1. ບົດແນະນຳ
The LEXON VERO Integrated Carbon Road Handlebars are engineered for road cycling enthusiasts, offering a superlight, one-piece carbon construction with full inner cable routing for enhanced aerodynamics and a clean aesthetic. This manual provides essential information for the proper installation, safe usage, and effective maintenance of your new handlebars.
ຮູບພາບ: ຫຼາຍກວ່າview of the LEXON VERO Integrated Carbon Road Handlebars, highlighting its superlight design, carbon UD construction, integrated cockpit, and titanium alloy components. It also notes a weight of 300g ± 10g and a 1-year warranty.
2. ຂໍ້ມູນຈໍາເພາະ
| ຄຸນລັກສະນະ | ລາຍລະອຽດ |
|---|---|
| ຍີ່ຫໍ້ | ເລຊອນ |
| ຕົວແບບ | VERO |
| ຂອບເຂດຂອງການນໍາໃຊ້ | ລົດຖີບຖະໜົນ |
| ວັດສະດຸ | Carbon UD, Superlight Layup (Full Carbon T1000) |
| Width (Center of Hoops, W) | 340mm, 360mm, 380mm, 400mm, 420mm |
| Width (Center of Drops, W1) | 360mm, 380mm, 400mm, 420mm, 440mm |
| Stem Length (N) | 80mm, 90mm, 100mm, 110mm, 120mm, 130mm |
| ລຸດລົງ | 130ມມ |
| ບັນລຸ | 75ມມ |
| Steerer Diameter | 1-1/8" (28.6mm) |
| Clamp ເສັ້ນຜ່າສູນກາງ | IC (Integrated Cockpit) |
| ນ້ຳໜັກ (ປະມານ) | 300±10g (for 360*100mm, accessories not included) |
| ຄຸນສົມບັດ | Integrated cables (mechanical and electronic groupsets), Aero optimized and wind tunnel tested shapes, Compact bend, Full carbon construction, Full Inner Cable Routing |
| Fatigue Tests | Unidirectional Load: 280N, >100,000 cycles. Bidirectional Load: 400N, >100,000 cycles. Result: Zero failure. |
| ການທົດສອບຜົນກະທົບ | Withstands 15kg weights dropped from 550mm. |
Image: Detailed size chart for the LEXON VERO handlebars, showing W1 (center of drops), W (center of hoops), Reach, Drop, Stem Angle, and Stem Length (N) for various widths (360mm, 380mm, 400mm, 420mm, 440mm).
Image: Table showing approximate weights for different handlebar sizes (e.g., 360x100mm: 300g, 440x100mm: 335g), noting that accessories are not included in these weights.
3. ເນື້ອໃນຊຸດ
Your LEXON VERO Integrated Carbon Road Handlebars package includes the following items:
- LEXON VERO Integrated Carbon Road Handlebar
- Computer Mount (compatible with Garmin, Bryton)
- ວົງເລັບກ້ອງຖ່າຍຮູບ
- screws ການຕິດຕັ້ງ
- ຝາເທິງ
- 10mm Top Cap for Full Inner Cable
- 8mm Top Cap for Regular Inner Cable
- Cable Guide Ring
- Aero Spacers (5mm, 7mm, 10mm, 15mm)
- Headset Top Cap
- Compression Ring (8mm)
- Carbon Aero Top Cap + Titanium Bolt
Image: A visual list of included accessories, including the computer mount (for Garmin and Bryton), camera bracket, various mounting screws, top cover, 10mm and 8mm top caps for different cable routings, a cable guide ring, and various aero spacers (5mm, 7mm, 10mm, 15mm).
ຮູບພາບ: ອື່ນ view of the accessories, specifically showing the spacers sets, headset top cap, and computed mount.
4. ການຕິດຕັ້ງ
Proper installation is crucial for safety and performance. If you are unsure about any steps, it is highly recommended to consult a professional bike mechanic.
4.1 ການຕິດຕັ້ງມືຈັບ
- Ensure your bike's steerer tube is compatible (28.6mm / 1-1/8" OD1). Refer to the compatibility section.
