1. ບົດແນະນຳ
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Hyuduo 30A PWM Solar Charge Controller. This device is designed to manage the power flow from your solar panels to your battery bank, ensuring efficient charging and protecting your battery from overcharge and over-discharge. It is suitable for 12V and 24V solar systems.
ຮູບ 1: ດ້ານຫນ້າ view of the Hyuduo 30A PWM Solar Charge Controller.
2. ຂໍ້ມູນຄວາມປອດໄພ
Please read all safety instructions carefully before installation and operation. Failure to follow these instructions may result in personal injury or damage to the controller or other equipment.
- ໃຫ້ແນ່ໃຈວ່າຫມໍ້ໄຟມີປະລິມານພຽງພໍtage for the controller to recognize the correct battery type during first installation.
- Install the controller as close as possible to the battery to minimize voltage drop from long wires.
- This controller is designed for lead-acid batteries (OPEN, AGM, GEL). It is not suitable for other battery types.
- Ensure all connections are tight and correct to prevent damage.
- ຢ່າຖອດປະກອບ ຫຼື ພະຍາຍາມສ້ອມແປງຕົວຄວບຄຸມດ້ວຍຕົນເອງ. ຕິດຕໍ່ພະນັກງານທີ່ມີຄຸນວຸດທິເພື່ອຂໍຄວາມຊ່ວຍເຫຼືອ.
- Keep the controller away from water, flammable gases, and corrosive substances.
3. ຄຸນລັກສະນະຂອງຜະລິດຕະພັນ
The Hyuduo 30A PWM Solar Charge Controller incorporates advanced technology for reliable solar power management:
- Industrial Grade Master Control Chip: Ensures stable and efficient operation with complete 3-stagການຈັດການສາກໄຟ PWM.
- ຈໍ LCD ຂະຫນາດໃຫຍ່: Provides clear status and data, allowing easy mode switching and parameter configuration.
- ການປົກປ້ອງທີ່ສົມບູນແບບ: Built-in overcurrent, short circuit, open circuit, and reverse connection protection. All protections are self-recovery type, preventing damage to the controller.
- MOS Anti-Backup Circuit: Features ultra-low heat generation, ensuring optimal device performance and longevity.
- ການກໍ່ສ້າງທົນທານ: Made from excellent ABS material, providing impact resistance, high ignition point, and anti-aging/erosion properties.
- USB Output: Two USB output ports (5V, 1A maximum) for charging external devices.
4. ເນື້ອໃນຊຸດ
ກະລຸນາກວດສອບວ່າລາຍການທັງໝົດມີຢູ່ໃນຊຸດຂອງທ່ານ:
- Hyuduo 30A PWM Solar Charge Controller
- ຄູ່ມືຜູ້ໃຊ້ (ເອກະສານນີ້)
5. ຜະລິດຕະພັນເກີນview
Familiarize yourself with the components of your solar charge controller.
ຮູບທີ 2: ທາງເທິງ view showing connection terminals and buttons.
ຮູບທີ 3: ລາຍລະອຽດ view ຂອງຈໍສະແດງຜົນ LCD ແລະປຸ່ມຄວບຄຸມຕ່າງໆ.
5.1. ຈໍສະແດງຜົນ ແລະປຸ່ມຕ່າງໆ
The large LCD display shows real-time system status and parameters. The three buttons below the display allow for navigation and setting adjustments:
- ປຸ່ມຊ້າຍ: ເມນູ / ກະລຸນາໃສ່
- ປຸ່ມກາງ: ເພີ່ມ / ເພີ່ມຂື້ນ
- ປຸ່ມຂວາ: ຫຼຸດລົງ / ຫຼຸດລົງ
6. ຂໍ້ມູນຈໍາເພາະ
| ພາລາມິເຕີ | ມູນຄ່າ |
|---|---|
| ລະບົບ Voltage | 12V, 24V Automatic Adaptation |
| ປະເມີນຄ່າກະແສໄຟຟ້າ | 10A (Note: Product title indicates 30A, please refer to product label for actual rating) |
| Maximum Photovoltaic Voltage | Max 23V for 12V Battery; Max 46V for 24V Battery |
| Light Control On Threshold | PV Panel 8V (Light Control On with delay) |
| Light Controlled Off Threshold | PV Panel 8V (Light Controlled Off with delay) |
| USB Output | 2 Way USB Output, 5V, 1A (Maximum) |
| ອຸນຫະພູມປະຕິບັດການ | -35°C ເຖິງ +60°C |
| ວັດສະດຸ | ABS |
| ຂະໜາດແພັກເກັດ | 5.51 x 3.15 x 1.57 ນິ້ວ |
| ນ້ໍາຫນັກລາຍການ | 5.3 ອອນ |
Note: The product description lists a Rated Discharge Current of 10A, while the product title specifies 30A. Please verify the actual rating on the product label or packaging.
