ຄູ່ມືຜູ້ໃຊ້ທໍ່ສູບນ້ຳຕູ້ປາ Eheim 394 (ຮຸ່ນ 8581)

1. ບົດແນະນຳ

This manual provides essential information for the proper use and maintenance of your Eheim 394 Aquarium Water Pump Tubing. Please read these instructions carefully before installation and operation to ensure optimal performance and longevity of the product.

2. ຜະລິດຕະພັນເກີນview

The Eheim 394 Tubing is designed as an accessory for aquarium water pumps, facilitating water circulation within your aquatic system. It is made from durable plastic and supplied in a continuous length, typically 10 feet (117.6 inches), to accommodate various aquarium setups. The tubing features a 3/8-inch inner diameter (ID), making it compatible with a range of Eheim and other standard aquarium pump connections.

Image: A coiled length of Eheim 394 aquarium tubing, appearing green in color, secured with a white zip tie. The tubing is designed for use with aquarium water pumps and is approximately 10 feet long.

3. ຕັ້ງຄ່າ

1. ກວດສອບຄວາມເຂົ້າກັນໄດ້: Verify that the 3/8-inch inner diameter of this tubing is compatible with the inlet and outlet connections of your aquarium water pump and other filtration components.
2. ການ​ວັດ​ແທກ​ແລະ​ການ​ຕັດ​: Determine the required length of tubing for your setup. Use a sharp utility knife or specialized tubing cutter to make clean, straight cuts. Avoid jagged edges, which can impede flow or cause leaks.
3. ເຊື່ອມຕໍ່ກັບປັ໊ມ: Carefully push the tubing onto the appropriate pump nozzles or connectors. Ensure a snug fit to prevent leaks. If the tubing is stiff, briefly warm the end in warm water to make it more pliable.
4. Route Tubing: Position the tubing to avoid kinks, sharp bends, or obstructions that could restrict water flow. Secure the tubing with appropriate clamps or ties if necessary, ensuring they do not compress the tubing.
5. ການທົດສອບຮົ່ວ: Before fully operating your aquarium system, perform a leak test by running water through the connected components. Check all connections for drips or leaks and adjust as needed.

4. ຄໍາແນະນໍາການດໍາເນີນງານ

Once installed, the Eheim 394 Tubing operates passively as a conduit for water flow. Ensure that your water pump is functioning correctly and that water is circulating freely through the tubing without any blockages or air pockets. Regularly observe the tubing for any signs of kinking or collapse, which can reduce pump efficiency and water flow.

5. ບໍາລຸງຮັກສາ

• ການກວດກາປົກກະຕິ: Periodically inspect the tubing for signs of wear, hardening, discoloration, or algae buildup.
• ທໍາຄວາມສະອາດ: If algae or debris accumulates inside the tubing, disconnect it from the system. Use a flexible brush designed for aquarium tubing or flush with warm water to remove buildup. Avoid harsh chemicals or abrasive cleaners.
• ການທົດແທນ: Over time, tubing can become brittle or develop micro-cracks. Replace the tubing if it shows significant signs of degradation to prevent leaks and maintain optimal system performance.

6. ການແກ້ໄຂບັນຫາ

• ການ​ຫຼຸດ​ຜ່ອນ​ການ​ໄຫຼ​ຂອງ​ນ​້​ໍ​າ​: Check for kinks in the tubing, blockages from debris or algae, or improper connections. Ensure the pump is operating correctly.
• ການຮົ່ວໄຫຼໃນການເຊື່ອມຕໍ່: Verify that the tubing is securely seated on the pump nozzles or connectors. If necessary, use hose clamps for a tighter seal. Ensure the tubing ends are cut cleanly.
• Tubing Too Stiff: If the tubing is difficult to connect, briefly immerse the ends in warm water to increase flexibility.

7. ຂໍ້ມູນຈໍາເພາະ

8. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

For warranty information or technical support regarding your Eheim 394 Tubing, please refer to the official Eheim website or contact Eheim customer service directly. Keep your purchase receipt as proof of purchase.

Eheim Official Webເວັບໄຊ: www.eheim.com