Frigidaire 137108000 Drain Pump Instruction Manual

1. ບົດແນະນຳ

This manual provides essential information for the proper installation, operation, and maintenance of your Frigidaire 137108000 Drain Pump. This genuine replacement part is designed for use in washing machines to effectively remove water during the drain cycle. Please read these instructions carefully before proceeding with installation or any service to ensure safe and correct usage.

2. ຂໍ້ມູນຄວາມປອດໄພ

ຄຳເຕືອນ: To reduce the risk of electric shock, fire, or injury to persons, read all instructions before installing or servicing this appliance part.

• Always disconnect the appliance from the power supply before attempting any installation, repair, or maintenance.
• ໃສ່ອຸປະກອນປ້ອງກັນສ່ວນບຸກຄົນທີ່ເຫມາະສົມ, ເຊັ່ນ: ຖົງມືແລະແວ່ນຕາຄວາມປອດໄພ.
• Ensure all water lines are shut off and any residual water is drained before beginning work.
• ຖ້າທ່ານບໍ່ແນ່ໃຈກ່ຽວກັບພາກສ່ວນໃດນຶ່ງຂອງຂະບວນການຕິດຕັ້ງ, ໃຫ້ປຶກສາກັບນັກວິຊາການທີ່ມີຄຸນວຸດທິ.
• ໃຫ້ເດັກນ້ອຍ ແລະສັດລ້ຽງຢູ່ຫ່າງຈາກບ່ອນເຮັດວຽກ.

3. ຜະລິດຕະພັນເກີນview

The Frigidaire 137108000 Drain Pump is a critical component for your washing machine's drainage system. It is responsible for pumping water out of the wash tub during the drain and spin cycles.

ຮູບທີ 1: ດ້ານໜ້າ view of the Frigidaire 137108000 Drain Pump. This image shows the main body and the inlet/outlet ports of the pump.

ຮູບທີ 2: ຂ້າງ view of the Frigidaire 137108000 Drain Pump. This view highlights the motor housing and electrical connections.

4. ການຕິດຕັ້ງ

This section outlines the general steps for replacing a washing machine drain pump. Specific steps may vary depending on your washing machine model. Refer to your appliance's service manual for detailed instructions.

ເຄື່ອງມືທີ່ຕ້ອງການ:

• ທໍ່ລັອກຊ່ອງ
• Stubby screwdriver or small socket wrench set
• Bucket or shallow pan for draining water
• ຜ້າເຊັດຕົວ
• New screw-type hose clamps (recommended over spring clamps for easier installation and better seal)

ຂັ້ນ​ຕອນ​ການ​ຕິດ​ຕັ້ງ​:

1. ຕັດການເຊື່ອມຕໍ່ພະລັງງານ: ຖອດປລັກເຄື່ອງຊັກຜ້າອອກຈາກປ່ຽງໄຟຟ້າ.
2. ປິດການສະຫນອງນ້ໍາ: Turn off the hot and cold water supply valves to the washer.
3. ລະບາຍນ້ຳທີ່ຕົກຄ້າງ: Place a bucket or shallow pan under the drain hose and lower the hose to drain any remaining water from the tub.
4. ເຂົ້າເຖິງປັ໊ມ: Depending on your washer model, you may need to remove the front panel, rear panel, or tilt the machine back to access the drain pump.
5. ຕັດການເຊື່ອມຕໍ່ທໍ່: Use channel lock pliers to loosen and remove the hose clamps securing the inlet and outlet hoses to the old drain pump. Be prepared for some water spillage.
6. ຕັດການເຊື່ອມຕໍ່ສາຍໄຟ: Carefully disconnect the electrical wiring harness from the old pump. Note the orientation if necessary.
7. ເອົາປ້ຳເກົ່າອອກ: Unscrew any mounting screws or release clips holding the old pump in place and remove it.
8. ຕິດຕັ້ງປັ໊ມໃໝ່: Position the new Frigidaire 137108000 Drain Pump in the same location and secure it with the mounting screws or clips.
9. ເຊື່ອມຕໍ່ສາຍທໍ່ຄືນໃໝ່: Attach the inlet and outlet hoses to the new pump. Secure them tightly with new screw-type hose clamps ເພື່ອປ້ອງກັນການຮົ່ວໄຫຼ.
10. ເຊື່ອມຕໍ່ສາຍໄຟຄືນໃໝ່: Connect the electrical wiring harness to the new pump.
11. ປະກອບເຄື່ອງຊັກຜ້າຄືນໃໝ່: Reattach any panels removed during access.
12. ການ​ປະ​ຕິ​ບັດ​ການ​ທົດ​ສອບ​: Turn on the water supply, plug in the washing machine, and run a short drain or rinse cycle to check for proper function and leaks.

5. ການດໍາເນີນງານ

The Frigidaire 137108000 Drain Pump operates automatically as part of your washing machine's cycle. When the washer enters a drain or spin phase, the control board activates the pump to remove water from the wash tub. No manual intervention is required for its normal operation.

6. ບໍາລຸງຮັກສາ

ການບຳລຸງຮັກສາເປັນປະຈຳສາມາດຍືດອາຍຸການໃຊ້ງານຂອງປ້ຳລະບາຍນ້ຳຂອງທ່ານ ແລະ ປ້ອງກັນບັນຫາທົ່ວໄປໄດ້.

• ກວດ​ສອບ​ສໍາ​ລັບ Debris​: Periodically inspect the drain pump filter (if accessible on your washer model) and the pump's impeller for lint, coins, socks, or other foreign objects that can obstruct flow or damage the pump.
• Clean Drain Hose: If drainage issues occur, consider purging or cleaning the drain hose to remove any blockages.
• ກວດ​ສອບ​ທໍ່: Check the inlet and outlet hoses connected to the pump for cracks, kinks, or loose connections that could lead to leaks.

7. ການແກ້ໄຂບັນຫາ

If you experience problems with your washing machine's drainage, the following troubleshooting steps may help.

ບັນຫາທົ່ວໄປ ແລະການແກ້ໄຂ:

• Washer Not Draining:
  • Ensure the drain hose is not kinked or clogged.
  • Check the pump filter for obstructions.
  • Verify that the pump is receiving electrical power.
  • The pump impeller may be damaged or seized.
• ການດໍາເນີນງານທີ່ມີສຽງດັງ:
  • A new pump may operate with a slightly different sound than an old, failing pump. This is often normal.
  • Excessive noise could indicate debris caught in the impeller or a worn motor bearing. Disconnect power and inspect.
• Leaks Around Pump:
  • Check all hose connections to ensure they are tight and properly sealed, especially if new screw-type hose clamps were not used or tightened sufficiently.
  • Inspect the pump housing for cracks or damage.

If these steps do not resolve the issue, it may be necessary to consult a qualified appliance repair technician.

8. ຂໍ້ມູນຈໍາເພາະ

9. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

This Frigidaire genuine replacement part is covered by the manufacturer's standard warranty. For specific warranty details, claims, or technical support, please refer to the documentation provided with your original appliance or visit the official Frigidaire webເວັບໄຊ. ຮັກສາໃບຮັບເງິນການຊື້ຂອງທ່ານໄວ້ເປັນຫຼັກຖານການຊື້ເພື່ອຈຸດປະສົງການຮັບປະກັນ.

For further assistance, you may contact Frigidaire customer service through their official channels.