7. ການຕິດຕັ້ງ (Setup)
Follow these steps for proper installation of your solar charge controller. Ensure all power sources are disconnected before making any connections.
ຮູບ 4: ດ້ານຫລັງ view ດ້ວຍສາຍໄຟສາຍ.
- ເຊື່ອມຕໍ່ຫມໍ້ໄຟ: Connect the battery to the charge controller first. Ensure the battery has sufficient voltage for the controller to recognize the correct battery type (12V or 24V). Connect the positive (+) and negative (-) terminals correctly.
- ເຊື່ອມຕໍ່ແຜງແສງອາທິດ: Connect the solar panel to the charge controller. Ensure correct polarity (+ and -).
- ເຊື່ອມຕໍ່ການໂຫຼດ: Connect the DC load to the charge controller. Ensure correct polarity (+ and -).
ສຳຄັນ: ໃຫ້ເຊື່ອມຕໍ່ແບັດເຕີຣີກ່ອນສະເໝີ, ຈາກນັ້ນຕໍ່ແຜງໂຊລາເຊວ, ແລະສຸດທ້າຍຕໍ່ອຸປະກອນສາກໄຟ. ຕັດການເຊື່ອມຕໍ່ໃນລຳດັບກົງກັນຂ້າມ: ສາກໄຟ, ຈາກນັ້ນຕໍ່ແຜງໂຊລາເຊວ, ຈາກນັ້ນຕໍ່ແບັດເຕີຣີ.
Install the controller in a well-ventilated area, away from direct sunlight and moisture. Mount it as close to the battery as possible to prevent voltage drop in the battery cables.
8. ຄໍາແນະນໍາການດໍາເນີນງານ
Once installed, the controller will automatically begin charging. The LCD display provides real-time information about your system.
8.1. ໂໝດສະແດງຜົນ
The LCD cycles through various display screens automatically. You can also manually cycle through them or enter parameter setting mode using the buttons.
8.2. ການຕັ້ງຄ່າພາລາມິເຕີ
To adjust charging and discharge parameters:
- ກົດ ເມນູ button (left button) to enter the parameter setting interface.
- ໃຊ້ Up (middle) and ລົງ (right) buttons to navigate through parameters.
- ກົດ ເມນູ button again to select a parameter for modification. The value will start flashing.
- ໃຊ້ Up ແລະ ລົງ ປຸ່ມເພື່ອປ່ຽນຄ່າ.
- ກົດ ເມນູ button to confirm the new value and exit the modification mode for that parameter.
- ກົດຄ້າງໄວ້ ເມນູ ປຸ່ມເພື່ອອອກຈາກການໂຕ້ຕອບການຕັ້ງຄ່າພາລາມິເຕີ.
Refer to the specific icons on the LCD for battery status, solar charging status, and load discharge status.
9. ບໍາລຸງຮັກສາ
ການບຳລຸງຮັກສາເປັນປະຈຳຮັບປະກັນປະສິດທິພາບທີ່ດີທີ່ສຸດ ແລະ ອາຍຸການໃຊ້ງານທີ່ຍາວນານຂອງຕົວຄວບຄຸມການສາກໄຟພະລັງງານແສງຕາເວັນຂອງທ່ານ.