- Carefully slide the handlebar onto the steerer tube.
- Install the appropriate aero spacers (5mm, 7mm, 10mm, 15mm) and headset top cap to achieve your desired stack height.
- Secure the handlebar using the integrated lock system, ensuring the AL7075 plate and Titanium locking bolts are correctly tightened to the manufacturer's recommended torque specifications.
Image: Illustration of integrated aero spacers designed for seamless integration with the handlebar for a clean, aerodynamic front-end profile.
4.2 ເສັ້ນທາງສາຍໄຟ
The VERO handlebars support full inner cable routing for a clean and aerodynamic setup. Plan your cable paths carefully before installation.
- Route brake and shifter cables through the internal channels of the handlebar.
- Use the provided 10mm Top Cap for full inner cable routing or the 8mm Top Cap for regular inner cable routing, as appropriate for your setup.
- Ensure cables move freely without kinks or excessive friction.
Image: Diagram illustrating the precise hole positions and recommended routing for both full inner cable and regular cable systems, ensuring compatibility and a neat setup.
4.3 ການຕິດຕັ້ງອຸປະກອນເສີມ
The integrated computer mount allows for easy attachment of cycling computers, cameras, and lights.
- Attach the computer mount to the designated area on the handlebar using the provided screws.
- Secure your Garmin or Bryton device to the computer mount.
- Use the camera bracket to attach action cameras or flashlights as needed.
Image: Shows a Bryton speed meter and a Garmin device mounted on the integrated bracket, demonstrating easy installation of speedometers, flashlights, and GoPros.
Image: Highlights the triple mount, single solution design of the speedometer bracket, securely and neatly mounting your computer, light, and action camera.
4.4 Handlebar Tape Installation (RYET Bar Tape Manual)
This section details the process for wrapping handlebar tape, ensuring a secure and comfortable grip.
- **Preparation & Tools:** You will need bar tape, two finishing tapes (included), two end plugs (included), scissors, and electrical tape (optional for a cleaner finish).
- **Wrapping Instructions (Right Side):**
- **Start:** Unwrap the tape backing about 15cm. Begin wrapping at the bottom of the drop (end of the handlebar), leaving the first 2-3 cm of tape overhanging the bar end.
- **Direction:** Wrap outward to inward (counter-clockwise on the right side). Pull the tape taut at a consistent, moderate tension as you wrap.
- **Overlap:** Overlap each preceding wrap by about one-third to one-half of the tape's width.
- **Around the Brake Lever:** When you reach the brake lever clamp, wrap behind the lever, then in front, to create a secure, neat hood.
- **Finish:** Continue wrapping until you reach the top of the handlebar near the stem. Cut the tape at a slight angle.
- **Wrapping Instructions (Left Side):**
- Repeat Step 2, but wrap inward to outward (clockwise on the left side) for symmetry.
- Ensure both sides end at the same position near the stem.
- **Finishing:**
- Use the supplied finishing tape to secure the end neatly. Wrap it tightly 2-3 times.
- Push the end plugs firmly into the bar ends, trapping the overhanging tape inside.
- For extra security, you may wrap a final layer of electrical tape over the finishing tape.
Image: Detailed instructions for wrapping handlebar tape, including preparation, right side wrapping, left side wrapping, and finishing steps.
5. ບັນທຶກຄວາມເຂົ້າກັນໄດ້
- **Steerer Tube:** This VERO Integrated Handlebar is designed for 28.6mm (1-1/8" OD1) steerer tubes ONLY. It is NOT compatible with oversized steerer tubes (e.g., 31.8mm / OD2).
- **Head Tube:** The cone spacer included is designed only for standard round headtubes. It is NOT compatible with special shaped (aero/oval) headtubes.
Image: Visual representation of steerer tube compatibility, clearly indicating that 28.6mm (OD1) is compatible, while 31.8mm (OD2) is not.
Image: A warning note stating that the cone spacer is designed only for standard round headtubes and is not compatible with special shaped (aero/oval) headtubes.
