Alphacool Core RX 9070 XT TUF + Prime GPU Water Block with Backplate

1. ຜະລິດຕະພັນເກີນview

The Alphacool Core RX 9070 XT TUF + Prime GPU Water Block is designed for the latest AMD Radeon RX generation graphics cards. This water block is part of the Core product series, offering high-quality construction and optimized cooling performance. It features a copper cooler milled from a single piece, a brass connection terminal with a nylon cover, and chrome plating for durability. The integrated acrylic top allows for impressive aRGB lighting. The design includes an optimized cooler base and nozzle for efficient heat transfer.

Figure 1: Alphacool Core RX 9070 XT TUF + Prime GPU Water Block with Backplate, showing the overall design and clear acrylic top.

2. ສິ່ງທີ່ຢູ່ໃນກ່ອງ

ກະລຸນາກວດສອບວ່າອົງປະກອບທັງໝົດມີຢູ່ກ່ອນທີ່ຈະເລີ່ມການຕິດຕັ້ງ.

• 1x GPU Water Block
• ແຜ່ນຮອງ 1x
• screws ແລະເຄື່ອງຊັກຜ້າ
• ເຄື່ອງເຮັດຄວາມຮ້ອນ
• ການວາງຄວາມຮ້ອນ
• RGB Connection Cable (if applicable)

3. ການຕິດຕັ້ງແລະການຕິດຕັ້ງ

This section provides detailed instructions for installing your Alphacool Core GPU Water Block. Ensure your system is powered off and disconnected from the mains before proceeding. It is recommended to consult your graphics card's manual for disassembly instructions.

3.1 ການກະກຽມ

1. ເກັບ​ກໍາ​ເຄື່ອງ​ມື​: You will need a small Phillips head screwdriver, isopropyl alcohol, and lint-free cloths.
2. Disassemble GPU: Carefully remove the stock cooler from your graphics card. This typically involves unscrewing the mounting screws around the GPU core and removing any fan headers or RGB cables.
3. Clean GPU: Use isopropyl alcohol and a lint-free cloth to thoroughly clean the GPU die and memory modules, removing all traces of old thermal paste and thermal pads.

3.2 ການນຳໃຊ້ວັດສະດຸຄວາມຮ້ອນ

Proper application of thermal paste and pads is critical for optimal cooling performance.

Figure 2: The copper cooler base of the water block, where thermal paste and pads are applied.

1. ນຳໃຊ້ຢາລະບາຍຄວາມຮ້ອນ: Apply a small amount of thermal paste (pea-sized dot or thin line) to the center of the GPU die. Do not spread it manually; the pressure from the water block will distribute it evenly.
2. ໃຊ້ຜ້າກັນຄວາມຮ້ອນ: Cut the provided thermal pads to the correct sizes according to the instruction diagram (usually included with the product, or refer to Alphacool's website for a specific model diagram). Carefully place them on the memory modules and VRM components on the graphics card PCB. Ensure good contact and no air bubbles.

3.3 ການຕິດຕັ້ງບລັອກນໍ້າ

Figure 3: Underside of the water block showing mounting holes for secure attachment to the GPU PCB.

1. ຕຳແໜ່ງຂອງບລັອກນ້ຳ: Carefully align the water block with the mounting holes on the graphics card PCB. Lower the block straight down onto the GPU, ensuring the thermal paste and pads make proper contact.
2. ບລັອກນໍ້າທີ່ປອດໄພ: Insert the provided mounting screws through the back of the PCB and into the water block. Tighten them in a diagonal pattern (e.g., top-left, bottom-right, top-right, bottom-left) until snug. Do not overtighten.

3.4 ການຕິດຕັ້ງແຜ່ນຮອງດ້ານຫຼັງ

The backplate provides structural support and additional cooling for the rear of the PCB.

Figure 4: The aluminum backplate, designed to cover the entire back of the GPU PCB.

1. Apply Backplate Thermal Pads: If included, apply thermal pads to the designated areas on the backplate to make contact with the rear of the PCB components.
2. ຕິດຕັ້ງແຜ່ນຮອງດ້ານຫຼັງ: Align the backplate with the mounting holes on the rear of the graphics card. Secure it with the remaining screws, tightening them evenly.

3.5 Connecting to the Cooling Loop

ຮູບທີ 5: ທາງເທິງ view of the water block, highlighting the G1/4 inch connection ports for liquid cooling.

