Android Car Player Instruction Manual

Android Car Player Instruction

ຂໍ້ມູນສະເພາະ

• power Supply Volllgo
• ການບໍລິໂພກສູງສຸດໃນປະຈຸບັນ
• ພະລັງງານອອກສູງສຸດ

1. UNIVERSAL MACHINE WIRING DIAGRAM
   
2. SPECIAL VEHICLE WIRING DIAGRAM

ຂໍ້ຄວນລະວັງການສາຍ

• 10P: Connect the reversing video input. Note: The two short wires above this line are the Bluetooth antenna and the WIFI antenna. Even if the reversing camera is not connected, this cable needs to be connected to the machine, otherwise Bluetooth and WIFI will not be connected, and carplay and Android auto will not be connected.
• 6P: Connect USB-2.
• 4P. Connect USB-1.
• 8P: Connect the CANBUS box. Note: When the product you purchased has a CANBUS box, you must connect the CANBUS box to the
• 8Pin socket on the body, otherwise some of the original car functions will not be available.
• 12P.360-degree panoramic reversing image (only supported by some models).
• 20P.RCA plug. The AMP CONT line needs to pay attention to: If your car supports speakers such as JBL or BOSE, you may need to connect this cable to the on-off control of your car’s power amplifier, and try connecting it when there is no sound.

ວິ​ທີ​ການ​ຕິດ​ຕັ້ງ​ກ້ອງ​ຖ່າຍ​ຮູບ​ກັບ​ຄືນ​ໄປ​ບ່ອນ​

ຄຳແນະນຳການສາຍສາຍໄຟສາກົນ

Tips The wiring harness colors of some models may be different. Please refer to the wire labels and the positions on the plugs and sockets.

UNIVERSAL MACHINE POWER PIN DEFINITION

ການຮຽນຮູ້ການຄວບຄຸມພວງມາໄລ
ກົດປຸ່ມຄ້າງໄວ້ເທິງພວງມາໄລຂອງລົດເດີມ ແລະຊອກຫາໄອຄອນປຸ່ມທີ່ສອດຄ້ອງກັບການເຮັດວຽກຂອງປຸ່ມເທິງພວງມາໄລ. ຄລິກໄອຄອນເພື່ອປ່ຽນສີ, ການຮຽນຮູ້ປະສົບຜົນສໍາເລັດ.

iPHONE Mirrorlink (ຮອງຮັບສະເພາະບາງລຸ້ນເທົ່ານັ້ນ)
ເມື່ອອຸປະກອນຖືກສຽບໃສ່ iPhone, ເນື້ອໃນຂອງຫນ້າຈໍໂທລະສັບຈະຖືກຄາດຄະເນໃສ່ຫນ້າຈໍລົດ.

Android Mirrorlink (ສະ​ຫນັບ​ສະ​ຫນູນ​ພຽງ​ແຕ່​ບາງ​ແບບ​)
When using an Android device, after connecting the USB data cable. you will be prompted to install the APP software. After installation, Plug the data cable again, it will enter the screen mirroring mode. And it can be operatedon both the player screen and the phone screen. Only the image transfer is successful at this time. The sound can only be  transmitted after the Bluetooth connection is successful.

Apple Car Play (Only some models support)

1. Wired connection: Just connect the USB data cable, and then it will auto matically enter the CarPlay interface.
2. Wireless connection: first tum on the bluetooth and wifi functions of the mobile phone. and then connect the bluetooth. Then it will automatically enter the CarPlay interface.
   (Note. The signal is transmitted through wifi at this ime, so even if the Bluetooth function is tumed off, it will be transmitted normally. When the wifi function is turned off. CarPlay will be disconnected.)

Android Auto (ຮອງຮັບບາງລຸ້ນເທົ່ານັ້ນ)
ຄຸນສົມບັດນີ້ບໍ່ຖືກຮອງຮັບໃນທຸກປະເທດ, ແລະ “ການບໍລິການ Google Play ຈະຕ້ອງມີຢູ່ໃນທ້ອງຖິ່ນ.