6. ການນຳໃຊ້
The LEXON VERO handlebars are designed to provide optimal power and control for road cycling, offering:
- Enhanced control for technical descents.
- Increased comfort for long distances.
- Versatility for any hand position.
- Built for every adventure.
Image: Highlights the ergonomic benefits of the handlebar, including ergonomic wrist alignment, increased control on rough descents, and a more comfortable, powerful riding position.
6.1 Non-Slip Coating
The handlebar features an anti-skid design with a non-slip coating to prevent potential safety hazards and ensure a secure grip during your ride.
Image: Illustrates the non-slip coating on the handlebar, designed to enhance grip and safety.
ຮູບພາບ: ໃກ້ຊິດ view of the anti-skid design on the handlebar surface.
7. ບໍາລຸງຮັກສາ
7.1 Handlebar Care & Replacement
- Keep the handlebar tape clean with a damp cloth. Avoid harsh chemicals, which can damage the material.
- Replace handlebar tape when it becomes worn, torn, or loses its cushioning to maintain comfort and grip.
7.2 User-Serviceable Lock System
The VERO handlebar features a user-serviceable lock system built with a replaceable AL7075 plate and Titanium locking bolts. This innovative design ensures long-term reliability and easy maintenance, allowing for quick part replacement without discarding the whole assembly.
Image: Diagram illustrating the user-serviceable lock system with replaceable AL7075 plate and Titanium locking bolts for easy maintenance.
8. ການແກ້ໄຂບັນຫາ
- **Handlebar not fitting steerer tube:** Ensure your steerer tube is 28.6mm (1-1/8" OD1). The VERO handlebar is not compatible with 31.8mm (OD2) steerer tubes.
- **Headset cone spacer not fitting:** The cone spacer is designed for standard round headtubes. It will not fit special shaped (aero/oval) headtubes.
- **Loose handlebar tape:** Re-wrap the tape following the instructions in Section 4.4, ensuring consistent tension and proper overlap. Replace tape if it is old or damaged.
9. ຄໍາແນະນໍາຜູ້ໃຊ້
- **Professional Installation:** For safety and optimal performance, if you are unsure about the installation process, it is always best to consult a qualified bike mechanic.
- **Check Compatibility:** Double-check your bike's steerer tube diameter (28.6mm / 1-1/8") and headtube shape (standard round) before purchasing to ensure full compatibility.
- **Choose Correct Size:** Carefully consider the handlebar width (W and W1) and stem length (N) options to select the size that best suits your riding style and body geometry for maximum comfort and control.
- **Cable Management:** Take your time with internal cable routing to ensure smooth operation of brakes and shifters and to maintain the handlebar's aerodynamic benefits.
10. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ
10.1 ຂໍ້ມູນການຮັບປະກັນ
The LEXON VERO Integrated Carbon Road Handlebars come with a **one-year (12 months) warranty** from the date of purchase. This warranty covers any breaks or fractures that might occur in any area during correct use.
ການຮັບປະກັນບໍ່ໄດ້ກວມເອົາ:
- ການປະທະກັນ
- ອຸບັດເຫດ
- ຜົນກະທົບທີ່ເຂັ້ມແຂງ
- Falls on the frame
- ການນໍາໃຊ້ທີ່ບໍ່ຖືກຕ້ອງ
- ການລະເລີຍ
- ການປະກອບທີ່ບໍ່ເຫມາະສົມ
In situations where the damage caused is not covered by the guarantee, lifetime crash replacements are offered.
Note: Shipping costs and possible taxes for after-sales services will be borne by the buyer.
Image: Details of the 1-year warranty, including what is covered (breaks/fractures during correct use) and what is not covered (collision, accidents, improper use, etc.). It also mentions lifetime crash replacements.
10.2 ສະຫນັບສະຫນູນດ້ານວິຊາການ
For further technical assistance or inquiries, please refer to the official LEXON support channels. You can also view the comprehensive user manual in PDF format for detailed guidance:
