1. ບົດແນະນຳ
This manual provides detailed instructions for the proper installation, operation, and maintenance of your Lanzar VIBE211 Vibe 360 Watt 2 Channel Mosfet Ampຕົວຊີ້ບອກ. ກະລຸນາອ່ານຄູ່ມືນີ້ຢ່າງລະອຽດກ່ອນທີ່ຈະພະຍາຍາມຕິດຕັ້ງ ຫຼືດໍາເນີນການ ampເຄື່ອງໃຊ້ໄຟຟ້າເພື່ອຮັບປະກັນປະສິດທິພາບ ແລະ ຄວາມປອດໄພທີ່ດີທີ່ສຸດ.
2. ຂໍ້ມູນຄວາມປອດໄພ
ປະຕິບັດຕາມຄວາມລະມັດລະວັງດ້ານຄວາມປອດໄພຕໍ່ໄປນີ້ສະເໝີໃນລະຫວ່າງການຕິດຕັ້ງ ແລະ ການດໍາເນີນງານ:
- Disconnect the vehicle's negative battery terminal before any wiring connections are made.
- ຮັບປະກັນວ່າສາຍໄຟທັງໝົດໄດ້ຖືກວາງ ແລະ ຮັດແໜ້ນຢ່າງຖືກຕ້ອງເພື່ອປ້ອງກັນຄວາມເສຍຫາຍ ຫຼື ວົງຈອນສັ້ນ.
- ໃຊ້ສາຍໄຟຂະໜາດທີ່ເໝາະສົມສຳລັບການເຊື່ອມຕໍ່ພະລັງງານ ແລະ ສາຍດິນຕາມທີ່ລະບຸໄວ້ໃນພາກສ່ວນການຕິດຕັ້ງ.
- ພູ ampຕິດຕັ້ງເຄື່ອງປັບອາກາດຢ່າງປອດໄພໃນສະຖານທີ່ທີ່ມີລະບາຍອາກາດພຽງພໍ ແລະ ປ້ອງກັນຈາກຄວາມຊຸ່ມຊື່ນ ແລະ ຄວາມຮ້ອນທີ່ເກີນ.
- ຢ່າປະຕິບັດການ amplifier if it is damaged or malfunctioning. Refer to the troubleshooting section or seek professional assistance.
3. ຜະລິດຕະພັນເກີນview
The Lanzar VIBE211 is a 2-channel Mosfet amplifier designed for car audio systems. It features a bridgeable design, allowing for flexible configuration, and incorporates a regulated Mosfet power supply for stable performance. Key features include variable high/low pass crossover controls and a remote subwoofer bass control.
ເປັນມຸມ view of the silver Lanzar VIBE211 Vibe 360 Watt 2 Channel Mosfet Amplifier, showcasing its finned heatsink design, RCA inputs, and control panel. The amplifier features text indicating 'bridgeable 2 channel amplifier', 'vibe 211', 'Lanzar vibe', '360 watts', 'high/low pass crossover', and 'regulated mosfet power supply'. A small, separate remote bass level control unit is visible in the foreground.
4. ການຕິດຕັ້ງແລະການຕິດຕັ້ງ
4.1 ການຕິດຕັ້ງ Ampມີຊີວິດຊີວາ
Choose a secure mounting location that provides adequate air circulation around the amplifier's heatsink. Avoid mounting in direct sunlight or areas prone to moisture. Use the provided mounting hardware to secure the ampຍຶດຕິດຢ່າງແໜ້ນໜາກັບພື້ນຜິວທີ່ແຂງ.
4.2 ການເຊື່ອມຕໍ່ສາຍໄຟ
Ensure all connections are tight and properly insulated to prevent short circuits.
- ພະລັງງານ (B+): Connect a heavy-gauge wire (e.g., 8 AWG or larger) directly from the positive terminal of the vehicle's battery to the amplifier's B+ terminal. Install an appropriate fuse (15A) within 18 inches of the battery.
