Aexit WH806C Wire Tracker and Cable Tester User Manual

1. ຜະລິດຕະພັນເກີນview

The Aexit WH806C is a versatile instrument designed for identifying and tracing wires or cables without damaging their insulation. It is also capable of checking for short circuits, locating open circuits, and identifying the status of telephone lines. This kit includes a Sender (Emitter) and a Receiver, making it an essential tool for network and telephone line engineering, as well as other metal conductor line projects.

ຄຸນນະສົມບັດທີ່ສໍາຄັນ

• Wire Tracing: Accurately trace cables and wires, and diagnose break points.
• ການ​ທົດ​ສອບ​ຕໍ່​ເນື່ອງ​: Judge the continuity of cables or wires.
• Telephone Line Status: Identify the state of a working telephone line (clear, ringing, busy).
• ການຜະລິດສຽງ: Send a single solid tone or dual alternating tone to the target cables or wires.
• ການອອກແບບທີ່ເປັນມິດກັບຜູ້ໃຊ້: Features an easy-to-operate interface, flexible connections, and a portable design.
• Visual and Audible Indicators: Equipped with indicator lights and sound reminders for clear feedback.

ຮູບທີ 1.1: The Aexit WH806C Wire Tracker and Cable Tester kit, showing the emitter, receiver, and various connection cables.

2. ເນື້ອໃນຊຸດ

ກະ​ລຸ​ນາ​ກວດ​ສອບ​ວ່າ​ລາຍ​ການ​ທັງ​ຫມົດ​ທີ່​ລະ​ບຸ​ໄວ້​ຂ້າງ​ລຸ່ມ​ນີ້​ແມ່ນ​ລວມ​ຢູ່​ໃນ​ຊຸດ​ຂອງ​ທ່ານ​:

• 1 x Emitter (Sender) Unit
• 1 x ຫນ່ວຍຮັບ
• ແບັດເຕີຣີ 2 x 9V
• ຫູຟັງ 1 x
• 1 x ຄູ່ມືຜູ້ໃຊ້ (ເອກະສານນີ້)
• 1 x Easy Carry Nylon Case

ຮູບທີ 2.1: The Aexit WH806C kit, including the carrying case and original packaging.

3. ຂໍ້ມູນຈໍາເພາະ

4. ການກໍານົດອົງປະກອບ

Familiarize yourself with the main components of the Aexit WH806C kit:

ຮູບທີ 4.1: Emitter and Receiver units with battery compartments open, showing 9V batteries.

ຮູບທີ 4.2: Close-up of the Emitter unit, highlighting the RJ45 and RJ11 ports, and the function switch (CONT, OFF, SCAN, TONE).

ຮູບທີ 4.3: Close-up of the Receiver unit, showing the 'PUSH TO TEST' button, the probe tip, and the speaker grille.

5. ຕັ້ງຄ່າ

5.1 ການຕິດຕັ້ງຫມໍ້ໄຟ

1. Locate the battery compartments on the back of both the Emitter and Receiver units.
2. Slide open the battery covers.
3. Insert one 9V battery into each compartment, ensuring correct polarity (+/-).
4. ປິດຝາປິດແບັດເຕີຣີໃຫ້ແໜ້ນ.

ໝາຍເຫດ: Always use fresh 9V batteries for optimal performance. Remove batteries if the device will not be used for an extended period.

5.2 ສາຍເຊື່ອມຕໍ່

The Emitter unit features RJ45 and RJ11 ports, as well as alligator clips for various connection types. Select the appropriate connector for your testing needs.

• RJ45: For Ethernet/LAN cables.
• RJ11: For telephone lines.
• ຄລິບແຂ້: For bare wires or other metal conductors.

6. ຄໍາແນະນໍາການດໍາເນີນງານ

6.1 Wire Tracing Function

This function allows you to locate a specific wire or cable within a bundle.

1. Connect the Emitter to the cable you wish to trace using the appropriate connector (RJ45, RJ11, or alligator clips).
2. Set the Emitter's function switch to the "SCAN" position. The Emitter will begin sending a tone signal.
3. ເປີດເຄື່ອງຮັບສັນຍານ.
4. Move the Receiver's probe tip along the suspected path of the cable.
5. Listen for the audible tone from the Receiver. The tone will be loudest when the Receiver is closest to the target cable.
6. Use the earphone for clearer detection in noisy environments.

6.2 ການທົດສອບຄວາມຕໍ່ເນື່ອງ

To check if a cable or wire has a continuous electrical path.

1. Connect the Emitter to the cable using the alligator clips or RJ connectors.
2. Set the Emitter's function switch to the "CONT" ຕໍາ​ແຫນ່ງ​.
3. If the cable is continuous, the Emitter's indicator light will illuminate, and a tone may be heard.
4. If there is a break in the cable (open circuit), the indicator will not light up.

6.3 Telephone Line Status Identification

Determine the current state of a telephone line.

1. Connect the Emitter to the telephone line using the RJ11 connector.
2. Set the Emitter's function switch to the "TONE" ຕໍາ​ແຫນ່ງ​.
3. Observe the indicator lights on the Emitter:
   • ແສງສີຂຽວ: Indicates a clear line.
   • ໄຟແດງ: Indicates a busy line.
   • ກະພິບໄຟແດງ: Indicates a ringing line.

6.4 Short Circuit and Open Circuit Location

The continuity test (Section 6.2) can help identify short and open circuits. For precise location of an open circuit, use the wire tracing function:

1. Perform a continuity test to confirm an open circuit.
2. Connect the Emitter to one end of the cable.
3. Set the Emitter to "SCAN" ໂໝດ.
4. Trace the cable with the Receiver. The tone will stop or significantly weaken at the point of the open circuit.

7. ບໍາລຸງຮັກສາ

7.1 ການທົດແທນຫມໍ້ໄຟ

When the indicator lights dim or the tone weakens, it's time to replace the 9V batteries in both units. Follow the battery installation steps in Section 5.1.

7.2 ການທໍາຄວາມສະອາດ

Wipe the units with a soft, dry cloth. Do not use abrasive cleaners or solvents, as they may damage the casing.

7.3 ການເກັບຮັກສາ

Store the Aexit WH806C kit in its provided nylon case in a cool, dry place away from direct sunlight and extreme temperatures. Remove batteries if storing for extended periods to prevent leakage.

8. ການແກ້ໄຂບັນຫາ

• ບໍ່ມີພະລັງງານ / ຫນ່ວຍງານບໍ່ເປີດ:
  Check if the 9V batteries are correctly installed and have sufficient charge. Replace batteries if necessary.
• No Tone from Receiver during Tracing:
  Ensure the Emitter is set to "SCAN" mode and properly connected to the cable. Verify the Receiver is turned on and its battery is charged. The cable might be too deep or shielded, or there might be an open circuit.
• Inaccurate Continuity Test Results:
  Ensure all connections are secure and clean. Check for corrosion on connectors or alligator clips.
• Weak or Intermittent Tone:
  This often indicates low battery power in either the Emitter or Receiver. Replace batteries. Also, ensure the cable is not excessively long or heavily shielded.
• Telephone Line Status Not Detected:
  Ensure the RJ11 connector is firmly plugged into an active telephone line. Verify the Emitter is set to "TONE" mode.