ECOELER YM2106 Wall Switch Vacancy & Occupancy Sensor Instruction Manual

ແນະນຳ

This manual provides comprehensive instructions for the installation, operation, and maintenance of the ECOELER YM2106 Wall Switch Vacancy & Occupancy Sensor. This device is designed to automatically control lighting and motor loads based on motion detection, offering energy savings and convenience. It supports both manual-on (vacancy sensor) and automatic-on (occupancy sensor) switching modes.

ຂໍ້ມູນຄວາມປອດໄພທີ່ສໍາຄັນ

WARNING: RISK OF ELECTRIC SHOCK. Improper installation can lead to serious injury or death. Always turn off power at the circuit breaker before installation or servicing. Installation should be performed by a qualified electrician or in accordance with local electrical codes.

• ອ່ານຄໍາແນະນໍາທັງຫມົດກ່ອນທີ່ຈະຕິດຕັ້ງ.
• Do not install with power on.
• ສໍາລັບການນໍາໃຊ້ພາຍໃນເຮືອນເທົ່ານັ້ນ.
• ຮັບປະກັນວ່າການເຊື່ອມຕໍ່ສາຍໄຟປອດໄພ.
• ປະຕິບັດການ voltage: 120/277Vac, 60Hz.
• Neutral wire is not required for operation.

ເນື້ອໃນຊຸດ

ກວດ​ສອບ​ວ່າ​ອົງ​ປະ​ກອບ​ທັງ​ຫມົດ​ແມ່ນ​ມີ​ຢູ່​ກ່ອນ​ທີ່​ຈະ​ເລີ່ມ​ຕົ້ນ​ການ​ຕິດ​ຕັ້ງ​:

• ECOELER YM2106 Sensor Switch
• ແຜ່ນຕິດຝາ (1)
• screws
• ໝວກສາຍ
• ຄູ່ມືການຕິດຕັ້ງ (ເອກະສານນີ້)

ຂໍ້ມູນຈໍາເພາະ

ຄໍາແນະນໍາການຕິດຕັ້ງ

ກ່ອນທີ່ທ່ານຈະເລີ່ມຕົ້ນ: Turn OFF power at the circuit breaker or fuse box. Ensure the power is completely disconnected before proceeding.

1. ກະກຽມສາຍໄຟ: Carefully remove the existing wall switch from the electrical box. Identify the LINE (hot), LOAD, and GROUND wires. The ECOELER YM2106 does not require a neutral wire.
2. ເຊື່ອມຕໍ່ສາຍ:
   • ເຊື່ອມ​ຕໍ່ ສາຍສີດໍາ from the sensor to the LINE (hot) wire from the electrical box. Secure with a wiring cap.
   • ເຊື່ອມ​ຕໍ່ ສາຍສີແດງ from the sensor to the LOAD wire (to the light fixture/motor) from the electrical box. Secure with a wiring cap.
   • ເຊື່ອມ​ຕໍ່ ສາຍສີຂຽວ from the sensor to the GROUND wire from the electrical box. Secure with a wiring cap.
   • Cap off any unused wires in the electrical box, such as a neutral wire, if present.
3. ຕິດເຊັນເຊີ: Gently fold the wires into the electrical box. Insert the sensor into the electrical box and secure it with the provided screws.
4. ຕິດຕັ້ງແຜ່ນຕິດຝາ: Attach the decorative wall plate over the sensor and secure it.
5. ຟື້ນຟູພະລັງງານ: ເປີດໄຟຢູ່ທີ່ຕົວຕັດວົງຈອນ.
6. ການ​ທໍາ​ງານ​ຂອງ​ການ​ທົດ​ສອບ​: The green LED indicator light on the sensor will flash when motion is detected, confirming active detection.

Note: If you are unsure about any wiring steps, consult a qualified electrician.

ການດໍາເນີນງານ

The ECOELER YM2106 sensor supports two primary modes of operation: Vacancy (Manual-On) and Occupancy (Automatic-On).

Vacancy Sensor (Manual-On) Mode

In this mode, the lights/motor will only turn ON when you manually press the switch button. Once ON, the sensor will keep the lights/motor ON as long as motion is detected within its coverage area. The lights/motor will turn OFF automatically after no motion is detected for the set time delay.

Occupancy Sensor (Automatic-On) Mode

In this mode, the lights/motor will turn ON automatically when motion is detected within the sensor's coverage area. The lights/motor will remain ON as long as motion is detected and will turn OFF automatically after no motion is detected for the set time delay.

To switch between modes or adjust settings, refer to the "Configuration and Settings" section.

ການຕັ້ງຄ່າແລະການຕັ້ງຄ່າ

The ECOELER YM2106 sensor features adjustable settings for time delay, sensitivity, and ambient light level. These adjustments are typically made via small dials or switches located on the sensor itself, often behind the wall plate.

• ການຊັກຊ້າເວລາ: This setting determines how long the lights/motor remain ON after the last detected motion. It is adjustable from 5 seconds to 30 minutes. Adjust clockwise for longer delays, counter-clockwise for shorter delays.
• ຄວາມອ່ອນໄຫວ: This controls the sensor's responsiveness to motion. Higher sensitivity detects smaller movements or movements at greater distances. Lower sensitivity requires more significant motion or closer proximity. Adjust as needed to prevent false triggers or missed detections.
• Ambient Light Level (Photocell): This setting allows the sensor to hold the lights/motor OFF if sufficient natural light is present in the room, even if motion is detected. This feature helps save energy by preventing artificial lighting from turning on unnecessarily. Adjust to your desired light threshold.

Consult the diagrams on the sensor unit itself for the exact location and labeling of these adjustment controls.

ບໍາລຸງຮັກສາ

• ທໍາຄວາມສະອາດ: Periodically wipe the sensor lens with a soft, dry cloth to remove dust or debris that may obstruct detection. Do not use abrasive cleaners or solvents.
• ການກວດກາ: Regularly check the sensor and wall plate for any signs of damage or loose connections.
• ບໍ່ມີສ່ວນທີ່ຜູ້ໃຊ້ບໍລິການ: The sensor contains no user-serviceable parts. Do not attempt to open or repair the unit.

ການແກ້ໄຂບັນຫາ

ການຮັບປະກັນແລະການສະຫນັບສະຫນູນ

For warranty information or technical support, please contact ECOELER customer service. Retain your proof of purchase for warranty claims.

Contact information is typically found on the product packaging or the manufacturer's official webເວັບໄຊ.

ຂໍ້ມູນຂ່າວສານສື່ມວນຊົນ

No product images or official product videos were provided in the source data to embed in this manual.