1. ຈໍາເປັນຕ້ອງໄດ້ດາວໂຫລດແລະຕິດຕັ້ງ "Android Auto" software in “Google Play”
2. ຕ້ອງໃຊ້ໂທລະສັບມືຖືທີ່ມີ Android 6.0 ຫຼືສູງກວ່າ. ຕ້ອງໃຊ້ການເຊື່ອມຕໍ່ສາຍຂໍ້ມູນທີ່ຖືກຕ້ອງ.
3. ການ​ເຊື່ອມ​ຕໍ່​ແບບ​ມີ​ສາຍ​: ພຽງ​ແຕ່​ເຊື່ອມ​ຕໍ່​ສາຍ​ຂໍ້​ມູນ USB​, ແລະ​ຫຼັງ​ຈາກ​ນັ້ນ​ມັນ​ຈະ​ເຂົ້າ​ໄປ​ໃນ​ການ​ໂຕ້​ຕອບ Android Auto ອັດ​ຕະ​ໂນ​ມັດ​.
4. Wireless connection: First turn on the Bluetooth and wifi functions of the mobile phone. and then connect the Bluetooth. Then it will automatically enter the Android Auto interface. (Note: The signal is transmitted through wifi at this time, so even if the Bluetooth function is turned off, it will be transmitted normally. When the wifi function is turned off, Android Auto will be disconnected.)

ບັນຫາທົ່ວໄປແລະການແກ້ໄຂບັນຫາທີ່ງ່າຍດາຍ

ບໍ່ສາມາດບູດໄດ້ຕາມປົກກະຕິ

1. “Yellow” “Red” “Black’ this 3 lines only connected 2 line of them, so it will not start, it should be that the yellow line is connected to the positive pole, red line to the key control line, black to the negative pole, less connection or wrong connection does not boot.
2. ສາຍລົດເດີມ ແລະ ສາຍໄຟຂອງໜ່ວຍບໍ່ສາມາດເຊື່ອມຕໍ່ສີໄດ້, ສີຂອງສາຍລົດເດີມບໍ່ໄດ້ມາດຕະຖານ, ຖ້າເຊື່ອມຕໍ່ແບບນັ້ນມັນບໍ່ພຽງແຕ່ສາມາດເປີດໄດ້ເທົ່ານັ້ນ ແຕ່ຍັງອາດຈະໄໝ້ໄດ້.
3. ປລັກສຽບລົດເດີມບໍ່ສາມາດສຽບໃສ່ເຄື່ອງໃໝ່ໄດ້ໂດຍກົງ, ເຖິງແມ່ນວ່າມັນພຽງແຕ່ສຽບຢູ່ກໍຕາມ, ມັນກໍ່ໃຊ້ບໍ່ໄດ້. ຖ້າບໍ່ດັ່ງນັ້ນມັນຈະບໍ່ຖືກເປີດຫຼືໄຟໄຫມ້.
4. 3 ສາຍຖືກເຊື່ອມຕໍ່ຖືກຕ້ອງ, ແຕ່ມັນບໍ່ boot. ກວດເບິ່ງວ່າ fuse ໃນເສັ້ນສີເຫຼືອງແມ່ນແຕກ. ຖ້າບໍ່ມີບັນຫາກັບຟິວ, ບິດສາຍໄຟສີເຫຼືອງ ແລະສີແດງເຂົ້າກັນ. ເປີດປຸ່ມແລະກົດປຸ່ມເປີດເຄື່ອງເພື່ອເບິ່ງວ່າມັນສາມາດເປີດໄດ້.
5. Every time you change the fuse, it burns. Please don’t change it again The reason is that when you first connect the positive and negative poles, the protection circuit of the unit is short-circuited. The unit can be repairedunder the guidance of our master. No basis can only be returned to the after-sales or new unit. If these are no problem, or also don’t boot, please make the final step to confirm, find a 12V battery or 12V power supply yellow and “red twist together with the positive, black to the negative pole. press the button check if it can boot or no, if you can boot, it showed that the original car line is not right connect, or there is a problem with the car line.  If it can’t be boot, the unit is broken. Does not boot unit, check the line carefully, do not blindly suspect the unit problem.