- ກວດສອບການເຊື່ອມຕໍ່: ກວດເບິ່ງທຸກການເຊື່ອມຕໍ່ສາຍໄຟເປັນແຕ່ລະໄລຍະເພື່ອຄວາມແຫນ້ນຫນາແລະການກັດກ່ອນ.
- ທຳຄວາມສະອາດຕົວຄວບຄຸມ: ຮັກສາຕົວຄວບຄຸມໃຫ້ສະອາດ ແລະ ບໍ່ມີຝຸ່ນ ແລະ ສິ່ງເສດເຫຼືອ. ໃຊ້ຜ້າແຫ້ງເພື່ອທຳຄວາມສະອາດ.
- ການລະບາຍອາກາດ: ຮັບປະກັນວ່າພື້ນທີ່ຕິດຕັ້ງມີລະບາຍອາກາດດີເພື່ອປ້ອງກັນຄວາມຮ້ອນເກີນໄປ.
- ສຸຂະພາບຫມໍ້ໄຟ: Monitor your battery's health and ensure it is properly maintained according to the battery manufacturer's guidelines.
10. ການແກ້ໄຂບັນຫາ
ຖ້າທ່ານພົບບັນຫາກັບຕົວຄວບຄຸມການສາກໄຟພະລັງງານແສງຕາເວັນຂອງທ່ານ, ໃຫ້ອ້າງອີງເຖິງບັນຫາ ແລະ ວິທີແກ້ໄຂທົ່ວໄປຕໍ່ໄປນີ້:
| ບັນຫາ | ສາເຫດທີ່ເປັນໄປໄດ້ | ການແກ້ໄຂ |
|---|---|---|
| ບໍ່ມີຈໍສະແດງຜົນ / ບໍ່ມີພະລັງງານ | ແບດເຕີຣີບໍ່ໄດ້ເຊື່ອມຕໍ່ຫຼື voltage; reversed polarity; loose connection. | ກວດສອບການເຊື່ອມຕໍ່ຫມໍ້ໄຟແລະ voltagອ. ຮັບປະກັນວ່າມີຂົ້ວທີ່ຖືກຕ້ອງ. ຂັນຂົ້ວທັງໝົດໃຫ້ແໜ້ນ. |
| ແບັດເຕີຣີບໍ່ໄດ້ສາກ | ແຜງໂຊລາເຊວບໍ່ໄດ້ເຊື່ອມຕໍ່ ຫຼື ມີພະລັງງານຕໍ່າtage; reversed polarity; shading on panels; faulty panel. | ກວດສອບການເຊື່ອມຕໍ່ແຜງໂຊລາເຊວ ແລະ ແຮງດັນtagອ. ຮັບປະກັນວ່າຂົ້ວທີ່ຖືກຕ້ອງ. ກຳຈັດເງົາໃດໆ. ທົດສອບຜົນຜະລິດຂອງແຜງໂຊລາເຊວ. |
| ໂຫຼດບໍ່ເຮັດວຽກ | Load not connected or reversed polarity; battery low; load overcurrent; load output disabled. | Check load connections and polarity. Charge battery. Reduce load. Check load output settings on controller. |
| Overcurrent/Short circuit protection activated | Load current exceeds controller rating; short circuit in load wiring. | Reduce load or use a smaller load. Inspect load wiring for short circuits. The controller should self-recover once the fault is cleared. |
11. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ
ສໍາລັບຂໍ້ມູນການຮັບປະກັນຫຼືການສະຫນັບສະຫນູນດ້ານວິຊາການ, ກະລຸນາຕິດຕໍ່ຮ້ານຂາຍຍ່ອຍຂອງທ່ານຫຼືຜູ້ຜະລິດໂດຍກົງ. ຮັກສາໃບຮັບເງິນການຊື້ຂອງທ່ານໄວ້ເປັນຫຼັກຖານການຊື້.
ສໍາລັບການຊ່ວຍເຫຼືອເພີ່ມເຕີມ, ກະລຸນາໄປຢ້ຽມຢາມ Hyuduo Store.