- ດິນ (GND): Connect a heavy-gauge wire of the same size as the power wire from the amplifier's GND terminal to a clean, unpainted metal surface of the vehicle chassis. Ensure a good electrical connection.
- ຫ່າງໄກສອກຫຼີກ (REM): Connect a smaller gauge wire (e.g., 18 AWG) from the ampສາຍ REM ຂອງເຄື່ອງຂະຫຍາຍສຽງໄປຫາຜົນຜະລິດເປີດເຄື່ອງຈາກໄລຍະໄກຂອງຫົວໜ່ວຍຂອງທ່ານ. ສາຍນີ້ຈະໝຸນ amplifier ເປີດແລະປິດດ້ວຍ stereo ຂອງທ່ານ.
- ການປ້ອນຂໍ້ມູນ RCA: Connect the RCA audio cables from your head unit's pre-amp ຜົນໄດ້ຮັບກັບ amplifier's Gold RCA Inputs. The amplifier includes Line Outs for Left and Right Channels for daisy-chaining to other ampຜູ້ຊ່ວຍຊີວິດ.
- ຜົນອອກຂອງລຳໂພງ: Connect your speakers to the amplifier's speaker terminals. Observe correct polarity (+ to + and - to -). The amplifier is 2 Ohm stereo stable and bridgeable at 4 Ohms.
- Remote Subwoofer Bass Control: Connect the remote bass control unit to the designated port on the amplifier. Mount the control unit in an accessible location for easy adjustment.
5. ຄໍາແນະນໍາການດໍາເນີນງານ
5.1 ການເປີດພະລັງງານເບື້ອງຕົ້ນ
After all connections are made, reconnect the vehicle's negative battery terminal. Turn on your head unit. The amplifier features Soft Turn On/Off circuitry to prevent pops and clicks. Power Protection LED Indicators will illuminate to show operational status.
5.2 Adjusting Input Level Controls
ໄດ້ amplifier has Variable Input Level Controls. Start with the amplifier's input level set to minimum. Play a familiar piece of music through your head unit at about 75% of its maximum volume. Slowly increase the ampລະດັບການປ້ອນຂໍ້ມູນຂອງຕົວເພີ່ມສຽງຈົນກວ່າທ່ານຈະໄດ້ຍິນສຽງບິດເບືອນເລັກນ້ອຍ, ຈາກນັ້ນຫຼຸດມັນລົງເລັກນ້ອຍ. ສິ່ງນີ້ຮັບປະກັນ ampເຄື່ອງຮັບສັນຍານທີ່ດີທີ່ສຸດໂດຍບໍ່ຕ້ອງຕັດ.
5.3 ການຕັ້ງຄ່າ Crossover
ໄດ້ amplifier features Variable High Low Pass Crossover Controls. These allow you to filter specific frequencies to your speakers or subwoofers.
- ການກັ່ນຕອງຜ່ານສູງ (HPF): Used for full-range speakers to prevent low frequencies from reaching them, improving clarity.
- ຕົວກອງຜ່ານຕໍ່າ (LPF): Used for subwoofers to allow only low frequencies to pass, enhancing bass response.
Adjust these controls to match the frequency response characteristics of your speakers and subwoofers.
5.4 Bass Boost Circuit
The built-in Bass Boost Circuit allows for an increase in bass output at specific frequencies. Use this feature sparingly and adjust to your preference, avoiding excessive boosting that could lead to distortion or speaker damage.
5.5 ການດໍາເນີນງານແບບ Bridged Mode
ໄດ້ amplifier can be bridged at 4 Ohms to combine the power of both channels into a single, higher-power output, typically for driving a subwoofer. Refer to the wiring diagram for specific instructions on bridging the ampມີຊີວິດຊີວາ.
6. ບໍາລຸງຮັກສາ
The Lanzar VIBE211 amplifier requires minimal maintenance. Periodically inspect the wiring connections for tightness and corrosion. Keep the amplifier's heatsink clean and free of dust or debris to ensure proper cooling. Use a soft, dry cloth for cleaning the exterior.
