Sarmert 3-Lead Hard-Wire Kit for Micro-USB Dash Cams

1. ບົດແນະນຳ

This manual provides detailed instructions for the installation and operation of the Sarmert 3-Lead Hard-Wire Kit. This kit is designed to provide continuous power to your Micro-USB compatible dash camera, enabling features such as 24-hour parking monitoring and low voltage protection. It converts 12V-24V vehicle power to a stable 5V/2.5A output for your device.

ຮູບ 1: ເກີນview of the Sarmert 3-Lead Hard-Wire Kit and included fuse taps.

2. ຜະລິດຕະພັນເກີນview ແລະຄຸນສົມບັດ

The Sarmert Hard-Wire Kit ensures your dash camera operates reliably with advanced power management features.

ຄຸນ​ນະ​ສົມ​ບັດ​ທີ່​ສໍາ​ຄັນ​:

• Automatic Parking Mode: Powers on and records automatically when the vehicle is accessed, supporting time-lapse or continuous recording.
• Vol ກວ້າງtage ຄວາມເຂົ້າກັນໄດ້: Compatible with 12V-24V vehicles (cars, trucks, buses). Adjustable protection voltage ການ​ຕັ້ງ​ຄ່າ​.
• 24/7 Parking Monitor: Provides constant power to the dash cam for continuous surveillance, protecting against theft.
• ຕ່ ຳtage ການປົກປ້ອງ: Intelligent system automatically cuts power to prevent vehicle battery drain when voltage drops below 11.6V (for 12V systems) or 23.2V (for 24V systems).
• Micro-USB Compatibility: Designed for Micro-USB dash cams, GPS navigators, and radar detectors, freeing up the cigarette lighter port.

ເນື້ອໃນຊຸດ:

• Sarmert 3-Lead Hard-Wire Kit with Micro-USB connector
• Assorted Fuse Taps
• ຟິວຫຼາກຫຼາຍຊະນິດ
• ຄູ່ມືເຈົ້າຂອງ (ເອກະສານສະບັບນີ້)

Figure 2: Contents of the Sarmert Hard-Wire Kit package.

Figure 3: The 3-lead hard-wire kit provides multiple protections including battery drain, over-current, short-circuit, reverse connection, and overheat protection.

3. ການຕິດຕັ້ງແລະການຕິດຕັ້ງ

Proper installation is crucial for the hard-wire kit's functionality. If you are unfamiliar with vehicle electrical systems, it is recommended to seek professional assistance.

ແຜນຜັງສາຍ:

The hard-wire kit consists of three main wires:

• ສາຍສີດຳ (GND): Connect to a metal bolt or screw on the vehicle chassis for ground.
• ສາຍສີແດງ (ACC): Connect to a fuse in the fuse box that is only powered when the ignition is on (Accessory power).
• ສາຍສີເຫຼືອງ (BAT+): Connect to a fuse in the fuse box that has constant power, even when the ignition is off (Battery power).

Figure 4: Hard-wire kit control box showing input and output cables, and connections for GND, ACC, and BAT+.

ຂັ້ນ​ຕອນ​ການ​ຕິດ​ຕັ້ງ​:

1. ຊອກຫາກ່ອງ Fuse ຂອງທ່ານ: Refer to your vehicle's owner's manual to find the location of the fuse box. Common locations include under the dashboard, in the glove compartment, or under the hood.
2. ລະບຸຊ່ອງຟິວ: Using a circuit tester, identify a fuse slot that provides ACC power (on with ignition) for the Red wire and a fuse slot that provides constant BAT+ power (always on) for the Yellow wire.
3. Select Correct Fuse Type: Choose the appropriate fuse tap from the kit that matches the fuse type in your vehicle's fuse box.
4. Connect Wires to Fuse Taps: Insert the Red and Yellow wires into their respective fuse taps. Insert the original fuse into the lower slot of the fuse tap and a new fuse (matching the original's amperage) into the upper slot for the hard-wire kit.
5. Insert Fuse Taps: Plug the fuse taps into the identified ACC and BAT+ fuse slots.
6. Locate a Ground Point: Connect the Black (GND) wire to a secure metal bolt or screw on the vehicle's chassis that is free of paint or rust.
7. ສາຍ​ທາງ​: Carefully route the Micro-USB output cable to your dash camera, ensuring it does not interfere with driving controls or airbags. Conceal the cable behind trim panels for a clean installation.
8. ເຊື່ອມຕໍ່ຫາ Dash Cam: Plug the Micro-USB connector into your dash camera.
9. ລະບົບການທົດສອບ: Start your vehicle to ensure the dash cam powers on. Turn off the vehicle and remove the key to verify the parking monitor mode activates (if enabled on your dash cam).

Figure 5: Visual guide for the hard-wire kit installation process within a vehicle.

4. ຄໍາແນະນໍາການດໍາເນີນງານ

Parking Monitor Mode:

Once correctly installed, the hard-wire kit enables your dash camera's parking monitor function. When your vehicle is turned off, the kit continues to supply power from the vehicle battery, allowing the dash cam to record in parking mode (e.g., time-lapse or motion detection, depending on your dash cam's features).

ຕ່ ຳtage ການປົກປ້ອງ:

The hard-wire kit features an integrated low voltage protection system to prevent excessive drain on your vehicle's battery. If the vehicle battery voltage drops below a preset threshold, the kit will automatically cut power to the dash camera.

• For 12V batteries, power is cut at 11.6V, 12.0V, 12.2V, or 12.4V (user adjustable).
• For 24V batteries, power is cut at 23.6V, 24.0V, 24.4V, or 24.8V (user adjustable).

To adjust the protection voltage, press and hold the '+' or '-' buttons on the hard-wire kit box for 3 seconds to display the current setting, then use the buttons to select the desired voltage. The digital display on the hard-wire kit box will show the current voltage ການຕັ້ງຄ່າ.

Figure 6: Low voltage protection thresholds for 12V and 24V batteries.

5. ບໍາລຸງຮັກສາ

• ກວດກາປົກກະຕິ: ກວດກາສາຍໄຟເປັນໄລຍະໆເພື່ອໃຫ້ແນ່ໃຈວ່າສາຍໄຟບໍ່ມີອາການສວມໃສ່, ເສຍຫາຍ ຫຼື ການເຊື່ອມຕໍ່ວ່າງ.
• ຄວາມສົມບູນຂອງຟິວ: Ensure the fuses in the fuse taps are correctly seated and not blown. Replace blown fuses with ones of the same ampອາຍຸ.
• ຄວາມສະອາດ: Keep the hard-wire kit box and connections free from dust and moisture.
• ເງື່ອນໄຂສິ່ງແວດລ້ອມ: Avoid exposing the kit to extreme temperatures or direct sunlight for prolonged periods, which could affect its lifespan.

6. ການແກ້ໄຂບັນຫາ

Figure 7: The hard-wire kit is compatible with Micro-USB devices, not USB-C or Mini-USB.

7. ຂໍ້ມູນຈໍາເພາະ

8. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

For warranty information or technical support, please refer to the documentation provided with your purchase or contact Sarmert customer service directly. Keep your proof of purchase for any warranty claims.

You can visit the Sarmert store for more information: Sarmert Store