ຄູ່ມືຜູ້ໃຊ້ DSC WS4945 ສັນຍານເຕືອນໄພໄຮ້ສາຍສຳລັບປະຕູ/ປ່ອງຢ້ຽມ

ແນະນຳ

This manual provides comprehensive instructions for the installation, operation, and maintenance of the DSC WS4945 Wireless Alarm Door/Window Contact/Transmitter. This device is designed to enhance security by detecting the opening of doors or windows and transmitting a signal to a compatible alarm system.

ຄຸນນະສົມບັດທີ່ສໍາຄັນ

• Built-in reed switch for magnetic contact detection.
• Normally closed external contact input for additional wired sensors.
• Includes one CR2 lithium battery for power.
• Features case and wall tampການກວດຈັບ er ເພື່ອຄວາມປອດໄພທີ່ດີຂຶ້ນ.

ເນື້ອໃນຊຸດ

ກວດ​ສອບ​ວ່າ​ມີ​ລາຍ​ການ​ທັງ​ຫມົດ​ກ່ອນ​ທີ່​ຈະ​ສືບ​ຕໍ່​ການ​ຕິດ​ຕັ້ງ​:

• DSC WS4945 Wireless Door/Window Contact/Transmitter unit
• 1 CR2 ແບດເຕີລີ່ Lithium
• Mounting hardware (screws, adhesive tape)

ການຕິດຕັ້ງແລະການຕິດຕັ້ງ

Proper installation is crucial for optimal performance. Ensure your alarm system is in test mode before beginning installation to avoid false alarms.

1. ການຕິດຕັ້ງຫມໍ້ໄຟ

1. ເປີດ c ດ້ວຍຄວາມລະມັດລະວັງasing of the WS4945 unit.
2. Insert the provided CR2 lithium battery into the battery compartment, observing correct polarity (+/-).
3. ປິດຄasing ຢ່າງປອດໄພ.

2. ການຕິດຕັ້ງເຊັນເຊີ

The WS4945 is designed for wall mount installation on doors or windows. The main unit (transmitter) and the magnet must be mounted in close proximity, typically within 0.5 inches (1.27 cm) when the door/window is closed.

• Identify a suitable location on the door/window frame and the moving part (door/window) where the sensor and magnet can be aligned.
• Use the included screws or adhesive tape to securely attach the main sensor unit to the frame.
• Attach the magnet to the moving part of the door or window, ensuring it aligns with the marked area on the sensor when closed.

Image: The DSC WS4945 Wireless Door/Window Contact Transmitter. This white rectangular unit houses the electronics and battery, designed to be mounted on a door or window frame.

3. External Contact Input (Optional)

The WS4945 includes a normally closed external contact input, allowing for the connection of an additional wired sensor.

1. Locate the external contact terminals inside the WS4945 casing.
2. Connect the wires from your external normally closed sensor to these terminals.
3. Ensure connections are secure before closing the casing.

4. System Enrollment/Programming

To integrate the WS4945 with your alarm system, it must be enrolled or programmed. This process typically requires the installer code for your alarm panel.

• Refer to your alarm system's main control panel manual for specific instructions on enrolling new wireless devices.
• Typically, you will enter the installer programming mode (*8 followed by the installer code).
• Navigate to the zone programming section and follow the prompts to learn the new sensor. This often involves activating the sensor (e.g., opening and closing the door/window) to transmit its unique serial number.
• Assign the sensor to the appropriate zone and configure its attributes (e.g., door/window, delay, chime).
• Exit programming mode and test the sensor's functionality.

ການດໍາເນີນງານ

The DSC WS4945 operates as a contact sensor. When the protected door or window is closed, the magnet is in close proximity to the main sensor unit, indicating a secure state. When the door or window is opened, the magnet moves away from the sensor, breaking the contact. This change in state is detected by the WS4945, which then transmits a signal to your alarm control panel.

• ສະຖານະປິດ: Magnet is adjacent to the sensor.
• ສະຖານະເປີດ: Magnet is separated from the sensor, triggering a signal transmission.
• Tamper ການ​ກວດ​ສອບ​: ຖ້າຄ. ສasing is opened or the unit is removed from its mounting surface, a tamper signal will be sent to the alarm panel.

ບໍາລຸງຮັກສາ

ການປ່ຽນແບັດ

The WS4945 uses one CR2 lithium battery. When the battery voltage drops, your alarm system will typically indicate a low battery condition for the specific zone. Replace the battery promptly to ensure continuous operation.

1. Place your alarm system in test mode to prevent false alarms during battery replacement.
2. ເປີດເຊັນເຊີ casing.
3. ເອົາແບັດ CR2 ເກົ່າອອກ.
4. Insert a new CR2 lithium battery, ensuring correct polarity.
5. ປິດຄasing ຢ່າງປອດໄພ.
6. Test the sensor to confirm it is communicating with the alarm panel.

ທໍາຄວາມສະອາດ

Clean the exterior of the sensor with a soft, dry cloth. Avoid using abrasive cleaners or solvents, as these can damage the casing ຫຼືອົງປະກອບພາຍໃນ.

ການແກ້ໄຂບັນຫາ

• Sensor Not Responding / False Alerts:
  • ກວດເບິ່ງລະດັບຫມໍ້ໄຟແລະປ່ຽນແທນຖ້າຈໍາເປັນ.
  • Ensure the magnet is properly aligned with the sensor and within the recommended gap when the door/window is closed.
  • Verify the sensor is securely mounted and not loose.
  • Confirm the sensor is correctly enrolled in your alarm system. Re-enroll if issues persist.
  • Consider the polling interval setting on your alarm panel; a very short interval might cause intermittent "no response" alerts in some systems.
• Tampການເຕືອນໄພ:
  • Ensure the sensor casing is fully closed and latched.
  • Verify the unit is securely mounted to the wall/frame.
• External Contact Input Not Working:
  • Check wiring connections to the external contact terminals for security and correct polarity.
  • Test the external sensor independently to ensure it is functioning correctly.

ຂໍ້ມູນຈໍາເພາະ

ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

For warranty information and technical support, please refer to the official DSC website or contact your authorized DSC dealer. Keep your purchase receipt as proof of purchase.