PerTronix Flame-Thrower Electronic Ignition Distributor User Manual

1. ບົດແນະນຳ

This manual provides comprehensive instructions for the installation, operation, maintenance, and troubleshooting of your PerTronix Flame-Thrower Electronic Ignition Distributor (Model D134600). This distributor is designed to provide enhanced ignition performance for compatible Ford Small Block engines, featuring integrated Ignitor electronic ignition technology for improved reliability and power.

ກະລຸນາອ່ານຄູ່ມືນີ້ຢ່າງລະອຽດກ່ອນການຕິດຕັ້ງ ແລະ ການດຳເນີນງານເພື່ອຮັບປະກັນການເຮັດວຽກ ແລະ ຄວາມປອດໄພທີ່ເໝາະສົມ.

2. ຂໍ້ມູນຄວາມປອດໄພ

ປະຕິບັດຕາມຄວາມລະມັດລະວັງດ້ານຄວາມປອດໄພຕໍ່ໄປນີ້ສະເໝີ:

• ຖອດແບັດເຕີຣີຂອງລົດອອກກ່ອນທີ່ຈະເຮັດວຽກໄຟຟ້າໃດໆ.
• ໃສ່ອຸປະກອນປ້ອງກັນສ່ວນບຸກຄົນທີ່ເຫມາະສົມ (PPE), ລວມທັງແວ່ນຕາຄວາມປອດໄພແລະຖົງມື.
• Ensure the engine is cool before working on ignition components.
• Keep ignition components away from flammable materials.
• Consult a qualified mechanic if you are unsure about any installation steps.
• ຜະລິດຕະພັນນີ້ປະກອບດ້ວຍສານເຄມີທີ່ຮູ້ກັນໃນລັດຄາລິຟໍເນຍເພື່ອເຮັດໃຫ້ເກີດມະເຮັງແລະຄວາມຜິດປົກກະຕິໃນການເກີດລູກຫຼືເປັນອັນຕະລາຍຕໍ່ການຈະເລີນພັນອື່ນໆ. ລ້າງມືຫຼັງຈາກຈັບ.

3. ສິ່ງທີ່ຢູ່ໃນກ່ອງ

ກວດ​ສອບ​ວ່າ​ອົງ​ປະ​ກອບ​ທັງ​ຫມົດ​ແມ່ນ​ມີ​ຢູ່​ກ່ອນ​ທີ່​ຈະ​ເລີ່ມ​ຕົ້ນ​ການ​ຕິດ​ຕັ້ງ​:

• PerTronix Flame-Thrower Electronic Ignition Distributor (Model D134600)
• Distributor Cap
• ໂຣເຕີ
• ຄໍາແນະນໍາການຕິດຕັ້ງ (ຄູ່ມືນີ້)

Image: PerTronix Flame-Thrower Electronic Ignition Distributor with cap, rotor, and wiring visible.

4. ການຕິດຕັ້ງແລະການຕິດຕັ້ງ

ການຕິດຕັ້ງທີ່ເຫມາະສົມແມ່ນສໍາຄັນສໍາລັບການປະຕິບັດທີ່ດີທີ່ສຸດ. ປະຕິບັດຕາມຂັ້ນຕອນເຫຼົ່ານີ້ຢ່າງລະມັດລະວັງ:

1. ການກະກຽມ:
   • ຖອດສາຍແບດເຕີລີ່ລົບອອກ.
   • Mark the position of the rotor on the old distributor relative to the distributor body, and the position of the distributor body relative to the engine block. This will help with re-timing.
   • Label all spark plug wires before removal.
2. Old Distributor Removal:
   • Remove the distributor cap and spark plug wires.
   • Disconnect any electrical connections to the old distributor.
   • Loosen the distributor hold-down clamp and carefully lift the old distributor out of the engine block. Note the rotation of the rotor as it comes out.
3. New Distributor Installation:
   • Ensure the engine is at Top Dead Center (TDC) on the compression stroke for cylinder #1.
   • Align the new PerTronix distributor's gear with the camshaft gear. The rotor should point to the #1 spark plug terminal on the cap when fully seated. You may need to slightly rotate the rotor or the oil pump drive shaft to engage the gears.
   • Once seated, ensure the distributor body is oriented correctly as marked during removal.
   • Secure the distributor with the hold-down clamp, but do not fully tighten yet to allow for timing adjustments.
4. ການເຊື່ອມຕໍ່ສາຍໄຟ:
   • The PerTronix Ignitor module has two wires: a red wire and a black wire.
   • ເຊື່ອມ​ຕໍ່ ສາຍສີແດງ to a switched 12-volt power source that is active when the ignition is in the "ON" and "START" positions. This must be a full 12V source, not a resisted wire.
   • ເຊື່ອມ​ຕໍ່ ສາຍສີດໍາ to the negative (-) terminal of the ignition coil.
   • Ensure all connections are clean and secure.
5. Final Assembly and Timing:
   • Install the new distributor cap and reattach the spark plug wires in the correct firing order.
   • ເຊື່ອມຕໍ່ສາຍສາກລົບຄືນໃໝ່.
   • Start the engine and use a timing light to set the ignition timing according to your vehicle's specifications.
   • Once timing is set, fully tighten the distributor hold-down clamp.

ຮູບພາບ: Examples of Flame-Thrower distributors, illustrating the "Stock Look" and "Billet Plug n' Play" designs. The D134600 is a "Stock Look" model.

5. ຄໍາແນະນໍາການດໍາເນີນງານ

The PerTronix Flame-Thrower Electronic Ignition Distributor operates automatically once installed and timed correctly. It replaces traditional points and condenser systems with a maintenance-free electronic module.

• The integrated Ignitor system delivers a consistent, high-energy spark to the spark plugs, improving combustion efficiency.
• The precision timing control ensures stable engine performance across all RPM ranges.
• No adjustments are required for the electronic ignition system itself after initial timing.

6. ບໍາລຸງຮັກສາ

The PerTronix Flame-Thrower Electronic Ignition Distributor is designed for minimal maintenance. Unlike traditional points systems, there are no points to adjust or replace.

• ການກວດກາປົກກະຕິ: Periodically inspect the distributor cap and rotor for cracks, carbon tracking, or excessive wear. Replace if necessary.
• ສາຍໄຟ: Check all electrical connections for tightness and corrosion. Ensure wiring is routed away from hot or moving engine components.
• ທໍາຄວາມສະອາດ: Keep the exterior of the distributor clean and free from oil, grease, and dirt. Use a clean, dry cloth.
• Spark Plugs & Wires: For optimal performance, ensure your spark plugs and spark plug wires are in good condition and are compatible with electronic ignition systems.

7. ການແກ້ໄຂບັນຫາ

If you experience issues with your ignition system, consider the following common problems and solutions:

If problems persist after troubleshooting, contact PerTronix technical support.

8. ຂໍ້ມູນຈໍາເພາະ

9. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

PerTronix products are manufactured to high standards and are backed by a limited warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official PerTronix webເວັບໄຊ.

For technical support, installation assistance, or warranty claims, please contact PerTronix customer service:

• Webເວັບໄຊ: www.pertronix.com
• ໂທລະສັບ: ອ້າງເຖິງ webເວັບໄຊສຳລັບເບີໂທຕິດຕໍ່ປັດຈຸບັນ.
• When contacting support, please have your product model number (D134600) and purchase information ready.