ຄູ່ມືການໃຊ້ງານຟິມປ່ອຍ HALOT-SKY/LD-006 FEP ຢ່າງເປັນທາງການຂອງ Creality

1. ບົດແນະນຳ

This manual provides detailed instructions for the installation, use, and maintenance of the Creality Official LD-006 FEP Release Film. This high-quality FEP film is designed for use with compatible Creality 3D printers, ensuring optimal performance and print quality. Please read this manual thoroughly before installation and use.

2. ຂໍ້ມູນຈໍາເພາະຂອງຜະລິດຕະພັນ

The Creality FEP Release Film is engineered for high performance in resin 3D printing. Key features and specifications are detailed below:

ຄຸນ​ນະ​ສົມ​ບັດ​ຜະ​ລິດ​ຕະ​ພັນ​:

• High Purity FEP Resin: Made from high purity FEP resin (vinyl chloride propylene copolymer), offering excellent non-viscosity, heat resistance, electrical insulation, mechanical properties, and wear resistance.
• High Transmittance: UV transmittance exceeds 95%, ensuring precise and high-quality 3D prints.
• Stable Release Force: Features uniform coating and stable release force for efficient separation of most resins.
• ພື້ນຜິວລຽບ: Designed to be free of wrinkles, scratches, and bubbles, meeting the release requirements for various products.
• Excellent Flexibility and Ductility: Boasts up to 300% ductility and can withstand 10,000 bend tests, ensuring durability and longevity.
• High Cleanliness: Produced in a no-dust workshop to maintain optimal quality.

3. ການຕິດຕັ້ງ

Follow these steps carefully to install the FEP release film in your resin vat:

1. Remove Old Film: First, remove the 14 screws located at the bottom of the resin vat. Carefully take out the broken or old release film.
2. Position New Film: Place the new FEP release film between the two steel rims of the resin vat frame. Ensure it is centered and flat.
3. Secure Film: Finally, put the assembled steel frame back into the resin vat and tighten the 14 screws. Ensure all screws are securely fastened to prevent resin leaks.

ວິ​ດີ​ໂອ​ຄູ່​ມື​ການ​ຕິດ​ຕັ້ງ​:

4. ບໍາລຸງຮັກສາ

Proper maintenance of your FEP film is crucial for consistent print quality and extending its lifespan:

• ການກວດກາປົກກະຕິ: Before each print, inspect the FEP film for any signs of damage, such as punctures, scratches, or cloudiness. Replace the film if any damage is observed.
• ທໍາຄວາມສະອາດ: After printing, carefully clean any residual resin from the FEP film using a soft cloth and isopropyl alcohol (IPA). Avoid using sharp objects or abrasive materials that could scratch the film.
• ການຈັດການທີ່ອ່ອນໂຍນ: Always handle the FEP film with care. Avoid touching the printing surface directly with your fingers to prevent oil transfer.
• ການເກັບຮັກສາ: Store unused FEP films in a clean, dry, and dust-free environment, away from direct sunlight and extreme temperatures.

5. ການແກ້ໄຂບັນຫາ

If you encounter issues with your FEP film or prints, consider the following:

• Prints Not Sticking to Build Plate: Ensure the FEP film is clean and free of resin residue. Check if the film is properly tensioned and installed. Adjust print settings such as bottom layer exposure time.
• Resin Leaks: Verify that all 14 screws securing the FEP film in the resin vat are tightened correctly. Inspect the film for any punctures or tears that could cause leaks.
• Cloudy or Damaged Film: Over time, FEP film can become cloudy or damaged from repeated use. This can affect print quality. Replace the film if it shows significant wear or damage.
• Print Failures/Adhesion Issues: Check for proper FEP film tension. Too loose or too tight can cause issues. Ensure the resin vat is clean and the film is free of dust or debris.

6. ຄໍາແນະນໍາຜູ້ໃຊ້

Here are some helpful tips from other users to enhance your experience:

• ກວດສອບຄວາມເຂົ້າກັນໄດ້: While this FEP film is designed for LD-006, HALOT-SKY, HALOT-LITE, and HALOT SKY 2022, always double-check your printer's specifications for FEP film size and compatibility. For example, some users have inquired about compatibility with the Creality Halot One Plus; always confirm dimensions and mounting method for other models.
• Protective Layers: Some FEP films come with protective layers on both sides. Remember to peel these off before installation for optimal transparency and performance.
• ການຮັດແໜ້ນຢ່າງສະເໝີພາບ: When tightening the screws during installation, do so in a cross-pattern to ensure even tension across the film and prevent wrinkles.

7. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

This Creality FEP Release Film comes with a 1-year warranty. For any technical assistance, warranty claims, or further inquiries, please contact Creality 3D Official Store customer support. Ensure you retain your proof of purchase for warranty purposes.

ຂໍ້ມູນຕິດຕໍ່: Please refer to the official Creality 3D webເວັບໄຊທ໌ ຫຼື ແພລດຟອມການຊື້ຂອງທ່ານ ສຳລັບລາຍລະອຽດການຕິດຕໍ່ຝ່າຍສະໜັບສະໜູນລູກຄ້າທີ່ທັນສະໄໝທີ່ສຸດ.