ປິດເຄື່ອງອັດຕະໂນມັດ

1. ຄວາມຜິດພາດໃນການເຊື່ອມຕໍ່ສາຍ: ຖ້າສາຍສີຟ້າ (ການສະຫນອງພະລັງງານເສົາອາກາດອັດຕະໂນມັດ) ເຊື່ອມຕໍ່ກັບສາຍໄຟຂອງຫນ່ວຍ, ການປິດອັດຕະໂນມັດຈະເກີດຂຶ້ນ. ກະລຸນາປະຕິບັດຕາມວິທີການສາຍໄຟທີ່ຖືກຕ້ອງເພື່ອແກ້ໄຂບັນຫາ.
2. ປະລິມານtage ແມ່ນບໍ່ຫມັ້ນຄົງ: ກະລຸນາຊອກຫາ 12V-5A ທີ່ຫນຶ່ງແມ່ນການສະຫນອງພະລັງງານແລະການທົດສອບຄືນໃຫມ່ເພື່ອເບິ່ງວ່າມັນຈະປິດອັດຕະໂນມັດ. ຖ້າມັນບໍ່ປິດອັດຕະໂນມັດຫຼັງຈາກການທົດສອບ, ກະລຸນາປ່ຽນການສະຫນອງພະລັງງານ. ຖ້າຫາກວ່າມັນຈະປິດອັດຕະໂນມັດ, ມັນເປັນບັນຫາກັບຫນ່ວຍບໍລິການ.

ມີສິ່ງລົບກວນ

1. ລຳໂພງຕົ້ນສະບັບນ້ອຍເກີນໄປ. ເມື່ອປະລິມານຂອງຫນ່ວຍບໍລິການແມ່ນຫັນຂຶ້ນ. ຈະມີສິ່ງລົບກວນ.
   ການແກ້ໄຂ: ເມື່ອປ່ຽນລຳໂພງ ຫຼືຟັງເພງ, ລະດັບສຽງບໍ່ຄວນໃຫຍ່ເກີນໄປ.

ສາຍຂອງລໍາໂພງແມ່ນຮາກຖານ.
ການແກ້ໄຂ: ເອົາສາຍລໍາໂພງທາດເຫຼັກ. ເຊື່ອມຕໍ່ໂດຍກົງກັບສາຍລໍາໂພງຂອງຫນ່ວຍບໍລິການ.

ບໍ່ສາມາດໃຊ້ການຄວບຄຸມໄລຍະໄກໄດ້

1. Test method Turn on the camera of the mobile phone and align the light of the remote control then press the button of the remote control to see if the phone will light up. If it is not lit there will be no power. Replace the battery: If it is it there is electricity, which proves that there is no problem with the remote control.

ບໍ່ສາມາດບັນທຶກການຕັ້ງຄ່າໄດ້ (ບໍ່ມີໜ່ວຍຄວາມຈຳ)

1. ເສັ້ນສີເຫຼືອງແລະເສັ້ນສີແດງແມ່ນເຊື່ອມຕໍ່ກັນ (ແຍກສີເຫຼືອງເປັນບວກ, ສີແດງກັບການຄວບຄຸມທີ່ສໍາຄັນ).
2. ສີເຫຼືອງແລະສີແດງແມ່ນປີ້ນກັບກັນ (ພຽງແຕ່ປ່ຽນຕໍາແຫນ່ງ).

Bluetooth ບໍ່ເຮັດວຽກ
ເປີດເຄື່ອງ, ຊອກຫາຊື່ Bluetooth ຂອງເຄື່ອງໂດຍໃຊ້ Bluetooth ຂອງໂທລະສັບມືຖື, ແລ້ວຄລິກເຊື່ອມຕໍ່, ຫຼັງຈາກເຊື່ອມຕໍ່ແລ້ວ, ທ່ານສາມາດຮັບສາຍ ຫຼື ຫຼິ້ນເພງຜ່ານ Bluetooth ໄດ້.

ຜະລິດຕະພັນປ່ອຍຄວັນຢາສູບ
ປ່ຽນຟິວ FUSE, ຖ້າບັນຫາບໍ່ສາມາດແກ້ໄຂໄດ້, ວົງຈອນພາຍໃນໄດ້ຖືກໄຟໄຫມ້. ຕ້ອງການການບໍລິການຫຼັງການຂາຍ.

ສຽງບໍ່ສາມາດປັບໄດ້

1. ກະລຸນາຣີເຊັດໜ່ວຍ ຫຼືຖອດສາຍໄຟອອກແລ້ວສຽບໃສ່.
2. The Volume knob is broken, and it can be replaced.

