming the Pump

Before first use, or after the pump has been drained, it must be primed. Open the pre-filter lid and fill the pre-filter basket and pump housing completely with water. Replace the lid securely. This ensures the pump does not run dry, which can cause damage.

ຮູບທີ 4: View of the pre-filter inlet without a hose attached. This shows the threaded connection for the pre-filter housing.

ຮູບທີ 5: View of the pump outlet without a hose attached. This shows the threaded connection for the outlet hose.

3.5 ການເຊື່ອມຕໍ່ໄຟຟ້າ

Connect the pump to a grounded 230V power outlet. Ensure the electrical circuit is protected by a Residual Current Device (RCD) for safety. Do not use extension cords unless absolutely necessary, and ensure they are rated for outdoor use and the pump's power requirements.

4. ຄໍາແນະນໍາການດໍາເນີນງານ

4.1 Starting and Stopping the Pump

Once the pump is primed and all connections are secure, press the ເປີດ/ປິດ button on the control panel to start the pump. Press it again to stop the pump.

4.2 Using the Integrated Timer

The SPS 100-1T pump features an integrated timer for automated operation. Use the ເວລາ button to set the desired operating duration. The control panel typically has indicators for various time settings (e.g., 2, 4, 6, 8, 10, 12, 14, 16, 24 hours). Select the appropriate duration based on your pool's size and usage to ensure adequate filtration.

ຮູບທີ 6: ໄລຍະໃກ້ view of the pump's control panel. This image highlights the ON/OFF and TIMER buttons, along with the indicators for setting the filtration duration.

4.3 Optimal Filtration Time

For optimal water quality, it is generally recommended to filter the entire volume of your pool water at least once per day. The required filtration time depends on the pump's flow rate and your pool's volume. For this pump with a flow rate of 9,480 l/h, a 40,000-liter pool would require approximately 4.2 hours of filtration per day (40,000 L / 9,480 L/h ≈ 4.2 h).

5. ບໍາລຸງຮັກສາ

5.1 Cleaning the Pre-Filter Basket

The pre-filter basket collects larger debris and should be cleaned regularly to maintain pump efficiency.

1. Turn off the pump and disconnect it from the power supply.
2. ໝຸນຝາປິດໂປ່ງໃສຂອງຕົວກອງກ່ອນອອກ.
3. Remove the pre-filter basket and empty any collected debris.
4. Rinse the basket thoroughly with clean water.
5. ກວດສອບປະທັບຕາວົງແຫວນ O-ring ເທິງຝາປິດເພື່ອເບິ່ງຄວາມເສຍຫາຍ ແລະ ຮັບປະກັນວ່າມັນສະອາດ.
6. Place the clean basket back into the housing and securely screw on the lid.
7. ຖ້າຈຳເປັນ, ໃຫ້ສູບນ້ຳຄືນໃໝ່ກ່ອນທີ່ຈະເລີ່ມເຮັດວຽກໃໝ່.

5.2 ລະດູໜາວ

Before the first frost, the pump must be drained and stored in a frost-free environment.

• ຖອດປັ໊ມຈາກການສະຫນອງພະລັງງານ.
• ຕັດການເຊື່ອມຕໍ່ທໍ່ທັງໝົດ.
• Remove the drain plug (if present) or tilt the pump to ensure all water drains out.
• ເຮັດຄວາມສະອາດພາຍນອກຂອງປັ໊ມ.
• ເກັບຮັກສາປໍ້າໄວ້ໃນສະຖານທີ່ແຫ້ງ ແລະ ບໍ່ມີອາກາດໜາວ.

6. ການແກ້ໄຂບັນຫາ

7. ຂໍ້ກໍານົດດ້ານວິຊາການ

8. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

This product comes with a standard manufacturer's warranty. Please refer to your purchase documentation for specific warranty terms and conditions. For technical support, spare parts, or warranty claims, please contact Steinbach customer service or your authorized dealer.

Steinbach Contact Information:

• Webເວັບໄຊ: www.steinbach.at
• ຕົວແບບອ້າງອີງ: 9008748409179

ກະລຸນາມີໝາຍເລກຕົວແບບຂອງທ່ານ (040917) ແລະວັນທີຊື້ພ້ອມເມື່ອຕິດຕໍ່ກັບຝ່າຍຊ່ວຍເຫຼືອ.