Alphacool Eisblock Aurora Acryl GPX-N RTX 3090/3080 Ti HOF Water Block User Manual

1. ບົດແນະນຳ

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Alphacool Eisblock Aurora Acryl GPX-N RTX 3090/3080 Ti HOF water block. This high-performance water block is designed to provide superior cooling for NVIDIA GeForce RTX 3090 and RTX 3080 Ti HOF series graphics cards, enhancing stability and performance through efficient liquid cooling. Please read this manual thoroughly before proceeding with installation.

2. ຂໍ້ມູນຄວາມປອດໄພ

ຄຳເຕືອນ: Improper installation or handling of liquid cooling components can lead to system damage, including leaks and electrical shorts. Always exercise caution and follow instructions carefully.

• ໃຫ້ແນ່ໃຈວ່າລະບົບຄອມພິວເຕີຂອງທ່ານປິດເຄື່ອງຢ່າງສົມບູນ ແລະ ໄດ້ຖອດປລັກອອກຈາກປລັກສຽບຝາກ່ອນທີ່ຈະເລີ່ມການຕິດຕັ້ງ.
• ປ່ອຍໄຟຟ້າສະຖິດອອກຈາກຮ່າງກາຍຂອງທ່ານໂດຍການສຳຜັດວັດຖຸໂລຫະທີ່ມີດິນກ່ອນທີ່ຈະຈັບຕ້ອງອົງປະກອບຕ່າງໆ.
• Use only distilled water or approved liquid cooling fluids. Do not use tap water.
• Perform a leak test for at least 24 hours before powering on your system.
• ຮັກສາສ່ວນປະກອບທັງ ໝົດ ໃຫ້ໄກຈາກເດັກນ້ອຍ.
• ຖ້າທ່ານບໍ່ແນ່ໃຈກ່ຽວກັບຂັ້ນຕອນໃດໆ, ໃຫ້ປຶກສາກັບນັກວິຊາການທີ່ມີຄຸນວຸດທິ.

3. ເນື້ອໃນຊຸດ

Please verify that all items are present in your package. If any items are missing or damaged, contact your retailer or Alphacool support immediately.

• Alphacool Eisblock Aurora Acryl GPX-N RTX 3090/3080 Ti HOF Water Block
• Integrated Backplate
• Screws ຕິດຕັ້ງແລະ Spacers
• ຜ້າກັນຄວາມຮ້ອນ (ຕັດກ່ອນ ຫຼື ເປັນແຜ່ນ)
• ການວາງຄວາມຮ້ອນ
• RGB Adapter Cable (if applicable)
• ຄູ່ມືການຕິດຕັ້ງ (ເອກະສານນີ້)

4. ການຕິດຕັ້ງແລະການຕິດຕັ້ງ

This section outlines the general steps for installing the water block onto your graphics card. Specific steps for disassembling your graphics card may vary by model; refer to your graphics card manufacturer's documentation for detailed disassembly instructions.

4.1 ການກະກຽມກາດກຣາບຟິກ

1. Carefully remove the stock cooler from your graphics card. This typically involves unscrewing the mounting screws from the GPU die and removing screws securing the shroud and backplate.
2. Thoroughly clean the GPU die and all memory modules (VRAM) and voltage regulator modules (VRM) of any residual thermal paste or thermal pad material using isopropyl alcohol and a lint-free cloth.

4.2 ການນຳໃຊ້ວັດສະດຸຄວາມຮ້ອນ

1. Apply a small amount of thermal paste to the center of the GPU die. Spread it evenly to a thin layer using a spatula or by allowing the pressure from the water block to spread it.
2. Cut the provided thermal pads to the correct sizes as indicated in the included diagram (if applicable) or as per the Alphacool installation guide for your specific GPU model.
3. Carefully place the thermal pads onto the VRAM and VRM components. Ensure good contact and coverage. The Alphacool Eisblock design utilizes 1mm thick thermal pads for optimal component contact and cooling performance.

4.3 ການຕິດຕັ້ງບລັອກນໍ້າ

1. Align the Alphacool Eisblock Aurora water block with the mounting holes on your graphics card.
2. Gently lower the water block onto the graphics card, ensuring the GPU die makes contact with the copper base and thermal pads are correctly seated.
3. ຍຶດບລັອກນໍ້າໃຫ້ແໜ້ນໂດຍໃຊ້ສະກູຕິດຕັ້ງທີ່ໃຫ້ມາ. ຂັນສະກູໃຫ້ແໜ້ນໃນຮູບແບບຂວາງເພື່ອຮັບປະກັນຄວາມດັນທີ່ສະໝໍ່າສະເໝີ, ແຕ່ຢ່າຂັນແໜ້ນເກີນໄປ.
4. Connect the digital RGB cable from the water block to a compatible 3-pin 5V addressable RGB header on your motherboard or a dedicated RGB controller.