ກ້ອງຫຼັງບໍ່ສະແດງ

1. ສາຍໄຟຜິດ ຫຼື ສາຍໄຟຂາດ.

ວິທີການເຊື່ອມຕໍ່ກ້ອງຖ່າຍຮູບ:

1. ຊອກຫາອຸປະກອນເສີມ: 1 ກ້ອງຖ່າຍຮູບ + 1 ສາຍໄຟ +1 ສາຍວິດີໂອ.
2. Find the port of the wiring. First find the reverse control line on the power line of the unit. The control line is a pink line. Connect this line to the positive pole of 12V and the screen will turn blue. And then find the back of the unit the CAM video input interface, find the positive and negative of the backup light.
3. ມີສອງຊັອກເກັດຢູ່ໃນກ້ອງຖ່າຍຮູບ, ເຕົ້າສຽບສີແດງເຊື່ອມຕໍ່ກັບສາຍໄຟ, ສີເຫຼືອງຖືກໃສ່ເຂົ້າໄປໃນສາຍວິດີໂອ, ສາຍສີແດງຂອງສາຍໄຟແລະສາຍຂອງສາຍວິດີໂອແມ່ນ screwed ຮ່ວມກັນກັບຂົ້ວບວກຂອງ. ປີ້ນກັບamp, and the black wire of the power cable is not used. connected, the other end of the video cable is connected to the CAM video input interface on the back of the unit. The red line coming out of the video line is connected to the reversing control line of the power line.
4. ກ້ອງຖ່າຍຮູບແຕກ. ຖ້າ lamp ທີ່ ຖືກ ສາຍ ຢ່າງ ຖືກ ຕ້ອງ ກັບ ກ້ອງ ຖ່າຍ ຮູບ ບໍ່ ໄດ້ lit. ມັນ​ຈະ​ຖືກ​ແຍກ​ອອກ​ແລະ​ທົດ​ແທນ​ທີ່​ມີ​ອັນ​ໃຫມ່​.

ອຸປະກອນ USB ບໍ່ສາມາດຫຼິ້ນໄດ້
Format USB flash disk, ແລະ file ລະບົບຖືກເລືອກເປັນ: FAT32, ດາວໂຫຼດໃໝ່ ຫຼືສອງເພງແລ້ວລອງໃໝ່ອີກຄັ້ງ. ຖ້າມັນຍັງໃຊ້ບໍ່ໄດ້, ກະລຸນາປ່ຽນ USB flash drive.

FM ບໍ່ໄດ້ຮັບສະຖານີວິທະຍຸ

1. The antenna plug is not fully inserted, the antenna is disconnect or the line is disconnected.
2. Search station, press AS will automatically search or press the before or after button. Can’t solve the above 2 points. Please unplug the antenna plug and find a screwdriver or a metal strip to insert into the antenna.

ບໍ່ມີສຽງທັນທີຫຼັງຈາກການຕິດຕັ້ງ
Dear customers, the unit has been tested before shipment. If there is no sound, it is usually a wiring error or the original car speaker wire is short- circuited with iron. According to the steps to check it:

1. ກວດເບິ່ງວ່າສາຍລຳໂພງແມ່ນສາຍລັດວົງຈອນ ແລະເຊື່ອມຕໍ່ຫຼືບໍ່. ກະລຸນາເຊື່ອມຕໍ່ຄືນໃໝ່ຖ້າທ່ານມີວົງຈອນສັ້ນ.
2. Check how many speaker cables according to the original speaker cable if there are only 2 speaker cables, to prove that the original car line does not match our unit, you need to re-route the original car line. One speaker must lead to 2 speaker wires. 2 speakers must be have 4 speaker cables to available.

ບໍ່ມີສຽງຫຼັງຈາກໃນຂະນະທີ່ເປັນ
Disconnect all the speaker cable from the unit (do not remove them), and then find an external speaker to receive the gray and purple of the tail line of the unit.Check any group, and then try to see if there is any sound If there is a sound, it is proven that the car’s speaker line is short-circuited with iron or the speaker is damaged. If there is no sound, the unit is broken.

ເຄັດລັບ: If the device is updated, the functions are subject to change without prior notice