7. ການແກ້ໄຂບັນຫາ
ຖ້າເຈົ້າປະສົບບັນຫາກັບເຈົ້າ amplifier, ປຶກສາຫາລືຕາຕະລາງຕໍ່ໄປນີ້ກ່ອນທີ່ຈະຊອກຫາການບໍລິການມືອາຊີບ:
| ບັນຫາ | ສາເຫດທີ່ເປັນໄປໄດ້ | ການແກ້ໄຂ |
|---|---|---|
| ບໍ່ມີພະລັງງານ / ບໍ່ມີສຽງ | Blown fuse; Loose power/ground/remote wire; Faulty head unit. | Check and replace fuse; Verify all power, ground, and remote connections; Test head unit functionality. |
| ສຽງບິດເບືອນ | Input level too high; Speaker impedance too low; Damaged speakers. | Adjust input level; Verify speaker impedance (2 Ohm stereo stable, 4 Ohm bridged); Inspect speakers for damage. |
| Amplifier Goes into Protection Mode | ຮ້ອນເກີນໄປ; ວົງຈອນສັ້ນໃນສາຍໄຟລຳໂພງ; ສຽງຕ່ຳtage. | Ensure adequate ventilation; Check speaker wires for shorts; Verify battery voltage ແລະລະບົບການສາກໄຟ. |
| ບໍ່ມີສຽງເບສຈາກຊັບວູບເຟີ | LPF not enabled or set too high; Phase issue; Remote bass control set to minimum. | Adjust LPF setting; Check subwoofer phase; Increase remote bass control level. |
8. ຂໍ້ມູນຈໍາເພາະ
Technical specifications for the Lanzar VIBE211 ampມີຊີວິດຊີວາ:
- Power Output (RMS @ 4 Ohms): ຂະ ໜາດ 2 x 90 ວັດ
- Power Output (Max @ 4 Ohms): ຂະ ໜາດ 2 x 180 ວັດ
- Power Output (Max Bridged @ 4 Ohms): ຂະ ໜາດ 1 x 360 ວັດ
- Power Output (RMS @ 2 Ohms): ຂະ ໜາດ 2 x 150 ວັດ
- Ampປະເພດທີ່ມີຊີວິດຊີວາ: 2 Channel Mosfet
- ການຕອບສະໜອງຄວາມຖີ່: 15 Hz - 35 kHz
- ອັດຕາສ່ວນສັນຍານຫາສຽງລົບກວນ (S/N): 90 dB
- ການໃຫ້ຄະແນນ Fuse: 15 ກ
- ຂະ ໜາດ (W x H x L): 10.25 ນິ້ວ x 2 ນິ້ວ x 8 ນິ້ວ
- ການຄວບຄຸມລະດັບການປ້ອນຂໍ້ມູນ: ຕົວແປ
- ການຄວບຄຸມ Crossover: Variable High/Low Pass
- ສະຖຽນລະພາບ: 2 Ohm Stereo Stable, Bridgeable at 4 Ohms
- ວົງຈອນປ້ອງກັນ: Advanced Power Protection LED Indicators
- ຄຸນສົມບັດເພີ່ມເຕີມ: Remote Subwoofer Bass Control, Electronic Crossover Network, Bass Boost Circuit, Soft Turn On/Off
9. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ
9.1 ຂໍ້ມູນການຮັບປະກັນ
The Lanzar VIBE211 amplifier ມາພ້ອມກັບ a 1- ປີ limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. The warranty does not cover damage caused by improper installation, accident, misuse, abuse, negligence, or unauthorized modification.
9.2 ສະຫນັບສະຫນູນລູກຄ້າ
For technical assistance, troubleshooting beyond this manual, or warranty service, please contact Lanzar customer support. Refer to the official Lanzar webສະຖານທີ່ຫຼືການຫຸ້ມຫໍ່ຜະລິດຕະພັນສໍາລັບຂໍ້ມູນຕິດຕໍ່ໃນປະຈຸບັນ.
