EverBrite EB-70LED-Dimmer-Motion Under Cabinet Lighting User Manual

1. ບົດແນະນຳ

This manual provides detailed instructions for the installation, operation, and maintenance of your EverBrite EB-70LED-Dimmer-Motion Under Cabinet Lighting. Please read this manual thoroughly before using the product to ensure proper function and safety.

2. ຄຸນລັກສະນະຂອງຜະລິດຕະພັນ

• Hand Wave Control: Easily turn the light on or off with a simple hand wave within 4 inches of the sensor.
• Adjustable Brightness (Dimmer): Hold your hand under the sensor in 'On Mode' to adjust the light intensity. The light remembers your last brightness setting.
• Motion Sensor (Auto Mode): The light automatically turns on when motion is detected within 10 feet (3 meters) and a 130-degree angle in dark conditions. It turns off after 20 seconds of no motion.
• ແບັດເຕີຣີທີ່ສາມາດສາກໄດ້: Equipped with a premium 2400 mAh rechargeable battery for extended use. The automatic sensor helps conserve battery life.
• ໄຟ LED ທີ່ບໍ່ມີ Flicker: Features 70 bright LEDs providing 300 lumens of 6000K light, designed to be gentle on the eyes and reduce visual fatigue.
• ການຕິດຕັ້ງແບບຍືດຫຍຸ່ນ: Offers tool-free installation using either a magnetic strip for metal surfaces or double-sided adhesive tape for other surfaces like glass, wood, or stucco.

3. ເນື້ອໃນຊຸດ

ຮັບປະກັນວ່າສິນຄ້າທັງໝົດມີຢູ່ ແລະ ຢູ່ໃນສະພາບດີເມື່ອຖອດອອກ:

• EverBrite EB-70LED-Dimmer-Motion Under Cabinet Light Bar (2 units)
• ສາຍສາກ USB
• Metal Plates with 3M Adhesive (for mounting on non-magnetic surfaces)
• Integrated 2400 mAh Lithium Polymer Battery

4. ຂໍ້ມູນຈໍາເພາະ

5. ການຕິດຕັ້ງ

The EverBrite Under Cabinet Light offers two simple, tool-free installation methods:

5.1 ການຕິດຕັ້ງແມ່ເຫຼັກ

If your desired mounting surface is metal, the light bar can be directly attached using its built-in magnets.

1. Ensure the metal surface is clean and dry.
2. Simply place the light bar against the metal surface. The magnets will hold it in place.

5.2 Adhesive Installation (for Non-Metal Surfaces)

For surfaces such as wood, glass, or stucco, use the provided metal plates with 3M adhesive.

1. Clean the desired mounting surface thoroughly to ensure it is free of dust and grease.
2. Peel off the protective film from one side of the 3M adhesive on the metal plate.
3. Attach the metal plate to the back of the light bar, aligning it with the magnetic area.
4. Peel off the protective film from the other side of the 3M adhesive on the metal plate.
5. Press the light bar firmly onto the cleaned non-metal surface for at least 30 seconds to ensure strong adhesion.

Image: Demonstrates attaching the metal plate to the light bar and then mounting it with adhesive.

ຮູບພາບ: ຫຼາຍກວ່າview of the light bar, highlighting the USB port, ON-OFF-AUTO switch, and dimensions (17.48" L x 2.01" W x 1.93" H).

6. ຄໍາແນະນໍາການດໍາເນີນງານ

The light bar features a switch with three positions: ON, OFF, and AUTO. Select the desired mode for operation.

6.1 ON Mode (Manual Control & Dimming)

In this mode, the motion sensor function is disabled. You control the light manually.

• ເປີດ/ປິດ: Wave your hand within 4 inches of the sensor.
• ເພື່ອປັບຄວາມສະຫວ່າງ: Hold your hand under the sensor within 4 inches. The brightness will cycle from high to low and back to high. Remove your hand when the desired brightness is reached. The light will remember the last brightness setting.

Image: Close-up of the light in ON mode, illustrating the hand waving function for control.

Image: Demonstrates stepless dimming by holding a hand under the sensor, with brightness levels indicated from 100% down to 10%.

6.2 AUTO Mode (Motion Sensor)

In this mode, the light operates automatically based on motion detection and ambient light conditions. The hand wave control is disabled.

• The light will turn on when motion is detected in sufficiently dark conditions.
• The motion sensor has a detection range of up to 10 feet (3 meters) with a 130-degree angle.
• The light will automatically turn off after 20 seconds of no motion being detected.

Image: Explains the two lighting modes, highlighting the motion and light sensor functionality in AUTO mode.

ໝາຍເຫດ: The functions in ON mode and AUTO mode do not overlap. Ensure the switch is in the correct position for your desired operation.

7. ການສາກໄຟ

The EverBrite light bar is equipped with a rechargeable battery. When the light dims or stops working, it's time to recharge.

1. Locate the USB charging port on the side of the light bar.
2. Connect the provided USB charging cable to the light bar's port and to a standard USB power source (e.g., computer, USB wall adapter).
3. A charging indicator light will typically illuminate during charging and change color or turn off when fully charged.
4. A full charge usually takes 4-5 hours and provides approximately 5.5 hours of continuous use. The battery can be recharged over 300 times.

Image: Shows the light bar connected to a USB charger, indicating its 2400 mAh rechargeable battery and charging times.

8. ບໍາລຸງຮັກສາ

• ທໍາຄວາມສະອາດ: ເຊັດແຖບໄຟດ້ວຍຜ້າອ່ອນໆແລະແຫ້ງ. ຢ່າໃຊ້ນໍ້າຢາທໍາຄວາມສະອາດທີ່ມີສີຂັດ ຫຼື ຕົວລະລາຍ.
• ການດູແລຫມໍ້ໄຟ: To prolong battery life, avoid fully discharging the battery frequently. Recharge the light when it starts to dim. If storing for a long period, charge the battery every 3-6 months.
• ການເກັບຮັກສາ: ເກັບຮັກສາແສງສະຫວ່າງໄວ້ໃນບ່ອນທີ່ເຢັນ, ແຫ້ງ, ຫ່າງຈາກແສງແດດໂດຍກົງແລະອຸນຫະພູມທີ່ສຸດ.

9. ການແກ້ໄຂບັນຫາ

10. ຂໍ້ມູນຄວາມປອດໄພ

• Do not disassemble, repair, or modify the product. This may cause electric shock, fire, or damage.
• ເກັບຮັກສາຜະລິດຕະພັນໃຫ້ຫ່າງຈາກນໍ້າ ແລະ ຄວາມຊຸ່ມຊື່ນສູງ.
• ຢ່າປ່ອຍໃຫ້ຜະລິດຕະພັນຖືກແສງແດດໂດຍກົງຫຼືອຸນຫະພູມສູງສໍາລັບໄລຍະເວລາທີ່ຍາວນານ.
• ຮັກສາໃຫ້ໄກຈາກເດັກນ້ອຍ.
• ໃຊ້ພຽງແຕ່ສາຍ USB ທີ່ໃຫ້ມາສຳລັບການສາກໄຟ.
• Avoid looking directly into the LED light for prolonged periods, as it may cause eye strain.

11. ວິດີໂອຜະລິດຕະພັນຢ່າງເປັນທາງການ

Watch these official videos for visual guidance on installation and features.

12. ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

For warranty information or technical support, please refer to the product packaging or contact EverBrite customer service. Keep your purchase receipt for any warranty claims.