1. ຕິດຕັ້ງອຸປະກອນເສີມ: Screw G1/4 inch fittings (not included) into the inlet and outlet ports of the water block. Ensure they are hand-tightened securely.
2. ເຊື່ອມຕໍ່ທໍ່: Connect your liquid cooling tubing to the installed fittings, ensuring a secure and leak-free connection.
3. ເຊື່ອມຕໍ່ RGB (ທາງເລືອກ): If your water block includes aRGB lighting, connect the provided RGB cable to a compatible 3-pin 5V aRGB header on your motherboard or a dedicated RGB controller.
   

   ຮູບທີ 6: ຕົວຢ່າງample of the integrated aRGB lighting in the water block.

4. ຄໍາແນະນໍາການດໍາເນີນງານ

1. ການທົດສອບຮົ່ວ: Before powering on your computer, perform a thorough leak test of your entire liquid cooling loop. It is highly recommended to use an air pressure tester for at least 15-30 minutes. Alternatively, fill the loop with coolant and run the pump for several hours with the system powered off, checking for any leaks.
2. ການເລີ່ມຕົ້ນເບື້ອງຕົ້ນ: Once leak testing is complete and no leaks are detected, power on your system. Monitor coolant temperatures and GPU temperatures using appropriate software.
3. ການຕິດຕາມ: Regularly monitor your system's temperatures to ensure optimal performance. High temperatures may indicate issues with coolant flow, air bubbles, or insufficient thermal contact.

5. ບໍາລຸງຮັກສາ

• ການປ່ຽນນໍ້າຢາຫລໍ່ເຢັນ: ແນະນຳໃຫ້ປ່ຽນນ້ຳຢາຫຼໍ່เย็นໃນລະບົບຫຼໍ່เย็นທຸກໆ 6-12 ເດືອນ, ຂຶ້ນກັບປະເພດ ແລະ ການນຳໃຊ້ນ້ຳຢາຫຼໍ່ເຢັນ.
• ທໍາຄວາມສະອາດລະບົບ: Periodically inspect your water block and other loop components for any signs of buildup or corrosion. If necessary, disassemble and clean with distilled water and a soft brush.
• ການກຳຈັດຂີ້ຝຸ່ນ: Keep your system's radiators and fans clean from dust to maintain efficient heat dissipation.

6. ການແກ້ໄຂບັນຫາ

7. ຂໍ້ມູນຈໍາເພາະ

• ຕົວແບບ: 14779
• ຂະໜາດສິນຄ້າ (L x W x H): 220.00 x 144.50 x 33.07 ມມ (8.66"L x 5.69"W x 1.3"H)
• ວິທີການເຮັດຄວາມເຢັນ: ນ້ໍາ
• ວັດສະດຸ: Copper (cooler), Brass (connection terminal), Nylon (cover), Aluminum (backplate), Acrylic (top)
• ປະເພດຕົວເຊື່ອມຕໍ່: G1/4 inch threads for fittings
• RGB: Addressable RGB (3-Pin 5V)
• ນ້ໍາຫນັກລາຍການ: ປະມານ 1.81 ກິໂລ (4 ປອນ)

8. ຄວາມເຂົ້າກັນໄດ້

This water block is compatible with the following graphics card models:

• Asus Prime Radeon RX 9070 OC Edition 16GB GDDR6
• Asus TUF Gaming Radeon RX 9070 OC Edition 16GB GDDR6
• Asus Prime Radeon RX 9070 XT OC Edition 16GB GDDR6
• Asus TUF Gaming Radeon RX 9070 XT OC Edition 16GB GDDR6

Always verify your specific graphics card model against the compatibility list before purchase and installation.

9. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

ຜະລິດຕະພັນ Alphacool ແມ່ນຜະລິດຕາມມາດຕະຖານສູງ ແລະ ມາພ້ອມກັບການຮັບປະກັນຂອງຜູ້ຜະລິດ. ສຳລັບເງື່ອນໄຂ ແລະ ຂໍ້ກຳນົດການຮັບປະກັນສະເພາະ, ກະລຸນາອ້າງອີງເຖິງ Alphacool ຢ່າງເປັນທາງການ webເວັບໄຊທ໌ຫຼືຕິດຕໍ່ສະຫນັບສະຫນູນລູກຄ້າຂອງພວກເຂົາ.

For technical assistance, troubleshooting, or warranty claims, please visit the Alphacool support portal or contact their customer service department.

• ທາງການ Webເວັບໄຊ: www.alphacool.com
• ສະຫນັບສະຫນູນ: ອ້າງອີງເຖິງພາກສະຫນັບສະຫນູນກ່ຽວກັບເຈົ້າຫນ້າທີ່ webເວັບໄຊ.