ຮູບທີ 1: ທາງເທິງ view of the Alphacool Eisblock Aurora Acryl GPX-N water block, showcasing the clear acrylic top, internal flow paths, and nickel-plated copper base.

Figure 2: The Alphacool Eisblock Aurora water block illuminated with vibrant digital RGB lighting, highlighting the internal coolant channels and beveled edges.

ຮູບ 3: ດ້ານຫລັງ view of the Alphacool Eisblock Aurora water block, showing the integrated black backplate which provides structural support and additional passive cooling.

4.4 Integrating into the Cooling Loop

1. Install appropriate G1/4" fittings (not included) into the inlet and outlet ports of the water block.
2. Connect the water block to your existing or new custom liquid cooling loop using tubing. Ensure all connections are secure and leak-free.
3. Fill your cooling loop with coolant and perform a leak test. It is highly recommended to use an air pressure leak tester before introducing liquid. Once filled, run the pump for at least 24 hours with the system powered off (using a PSU jumper) to check for any leaks. Place paper towels under all connections to easily spot drips.

5. ຄໍາແນະນໍາການດໍາເນີນງານ

Once the water block is successfully installed and the liquid cooling loop has passed a leak test, you can power on your system.

• ການເລີ່ມຕົ້ນເບື້ອງຕົ້ນ: Monitor coolant levels and temperatures closely during the first few hours of operation.
• ການຄວບຄຸມ RGB: The integrated digital RGB lighting can be controlled via your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light, Gigabyte RGB Fusion) or a dedicated Alphacool RGB controller. Ensure the 3-pin 5V ARGB header is correctly connected.
• ການຕິດຕາມອຸນຫະພູມ: Use monitoring software to keep track of your GPU temperatures to ensure optimal cooling performance.

6. ບໍາລຸງຮັກສາ

Regular maintenance ensures the longevity and optimal performance of your liquid cooling system.

• ການປ່ຽນນໍ້າຢາຫລໍ່ເຢັນ: It is recommended to replace the coolant every 6-12 months, depending on the coolant type and system usage.
• ລະ​ບົບ Flush​: ເມື່ອປ່ຽນນ້ຳຢາຫຼໍ່เย็น, ໃຫ້ພິຈາລະນາລ້າງທໍ່ລະບາຍຄວາມຮ້ອນທັງໝົດດ້ວຍນ້ຳກັ່ນ ຫຼື ນ້ຳຢາທຳຄວາມສະອາດສະເພາະເພື່ອກຳຈັດສິ່ງເສດເຫຼືອທີ່ສະສົມໄວ້.
• Block Inspection: Periodically inspect the water block for any signs of corrosion, algae growth, or blockages. If necessary, disassemble and clean the block using appropriate cleaning agents for acrylic and copper.
• ການກວດສອບອຸປະກອນເສີມ: Ensure all fittings remain tight and leak-free.

7. ການແກ້ໄຂບັນຫາ

ພາກສ່ວນນີ້ແກ້ໄຂບັນຫາທົ່ວໄປທີ່ທ່ານອາດຈະພົບ.

• ປະສິດທິພາບຄວາມເຢັນບໍ່ດີ:
  • Ensure proper thermal paste application and thermal pad contact.
  • Check for air bubbles trapped in the water block. Tilt the system gently to dislodge them.
  • Verify pump is operating correctly and coolant flow is adequate.
  • Inspect radiators for dust buildup and clean if necessary.
• ຮົ່ວ:
  • ປິດລະບົບທັນທີ.
  • Identify the source of the leak. Tighten fittings or replace O-rings/tubing as needed.
  • Perform another leak test before powering on.
• ແສງ RGB ບໍ່ເຮັດວຽກ:
  • Check the connection of the 3-pin 5V ARGB cable to the motherboard or controller.
  • Ensure the RGB header is enabled in your motherboard's BIOS/UEFI.
  • Verify that the correct RGB software is installed and configured.

8. ຂໍ້ມູນຈໍາເພາະ

9. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

Alphacool products are manufactured to high quality standards. For warranty information, please refer to the terms and conditions provided with your purchase or visit the official Alphacool webເວັບໄຊ.

For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact Alphacool customer service through their official webເວັບໄຊ:www.alphacool.com