PIZZELLO Caldo 43-Inch Propane Fire Pit Table Instruction Manual

1. ຂໍ້ມູນຄວາມປອດໄພທີ່ສໍາຄັນ

Read and understand all instructions and safety warnings before assembling, operating, or servicing this appliance. Failure to follow these instructions could result in fire, explosion, property damage, personal injury, or death.

• ສຳ ລັບໃຊ້ພາຍນອກເທົ່ານັ້ນ: Never operate this appliance indoors or in an enclosed area.
• PROPANE GAS WARNING: This appliance uses propane gas. Ensure proper ventilation and never store propane cylinders indoors.
• ການ​ລ້າງ​ການ​ເຜົາ​ໄຫມ້​: Maintain adequate clearance from combustible materials. Refer to local codes and regulations.
• CSA CERTIFIED: This PIZZELLO fire pit table is CSA certified, ensuring it meets high safety standards for propane fuel use.
• ຄວາມປອດໄພຂອງເດັກນ້ອຍ: Keep children and pets away from the fire pit during operation and while it is cooling down. Never leave children unattended near the appliance.
• ພື້ນທີ່ຮ້ອນ: The fire pit and surrounding surfaces will be hot during and after use. Allow sufficient time for cooling before touching.
• ປະເພດນໍ້າມັນເຊື້ອໄຟ: Use only Liquefied Petroleum Gas (LPG). Do not use natural gas or any other fuel.

2. ເນື້ອໃນຊຸດ

Verify all components are present and undamaged before assembly. If any parts are missing or damaged, do not proceed with assembly and contact customer service.

• Fire Pit Table (43"x23"x24.8") x 1
• Glass Wind Guard (23.6"x9.3"x4") x 1
• Fire Glass Stones (8 LBS) x 1
• ແຜ່ນປ້ອງກັນ x 1
• Removable Lid x 1

3. ການຕິດຕັ້ງ & ການປະກອບ

Follow these steps for proper assembly. It is recommended to have two people for certain steps.

3.1. ວິດີໂອຄູ່ມືການປະກອບ

For a visual guide, please refer to the official assembly video:

3.2. ຂັ້ນຕອນໂດຍຂັ້ນຕອນສະພາ

1. ການ​ກະ​ກຽມ​ພື້ນ​ຖານ​: Lay the table top (part 6) upside down on a soft, clean surface to prevent scratches. Attach the side panels (parts 1 and 2) to the table top using the provided screws and washers.
2. ຕິດຕັ້ງອຸປະກອນຮອງຮັບພາຍໃນ: Connect the internal support bars (part 8) to the side panels (parts 1 and 2) using screws. These bars provide structural integrity.
3. ຄັດຕິດແຜງດ້ານໜ້າ: Secure the front panel (part 5) to the assembled structure. Ensure all connections are tight.
4. Install Propane Tank Tray: Attach the propane tank tray frame (part 4) to the base structure. This frame includes wheels for easy access to the propane tank.
5. Install Drawer Tracks: Stretch the glide tracks (part 9L and 9R) and attach them to the side panels and the propane tank tray frame. Ensure the tracks are correctly oriented (Left/Right).
6. Attach Rear Panel: Secure the rear panel (part 3) to complete the main body of the fire pit table.
7. ວາງແກ້ວໄຟ: Carefully pour the 8 LBS of fire glass stones (part 12) into the burner area. Distribute them evenly around the burner.
8. Install Wind Guard: Assemble the glass wind guard (part 13) according to its separate instructions and place it around the burner area.
9. ເຊື່ອມຕໍ່ຖັງ Propane: Slide out the tank storage tray. Connect a 20 lb propane tank (not included) to the gas line. Ensure all connections are secure and check for leaks using a soapy water solution.

4. ຄໍາແນະນໍາການດໍາເນີນງານ

Follow these steps to safely ignite and operate your PIZZELLO fire pit table.

1. ກ່ອນ​ທີ່​ຈະ​ເຮັດ​ໃຫ້​ມີ​ແສງ​: Ensure the propane tank valve is fully open. Remove the removable lid from the burner area.
2. ລະບົບເອເລັກໂຕຣນິກ: Push and turn the control knob to the 'LOW' position. While holding the knob, press the electronic ignitor button repeatedly until the burner lights.
3. Release Control Knob: Once the burner is lit, continue to hold the control knob for 15 seconds to allow the thermocouple to heat up. Release the knob; the burner should remain lit. If the burner does not light or goes out, wait 5 minutes and repeat the lighting procedure.
4. ປັບໄຟ: Rotate the control knob to adjust the flame height and heat output (up to 50,000 BTUs) to your desired level.
5. ປິດ: Turn the control knob to the 'OFF' position. Close the valve on the propane tank. Allow the unit to cool completely before covering or moving.

4.1. Converting to a Table

When not in use as a fire pit, the included removable lid allows you to convert the unit into a functional dining table, coffee table, or casual bar table.

5. ບໍາລຸງຮັກສາ

ການບຳລຸງຮັກສາເປັນປະຈຳຮັບປະກັນອາຍຸການໃຊ້ງານທີ່ຍາວນານ ແລະ ປອດໄພຂອງໂຕະເຕົາໄຟຂອງທ່ານ.

• ທໍາຄວາມສະອາດ: Clean the exterior surfaces with a soft cloth and mild soap solution. Avoid abrasive cleaners.
• Faux Stone Care: The faux stone surface is manufactured with specially formulated polyurethane, fire retardants, and UV inhibitors. Clean gently to maintain its visual appeal.
• ການປົກຫຸ້ມຂອງປ້ອງກັນ: Always use the provided waterproof protective cover when the fire pit is not in use and has cooled down. This protects it from weather elements.
• ການບຳລຸງຮັກສາເຕົາໄຟ: Periodically inspect the burner and gas connections for any signs of damage or blockages. Keep the burner ports clear of debris.

6. ການແກ້ໄຂບັນຫາ

If you encounter issues with your fire pit table, refer to the following common problems and solutions:

7. ຂໍ້ມູນຈໍາເພາະ

Detailed product specifications for your reference.

8. ການຮັບປະກັນແລະການສະ ໜັບ ສະ ໜູນ

Your PIZZELLO fire pit table comes with a 12-month warranty from the date of purchase.

For any questions, concerns, or warranty claims, please contact our customer service team. We are committed to responding within 24 hours to assist you.

ຕິດຕໍ່ບໍລິການລູກຄ້າ: Refer to your purchase documentation or the PIZZELLO official webເວັບໄຊທ for ສໍາລັບລາຍລະອຽດການຕິດຕໍ່.