ແນະນຳ
This manual provides detailed instructions for the installation, operation, and maintenance of the DIGITEN G1 Water Flow Sensor, Model FL-808. This Hall effect flow sensor is designed for accurate measurement of liquid flow within a range of 1 to 60 liters per minute. Please read this manual thoroughly before use to ensure proper function and safety.
ສິນຄ້າເກີນview
The DIGITEN G1 Water Flow Sensor (Model FL-808) is a robust and reliable device for measuring water flow. It features G1 (0.5 inch) threaded connections for easy integration into various systems. The sensor outputs a square wave pulse signal proportional to the flow rate, making it suitable for microcontrollers and other electronic systems.
ຄຸນນະສົມບັດທີ່ສໍາຄັນ:
- ການກໍ່ສ້າງທົນທານ: Waterproof, heat-resistant, pressure-resistant, and cold-resistant design.
- ຂອບເຂດການໄຫຼກວ້າງ: Measures flow from 1 to 60 Liters per minute.
- ການຕິດຕັ້ງງ່າຍດາຍ: Simple G1 (0.5 inch) threaded connections.
- Pulse Output: Generates a square wave pulse signal for flow rate calculation.
- ປະຕິບັດຕາມ RoHS: ຕອບສະໜອງມາດຕະຖານດ້ານສິ່ງແວດລ້ອມ.
ຂໍ້ມູນຄວາມປອດໄພ
- ໃຫ້ແນ່ໃຈວ່າການປິດການສະຫນອງພະລັງງານກ່ອນທີ່ຈະຕິດຕັ້ງຫຼືບໍາລຸງຮັກສາ.
- Do not exceed the maximum operating pressure of 1.75 MPa.
- Verify correct wiring connections to prevent damage to the sensor or connected equipment.
- Avoid installing the sensor in locations with extreme vibrations or corrosive environments.
- This device is intended for water flow measurement. Do not use with other liquids without verifying compatibility.
ເນື້ອໃນຊຸດ
- 1 x DIGITEN G1 Water Flow Sensor (Model FL-808)
ຂໍ້ມູນຈໍາເພາະ
| ຕົວແບບ | FL-808 |
| ວັດສະດຸ | Metal (Internal components), Plastic (Housing) |
| ຂະໜາດການເຊື່ອມຕໍ່ຂາເຂົ້າ/ອອກ | G1 (0.5 inch) Threaded |
| ລະດັບອັດຕາການໄຫຼ | 1 - 60 L/min |
| ຄວາມກົດດັນໃນການເຮັດວຽກສູງສຸດ | 1.75 MPa (17.5 Bar) |
| ການດໍາເນີນງານ Voltage ຂອບເຂດ | DC 5 - 24 V |
| ປະຈຸບັນປະຕິບັດງານ | Cannot exceed 10 mA (at DC 5V) |
| ສັນຍານອອກ | Square Wave Pulse |
| Frequency Formula | F = 4.8 * Q (L/min) ± 2% |
| Output Pulse per Liter | Approximately 450 pulses/liter |
| ອຸນຫະພູມປະຕິບັດການ | ≤ 80°C |
| ຄວາມຊຸ່ມຊື່ນປະຕິບັດການ | 35% - 90% ຄວາມຊຸ່ມຊື່ນ |
| ອຸນຫະພູມການເກັບຮັກສາ | -25°C ເຖິງ +80°C |
| ຄວາມຊຸ່ມຊື້ນ | 25% - 95% ຄວາມຊຸ່ມຊື່ນ |
| ຄວາມຕ້ານທານ insulation | > 100 MΩ |
| ຄວາມຍາວສາຍ | 15 ຊຕມ |
| ນ້ຳໜັກສິນຄ້າ | 80 ກຣາມ |
ການຕິດຕັ້ງແລະການຕິດຕັ້ງ
1. ການຕິດຕັ້ງກົນຈັກ
The flow sensor features G1 (0.5 inch) male threaded connections on both ends. Ensure the flow direction arrow on the sensor body aligns with the intended water flow in your system. Apply appropriate thread sealant (e.g., PTFE tape) to prevent leaks. Tighten connections securely but do not overtighten.
ຮູບ 1: ດ້ານຫນ້າ view of the DIGITEN G1 Water Flow Sensor, showing the G1 threaded connections and the product label.
Figure 2: Technical drawing illustrating the dimensions and internal structure of the DIGITEN G1 Water Flow Sensor.
2. ສາຍໄຟຟ້າ
The sensor has a 3-wire connection. Connect the wires as follows:
- ສາຍສີແດງ: VCC (+) - Connect to DC 5V to 24V power supply.
- ສາຍດຳ: GND (-) - Connect to ground.
- ສາຍສີເຫຼືອງ: Signal Output - Connect to your microcontroller or data acquisition system's input pin.
ຮັບປະກັນການດໍາເນີນການ voltage is within the specified range of DC 5-24V. The current drawn by the sensor should not exceed 10mA at 5V DC.
ຮູບທີ 3: ໄລຍະໃກ້ view of the sensor's wiring connections: Red (VCC), Black (GND), and Yellow (Signal).
ຮູບທີ 4: ລາຍລະອຽດ view of the 3-pin connector attached to the sensor's cable.
ຄໍາແນະນໍາການດໍາເນີນງານ
ຫຼັກການຂອງການດໍາເນີນງານ
The DIGITEN G1 Water Flow Sensor uses a Hall effect sensor to detect the rotation of an internal turbine. As water flows through the sensor, it spins a turbine, and a magnet attached to the turbine generates a series of electrical pulses. The frequency of these pulses is directly proportional to the flow rate of the water.
Flow Rate Calculation
The output signal is a square wave. The flow rate (Q in L/min) can be calculated from the measured frequency (F in Hz) using the following formula:
F = 4.8 * Q (L/min)
Therefore, to find the flow rate:
Q (L/min) = F / 4.8
The sensor provides approximately 450 pulses per liter of water. The accuracy is ±2%.
ຮູບທີ 5: ພາຍໃນ view of the sensor, highlighting the turbine mechanism responsible for pulse generation.
Figure 6: The sensor with its label clearly visible, detailing model number, working range, and wiring information.
ບໍາລຸງຮັກສາ
- ການກວດກາປົກກະຕິ: Periodically check for any signs of leaks at the connections or damage to the sensor body and wiring.
- ທໍາຄວາມສະອາດ: If the sensor's accuracy degrades, it may be due to debris accumulation inside the turbine. Disconnect power and water supply, then carefully remove the sensor for inspection and cleaning. Use a soft brush and clean water to remove any obstructions.
- ການເກັບຮັກສາ: If storing the sensor for an extended period, ensure it is clean, dry, and kept within the specified storage temperature and humidity ranges (-25°C to +80°C, 25%-95% RH).
ການແກ້ໄຂບັນຫາ
| ບັນຫາ | ສາເຫດທີ່ເປັນໄປໄດ້ | ການແກ້ໄຂ |
|---|---|---|
| ບໍ່ມີສັນຍານອອກ |
|
|
| Inaccurate flow readings |
|
|
| ຮົ່ວໃນການເຊື່ອມຕໍ່ |
|
|
ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ
For warranty information or technical support, please contact DIGITEN customer service through the retailer where the product was purchased or visit the official DIGITEN website. Please have your product model number (FL-808) and purchase details ready when contacting support.