ANEX Ultra Low Profile ຄູ່ມືການໃຊ້ງານໄຂຄວງແບບອອບເຊັດ ຮຸ່ນ 436

1. ບົດແນະນຳ

This manual provides instructions for the safe and effective use of your ANEX Ultra Low Profile Offset Ratcheting Screwdriver, Model 436. This tool is designed for accessing and fastening screws in confined or hard-to-reach areas where traditional screwdrivers cannot be used.

2. ຂໍ້ມູນຄວາມປອດໄພ

• ໃສ່ອຸປະກອນປ້ອງກັນຕາທີ່ເໝາະສົມສະເໝີເມື່ອໃຊ້ເຄື່ອງມື.
• Ensure the screwdriver bit is correctly seated and matches the screw head type and size to prevent stripping the screw or damaging the bit.
• Do not use the tool for purposes other than its intended use as a screwdriver.
• Keep hands and fingers clear of moving parts, especially the ratcheting mechanism.
• ເກັບຮັກສາເຄື່ອງມືໄວ້ໃນບ່ອນແຫ້ງ ແລະ ປອດໄພ ຫ່າງຈາກເດັກນ້ອຍ.

3. ຜະລິດຕະພັນເກີນview

The ANEX Model 436 features a low-profile, offset design with a ratcheting mechanism, ideal for tight spaces. It includes a magnetic bit holder for secure bit retention.

ຮູບທີ 3.1: ໂດຍລວມ view of the ANEX Ultra Low Profile Offset Ratcheting Screwdriver with an inserted bit.

ຮູບທີ 3.2: ໄລຍະໃກ້ view of the magnetic bit holder, ensuring bits are securely held during use.

4. ຕັ້ງຄ່າ

The ANEX Model 436 comes with two standard bits: a Phillips (+2 mm) and a Flathead (-6 mm).

1. ເລືອກບິດທີ່ຖືກຕ້ອງ: Choose the appropriate bit (Phillips or Flathead) that matches the screw head you intend to work with.
2. ໃສ່ Bit: Firmly push the selected bit into the magnetic bit holder at the end of the ratcheting head. The magnet will secure the bit in place.

5. ການດໍາເນີນງານ

5.1 Ratcheting Mechanism

The screwdriver features a three-position switch on the ratcheting head:

• Forward (Tighten): Position the switch to allow rotation in the clockwise direction for tightening screws.
• Reverse (Loosen): Position the switch to allow rotation in the counter-clockwise direction for loosening screws.
• ລັອກ: Position the switch to lock the head, allowing the tool to be used as a fixed screwdriver.

5.2 Using in Tight Spaces

The ultra-low profile and 90-degree offset head are specifically designed for areas with limited clearance. Insert the bit into the screw head, ensuring a snug fit. The flat handle allows for easy application of pressure.

Figure 5.1: Demonstrating the screwdriver's ability to access screws in extremely tight and confined areas.

5.3 Applying Pressure

For effective fastening or loosening, apply downward pressure on the flat handle while rotating the tool. The design of the handle facilitates this, even in awkward positions.

Figure 5.2: Illustration of proper hand placement and pressure application for optimal use.

6. ບໍາລຸງຮັກສາ

• ທໍາຄວາມສະອາດ: Wipe the tool clean with a dry cloth after each use to remove dirt, grease, or debris. Do not use harsh chemicals or abrasive cleaners.
• ການເກັບຮັກສາ: Store the screwdriver and bits in a clean, dry environment to prevent rust and damage.
• ການກວດກາ: Periodically inspect the tool for any signs of wear or damage. Discontinue use if any damage is found and replace if necessary.

7. ການແກ້ໄຂບັນຫາ

• ການເລື່ອນບິດ: Ensure the bit is fully inserted into the magnetic holder and that it correctly matches the screw head. Worn bits should be replaced.
• ກົນໄກການໝຸນບໍ່ມີສ່ວນຮ່ວມ: Check the direction switch to ensure it is fully engaged in either the forward or reverse position, not in between.
• Difficulty Turning Screws: Ensure sufficient downward pressure is applied. For extremely tight screws, apply penetrating oil if appropriate for the application.

8. ຂໍ້ມູນຈໍາເພາະ

Figure 8.1: Detailed dimensions of the screwdriver, including length and thickness.

9. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

Specific warranty information for the ANEX Ultra Low Profile Offset Ratcheting Screwdriver Model 436 is not provided in this document. For warranty details, product support, or service inquiries, please contact the manufacturer directly or refer to the product packaging.